Leaving on a 200 mile trip in the morning and when checking the fluids, I found the serpentine belt trying to get off the AC pulley. I've put in on twice and it immediately jumps half way off when starting the engine. How long it's been doing this. Nothing is obviously loose or moved. What is likely causing this?
View 8 RepliesI have 1997 F250 LD since i bough it has been doing this chirping sound coming from the serpentine belt and the pulley area but when the truck has been working for 15 - 20 min it goes away
This is apart from the from the problem before I think the fan clutch is broken because when I start the truck I can hear the fan going at the same speed of the engine is that normal ? even when the truck is cold
About 2 weeks ago i noticed that the serpentine belt started shredding. I noticed it before it was all gone, so i parked it and started ordering parts before i did anything. Since i had to get the radiator hose off, i decided to flush the coolant, change the thermostat and the upper radiator hose to go around the belt. Once the parts arrived, I drained the coolant and did two flushes and tried to change the hoses and thermostat. the Gates hose ended up not being the right hose, in hindsight I should have used the old hose and put it back together.
But I returned the Gates hose and ordered a Motorcraft hose. not thinking, i left the system dry and possibly sitting with water from the previous flush. Three days ago, I got the correct Motorcraft part and did the work on Sunday. since it had been sitting, i decided to run another flush, i noticed a squeaking sound and that the water was coming out a little browner than when i left it. So I ran another two flushes and said to hell with it and put the whole thing back together and filled it with coolant and distilled water.
This morning, the squeaking sound was louder, but temps where fine and coolant level was fine. I drove to work ( about a 10 mile drive) and when i finally stopped, i got a whiff of coolant smell. I noticed coolant behind me and when i lifted the hood, i noticed the reservoir was half empty and coolant dripping down from the center of the block. I can still hear the squeaking, I figure the water pump is on its last leg and decide i need to go home. I walk in to work and let them know I'm gonna take the day off to situate this. Before i leave, i top off the reservoir with a gallon of distilled water and head out.
After a short distance I notice that the squeaking stops, now I'm terrified that the water pump just completely failed. (I've never had one fail on me so I'm not sure what happens when it does) As i drive home, I'm watching all my gauges. none of the temperature gauges spike, everything was normal for the drive home (another 10 miles) I park it and lift the hood and the reservoir is completely full. why is reservoir completely full? why would a leak like that stop? Should i just change the water pump? I don't want to just hope for the best, i do use my excursion to haul the kids from time to time.
I was cruising along yesterday and felt the steering pump go out on the highway. Nowhere to pull over and pulling a big horse trailer. Three miles later I finally get to a wide spot to dive into. I look down and the temp gauge is maxed and the oil light is on. Most of the antifreeze boils out when I got the engine shut down. I had no choice but to have a friend bring a new belt and some antifreeze to the rescue. Got it changed and filled back up. Started and drove home fine.
I've got this twisted gut feeling about the whole deal. What kind of damage did I likely do? Things to look for? Did I just kill the longevity of the motor? I've been trying to do things right and treat it well to ensure a reliable truck.
On a side note the belt came apart in ribbons and it was absolutely shredded. The belt appeared to be less than 3 months old. No cracks or tears and a bright white numbers sticker on the back
My serp belt started squealing so I pulled the thermostat housing to inspect the rubber gasket. It looked OK, but I cleaned up both surfaces and replaced with a new gasket, and put it back together. The housing was replaced just a couple months ago along with new hoses. It was not corroded and OK to reuse.
Started the truck up and saw a slowish/steady drip of red Cat ELC dripping on the driveway. Opened the hood up again and carefully inspected around the thermostat housing - no coolant is leaking there.
I did notice the same slow/steady drip coming from just behind and beneath the thermostat housing. See in pic, this is where it is dripping. One other question, what is this plug for on the side of the water pump?
The last week or so I have been having a screeching belt sound driving me insane in my 2003 F-250 7.3. After further investigating I have found out it is coming from my 11 month old GTP38R bearing. It has an aftermarket billet compressor wheel in it and I sold the factory wheel when I installed the Billet wheel. Where to locate a factory Garrett GTP38R wheel? All I can find online are Billet wheels or random off brands. At this point I would even trade my Billet wheel for a factory 38R wheel.
View 6 RepliesJust a quick question, my serpentine belt fell off while driving on the freeway today and wondering what are the possible causes for this too happen? First things that came too mind were tensioner or worn out belt. Hard to believe the belt would be worn out though as it only has 65k miles.
View 7 Replies2006 6.0l ... I've read all over for tips on routing this belt and everyone plays it off as being some simple '20-minute' task. I'm on my 4th hour on this now.
I can't figure out how to route the belt around the tensioner pulley, circled in the picture (from another thread). Everyone glosses over how to do this and I can't figure it out.
It seems like the only way to get it on is to bend the belt and slide it between the pulley and the block, but that I just can't reach the blasted thing.
I noticed my serpentine belt started squeaking about 3 days ago. And yesterday as I was driving to work I heard a clicking sound coming from the left side of the hood, then my car started to gradually shut down and white smoke was coming from the engine. When I got to the stoplight it completely turned off, but I was able to turn it back on again to turn into the parking lot before it shut off again. When I checked it there were no visible leaks, my reservoir for my coolant was still full, and my meter never went up indicating that my car was over heating. I'm not sure what's wrong with it, but after it sits for awhile it is able to turn back on again for a while.
View 3 RepliesHaving issues with seat belt disconnecting on its own? Ill be driving down the road and it just unbuckles......i figure its got gunk in it so I will and try and clean.... maybe spring is weak.
