Ford 7.3L Power Stroke (1999-2003) :: Slight Creaking Sound Coming From Front Driver Side
Jan 6, 2016
Tonight on my way home I noticed a slight creaking sound, coming from front driver side, opening the window it was more noticeable. So when I got home I have tried to locate the source, it is the same with or without the engine running & you can hear it by rocking the steering just a little left to right. It sounds like a dry bush, I had my good lady rocking the wheel while I climbed underneath but couldn't pinpoint it, so I climbed up on the fender with my weight on the radiator support & the battery cover, when she turned the wheel the sound was almost gone but as soon as I jumped off it was back! I then tried rocking the truck from the driver side fender & the sound is there but not quite so pronounced, Any other way before I spray everything with WD40 (don't know if you have that over there but it usually quietens things like this!) There is no play on anything anywhere & the truck has only around 32k miles.
View 4 Replies
Advertisement
MY '07 SuperCab just started making a strange rhythmic sound as I drive. It is coming from the drivers side front wheel area. It is like a short creaking sound. It stays the same if I am turning the tires. Seems to go away if I put the brakes on hard, but I slow down so much I am not sure. Front CV Joint?
View 1 Replies
I'm having a squeak/rattle type sound coming from my front drivers side wheel (more rattle). It only happens when I go over a quick bump and happens going straight and while turning. 2012 f250. 87k miles. 4x4. I have a two inch block level (southern truck) up front..
View 14 Replies
Early 99 F250 7.3 Manual 4WD Extended Cab Short Bed
I am at a loss. I have a slight vibration/medium roar seemingly coming from front. I have tried fixing/replacing several things, with no luck. When I get above 35-40 mph, I can hear a whirling vibration that sounds like tire tread noise (very little tread on tires). When I tap the brakes, seems to make a difference, seems to get louder as I slow down. I can feel it in the clutch and accel. pedals. It is consistent, when I push clutch in and let idle at 45mph, it is still there. Doesn't seem to make a difference when swaying back and forth, maybe a little. When i get below 25-30mph it isn't noticeable.
Here is what i've done so far :
1.Replaced both front wheel bearing assemblies, rotors and brakes
2.Replaced drivers side brake caliper (seemed to be sticking a bit?), will do passenger side tomorrow
3.Serviced both hub locks and verified front axle is not engaged (one was locked for some time, I thought I found issue, but still have vibration)
4. Tightened pitman arm joint, was slightly loose (need to replace)
5. Inspected tie rod ends and other joints, see no noticeable movement, but have not marked them off the culprit list.
6. Tightened output shaft nut, was a little loose
7. Raised rear end off on jack stands, and revved up to 50 mph, and no vibration, so I have excluded u joint and cardan joint, everything points to front end
8. Rotated tires, left front to right rear
What I haven't done :
1. Have a leak in pinion seal, not replaced yet
2. Seems the upper and lower ball joint had the slightest, I mean slightest play in it when lifting the front driver side wheel (I mean less than 16th inch) but could hear it. I haven't done anything with this yet ... may be the problem? Would a tire out of balance wreak this much havoc with this amount of movement?
3. Haven't replaced the pitman arm joint, will but not sure if this can create issue.
Nothing I've done seems to make a difference.
View 14 Replies
So I have a ticking sound that has me puzzled. I thought it could be coming from the drivers side of the engine. This weekend, actually on Monday I decided to do the hot re-torque on the diver side. I warm up the engine for about 15min and have at it. I had put this off for weeks because it has been way too hot. Dam it was still too hot, I was sweating buckets. I had to stop several times to clear the sweat off my head my eyes my shades .I torqued everything to spec and nothing moved.
I went to 125 inch lbs and I got movement on the rear two injectors. I gave them about 1/2 a turn and stopped. I put everything back together, I used hair spray form the 99 ct store. It seemed OK. Fast forward to Tue. I needed to be sure so I went for the boost leak test. Here is my concern. I was going to test to about 30 PSIG, but I ended up at about 40 psig and I forgot to disconnect the MAP sensor! How likely is it that I damaged the sensor, and how can I tell? She is pretty stock and does not have a boost fooler to protect the sensor. Nothing popped and I did not leave the the HP on very long.
View 5 Replies
I have a sensor on the top of the engine on the driver side that has oil coming out of it. I think it is called an IPC but I want to make sure before I go buy a new one. It sits right behind the power Steering pump. I am replacing the Power steering pump and hoses so I thought I would replace that as well. Also since there is oil in the connection what is the best way to clean the connection electric parts cleaner? By the way this is a 2000 7.3 4x4 ....
View 11 Replies
I have not had much fun with the front end of my 1999 4x4 7.3 diesel dually. Well I replaced the ball joints with moogs over the winter. Just recently I my truck has developed a thumping sound that I can feel under my driver side floor board. The weird thing is that it does not do it all the time. But yesterday I noticed it for a more extended amount of time.
View 14 Replies
So my '01 E350 has been fine but tonight when I went to start it I didn't get a WTS light and the SES light was on and there was a weird number on my PHP Hydra that looked like r5 ? This happened a few times back to back so I tried starting it and it just cranked and cranked. Wtf? So I started pushing the button on the chip and all of the sudden I got the WTS light and the hydra flashed, now the chip was on tune 10 instead of 5 where it was when I parked it. I should also note that during these episodes there was a fairly loud clicking/clunking sound coming from the drivers front under the hood when I toggle the key on.. Sounds like maybe a relay? Louder than I recall ever hearing.
View 5 Replies
I blocked off the hpop discharge tube to test for leaks, shop air. I am plugged into the oil rail drivers side, and keep getting a slight popping sound. The first time I did this it took ten minutes to start, so I replaced the top injector seals. The second time it did this after about four minutes, so I took the oil rail to the local shop and they did the ball tube orings in the rail, now I went to put it back on and it does it almost right away.
Am I just pushing the oil out of the injectors? is this normal or should I have NO air noise period? I guess I am not sure how these injectors work, where does the oil go after it enters the top of the injector? It seems like it's coming more from the top coil area, more so perhaps than under the oil rail.
View 6 Replies
Alright so I'm having a problem with my 2003 Ford Explorer. I've recently noticed that when I get to above 40 mph, if my steering wheel is straight, I hear a loud kind of grinding or humming sound coming from my left driver side front. If I am going about 65 mph, it gets even louder and if I crank the steering wheel to the left, that's when it really gets noisy but as soon as I crank it to the right, the problems gone. When I do hear the hummin sound, I can feel it in the steering wheel. I have replaced al of the tires and it didn't work. Also, the car slightly pulls me to the right.
View 10 Replies
I have an air leak sound coming from I believe the driver side. Sounds like an air line from a compressor leaking. Could see anything obvious last night or hear well over engine. When driving it's pushing more air. Nothing looked/felt loose. Didn't find any air blowing were I could stick my hand in a hot engine. Doesn't seem to have performance issue, maybe a little more turbo delay.
View 3 Replies
I have 1999 F350 7.3 Crew Cab 4WD. I took it on a 4 hours trip towing a trailer to haul a small tractor on it. after 3 hours of driving, I started hearing grinding and metal chewing sound coming from the front axle or close the wheel hubs. It was awful, terrible, ... you name it!!! I had to continue or I will lose the tractor I paid for already. The sound was coming for 1-2 seconds each 500 feet or so. It never stopped or changed. I pulled over to see what's going on and found the following:
1. Left shock is leaking badly
2. Right locking hub is gone (not sure if the truck had one before). I bought this truck last year, but I never had to use 4x4 and I know the 4x4 motor by the transfer case is missing and the nipple on the transfer case is set to the 2wd position so the front drive-shaft does not turn.
I took the front shock off and continued to drive without it, the noise did not go away.
I pulled over again and this time I noticed that the dust cover on each end of the front axle is missing too. I have never worked on these axles before, but I jacked one side, and sure enough, gear oil was leaking from the other side. I took the plug off the front differential and stuck my finger in it. I felt a creamy brown-greenish stuff in the differential. The consistency is like mayonnaise or thin peanut butter. I put the plug back on and went to pick up the tractor because I did not want to miss it fooling around with the truck on the highway.
The truck made it there and back (almost 5 hours total after the break down). The sound never stopped every 500 to 1000 ft.
After getting home safely, I took the other locking hub off, and took it for a test drive. I did not hear the noise, but now my right brakes are locking.
I took of the wheels and saw that the retaining snap ring (C clip) for the front axle on the right side came off by hand. I took the washers behind it off. Took the calipers and brackets off. I have never done front axle rebuild. I am not sure what has been damaged and what's still good.
Right of the bat, I know, at least, I need 2 shocks, one brake caliper and pads.
My questions are:
1. Is it possible to take the front axles off on both sides and make it 2wd for now until I have the money to rebuild the axle?