View 6 RepliesThought I had these bookmarked but not. What is the torque value for the 13 mm bolt , replacing the tensioner.
View 4 RepliesOk, I have 1997 Ford Ranger, 4cyl, manual transmission, and more miles than I'd like to admit to.
Yesterday, I noticed that one of the vacuum lines was coming dangerously close to hitting the serpentine belt on the front of the engine. The clamp that normally holds the vacuum line in place rusted away a decade ago, so I decided to use some velcro ties to attach the line to the positive battery cable. I didn't twist or pull on the cable in any way and the vacuum line isn't applying any force to the cable.
I get in the truck a few hours later, hit the key and I get >click<, but nothing out of the starter. One click when the key is in the start position, nothing more (as opposed to click-click-click).
Not thinking about my repair earlier, I went down to Autozone and had them test the battery - 12.8V and 550CCA, no problem there.
So then, I thought well since the click is coming from the starter relay, maybe that's where the problem is. I read on another forum that sometimes the starter relay can be resurrected temporarily by hitting it with a hammer. Which I did. And it did work! Now the truck is starting up normally every time, but I'd like to replace whatever was bad.
My questions :
1. Did I prove anything by hitting the starter relay with a hammer and then starting the truck?
2. Should I still be looking at the battery cables?
3. Should I stop hitting random parts with a hammer and take this truck down to a real mechanic before I do serious damage?
I have a 2003 f150 4.2 v8. and i have a squeaky belt I am almost positive its the belt i went to change it today but being sick,cold (NY), getting dark having just worked 10 hrs and changing oil it was not going well.
The reason I think its the belt it does not squeak when its really cold out but once it warms up a little its back so I am thinking when it gets warm it stretches out a little and when its cold it shrinks up or am I just crazy..
A noise has been coming from my Serp belt for awhile. My serpentine belt doesn't have any wear. At least It doesn't look like it. Will this noise go away by replacing it? or is it something else? Is it the tensioner? I've noticed when car warms up the noise goes away. I do not know the last time it was replaced.
Here is a video : [URL] .....
Car - 2001 Jetta TDI with 230k miles.
There has been a noise coming from the serpentine belt area for some times now, and I thought when I get to work on the belt I will get it fixed.
Last night, I replaced the alternator with a brand new one from idpart with a clutch pulley (the original pulley was plastic). I also replaced the tensioner and serpentine belt with this kit from ECS: [URL] .....
Everything was put back tight and nicely. Turned on the engine: the noise is still there.
For sure there is one pulley on its way out, but with one?
Video here: [URL] .....
Noticeable @ 0:47
It's a 2.0 AVH Jetta.
Is it time to replace? There is a noise coming from the belt and when I listen with the hood up my best guess is that it's the tensioner. I'm not sure if it is easy to replace or if that is even the problem. The belt looks fine. It allows me to twist it barely less than halfway so to me it does not seem loose. But in the rain last week got the battery light and lost power steering, power brakes, etc, then it went back to normal and hasn't failed again since. The car has 131,000 miles.
Is there a way to check the tensioner? It's pretty tight in there. Or am I wrong as to what the problem is? The sound is a rubbing/slight clicking sound that is in time with the engine and you can hear it if you listen inside the car when the engine is on. The belt also seems to wander around on the tensioner just a little. One day it was about a mm in too much, a few days later, a few mm out, in relation to the pulley.
Got a nice rattle coming from the serpentine belt area of the camry, before I order some parts, I'm thinking the bearing in the tensioner is done, I just don't want to swap it out only to find out its my water pump barking or alternator bearing/bushing. doesn't seem to be emanating from the alternator.
Here's the short video : [URL] ....
So, when I was leaving work I started my car up and heard what sounds like a low grinding noise coming from the area where the serpentine belt is. Let the car idle and it remained.
Put the car in gear and drove off and the sound was still there. the sound gets louder as I increase my speed. It went away a couple of times when I was braking, then came back.
I stopped at the gas station and could still hear it. After getting gas, fired the car back up and heard nothing. When I drove off, the sound returned.
I got home and put it in park, leaving the car on, opened the hood and could still hear the noise. Pressed and held the gas a few times and the sound did get louder.
I am pretty sure it is coming from some rotating part, but no clue what part. What this could be?
recap:
-get noise on startup
-while driving noise gets louder
-sometimes it stops when braking
-sound coming from area of serpentine belt
2003 3.0 ranger... This will be my 3rd time replacing serpentine belt and if needed 2nd. time for idler, tension pulleys...NOT SURE WHAT TO DO, should i replace parts again?
View 5 RepliesI have a 2007 ES350. It started making a vibrating noise and sometimes screech coming from the serpentine belt area. It stops when I turn off the A/C and also stops when I accelerate with the A/C on (only does it when idling).
View 3 RepliesI have a '06 sonata 3.3 v6. Let me first describe what was happening to the car before the noise started. When I first started the car and put the ac, the first time turning the steering wheel in either direction the steering wheel would tighten up and the battery indicator light would come on and the fasten seatbelt light would flash even though I had the belt fastened. It would only happen the first time I would make a turn and after that I could turn with no problem. So in recap, it would only happen on the first turn and only when the ac was on. Now when I start the car up there is a noise coming form the pulley/belt area. I wouldn't classify it as a squeaking noise more like a grinding. I've looked at the belt and it seems to be fine. After I start to drive the car the noise goes away. If I start the car again after a drive within about 2 hours the noise doesn't happen when I start it. What this noise could be? and also could the noise and the steering wheel tightening when the ac is on be connected?
View 1 Replies