2. Could I use the same hubs? or they are most likely damaged and how to tell?
3. How to tell if the differential is damaged/needs rebuilding?
4. How to tell if the axles/spindles are damaged?
5. Is there a step by step tutorial to rebuild the axle with all seals, bearings, ...etc? How hard is the job for a hobbyist? I do most of my repairs myself, and I was lucky at 36 years old, I never had to rebuild a differential.
6. What else I might have damaged in the process of driving it that long with the noise? How do I tell if I did?
View 8 Replies
I have a 2003 F150 manual 4WD with 4.6L engine and 165000 miles. When i am driving i feel a vibration in the steering wheel and on floor board that intensifies when i press the accelerator. I do hear an irregular humming that sounds like it is coming from the driver side front. I checked the wheel for any play but it was very tight. i check tie rod ends, ball joints no play. i recently changed both u-joints on the rear shaft and the bearing hub on the passenger side front. Also, the steering feels a little 'wobbly' when i make sharp turns. it almost feels like it is giving. What else should i check?
View 1 Replies
2001 F 150 5.4 V8 4WD. I have a weird creaking sound coming from the front end, sounds like the passenger side, whenever I turn right at any speed. What it is?
View 6 Replies
Recently I have a vibration that I can feel slightly through the steering wheel. If I'm driving down the highway doing 70mph + I have a noise coming from the front end. Also while driving let's say 40mph and below and I let off the pedal to slow down I can here a vibration in the front that kind of sounds like a small Jake break. And when going over anything bumpy I hear like a popping metal sound. This popping sound has been going on for a long time and still can't figure it out. I replaced all my shocks thinking my old set was bottoming out. Nope, still have the same problem.
I jacked up the front end yesterday and checked for movement top and bottom and side to side thinking maybe the wheel bearings or ball joints were going. Everything is solid. Spun the wheels and no noise, no grinding, nothing. I can't figure it out. I have not removed the wheels to check and see if a caliper is loose. I will be checking that next. I did notice while looking around that I can push up on my pitman arm on the steering box. It's not a huge amount of movement but I can still move it. I can also see teeth marks between the box and the arm, not sure if that is normal or not. When I do move it up and down it sounds a lot like that metal popping sound I have been hearing. So, I know this is a lot.
View 14 Replies
I'm having a hard time diagnosing a creaking noise that is coming from the front driver side area. Since the Camry is pretty quiet, this is the one stand out noise that annoys me while driving. I placed my phone next to the front windshield to get as close as possible to the noise but am having trouble locating the exact spot. Where it's coming from.
The noise tends to appear when outside temperature is spring/summer like. In the winter I really didn't notice it. So that tells me the interior temperature is irrelevant despite warming up the cabin in winter. How this is linked to outside temperature I have no idea.
Ignore the large thump in the middle of the video as that is noise from going over potholes.
[URL] ....
View 6 Replies
Was climbing a steep hill at 35 mph just before truck down shifted to 2nd, I was hearing a pinging sound. Sounded like only I cylinder was doing so. What it could be. I am currently running a 1/4 tank of Fppf fuel injector cleaner. Is this a injector noise. No knocking just a slight pinging.
View 1 Replies
I've experienced a fuel leak, I've checked all over, and the only thing I've came up with so far, was maybe its coming from the banjo bolt going into the front of the driver side head.. I cant really get to it good enough to tell though..
View 6 Replies
I am trying to track down a creaking sound in the front end. Happens when turning mainly left but occasionally right or slow speed turning the steering wheel. I've rebuilt the front end (not because of the creak) ball joints, tie rod ends both inner and outer, sway bar bushings, power steering pump, shocks, steering shock etc. what's left? All parts have been greased good but still can't find it.
View 2 Replies
So, I have heard a little bit about the oil pump bolt issue. However, I am still confused. Was this issue fixed for the 2008 model and what are the symptoms? I changed out my valve cover last night due to a PCV valve failure. The car is running great except there is a slight rattling sound coming from the drivers side of the engine at idle. I know I left nothing around the car that could have gotten in the motor when the valve cover was off. This issue was not happening before changing the valve cover. What could be causing this noise, or is it typical for this motor?
View 3 Replies
Have a 2003 Honda Accord with 178K miles on it. Excellent service and maintenance on the car. After this winter (midwest) I notice a creaking sound (like bedsprings) coming from the front end, passenger side. Car also seems rather bouncy on rough roads. Husband check the shocks and struts and says they are fine. What else could it be? Sway bar, ball joints, etc. and estimated cost - will take to a mechanic...
View 2 Replies
