Ford 7.3L Power Stroke (1999-2003) :: Running Sluggish In 1200 - 1800 RPM Range Intermittently
Aug 13, 2016
I am still trying to debug my 7.3 running sluggish in the 1200-1800 rpm range. The problem is intermittent. I checked the wiring harness under the valve covers to verify they are plugged in and there are no opens in the circuit. I replaced the crankshaft position sensor and the high pressure oil sensor.
This will run fine one time and a few miles down the road it will chug and smoke out the exhaust until I either get into the accelerator or back off and re press the accelerator. Again, it does it intermittently hot or cold.
I ran both a cylinder contribution test and perdels with a Snap On Verus. The cct passes everytime. The perdels have a couple of cylinders 5-6 and 8 fluctuate between 0 and 1.80% with #8 up to 2.5%.
My question is. Do the cylinders in the test correspond to the actual cylinders in the engine? Reason I am asking is the Verus does not follow the firing order on a gas engine. The cct is in order of 1-8 and I have to correlate the cct order to the firing order. Found this out the hard way when I had a bat cop on a 5.4 and replaced it only to have the same cylinder still show not firing.
I got out the graph leads and tested the cylinder and pulled the injector thinking it was bad. Everything showed good but the cct still showed it not firing. I had to unplug each coil and watch the cct to determine what the true cylinder in the test was. It turned out to mimic the firing order so I am asking out of concern that cylinder 3 in the perdels is really cylinder 3 or a different cylinder.
Btw, the perdels all show 0% if the transmission is in drive. I would have thought that a load on the engine would have showed higher perdel percentages with a load on it.
View 13 Replies
Advertisement
Battery light comes on when the truck is running at less than about 1200rpm, but I see zero movement on the needle. Weird thing is i charged the batteries and tested the alternator with my multimeter and it was reading 14.1-14.2 which is nominal. Run it for about 10 min then it reads 12.3-12.8
I'm thinking a bad cell in the battery or alternator is going out. Oh and all the connections are tight, wires look good. 2001 f250 4wd 7.3 intake exhaust basic tuner gauges. Could the constant heat be a factor?
View 12 Replies
Lately I have been having problems loosing power. Truck wants to miss mostly going up hill and runs sluggish I'll pull off the road and let it idle for a minute and it will run fine. And it is only occasionally some days it don't happen at all and other days it happens quit often. New fuel filter, oil is good, had it on the scanner and isn't throwing any codes. Around 230k miles newer injectors.
View 10 Replies
I have a 1999 Ford F-350. I have six codes from my truck. The codes are P0237 P1119 P1690 P0500 P0603 P0344. My truck runs, but likes to stall out on me for no reasons at times. The other problem I am having is between 1,800-2,500 rpms, she shutters or pops.
View 7 Replies
My 2003 6.0 truck lost most of its power. It has the SCT programmer. It used to run great it would roll coal really well then it slowly started to run worse. Now it runs really sluggish especially when its cold. IT takes forever to warm up. On the freeway when ur going a constant speed it bucks and jerks a lot. It won't roll coal anymore and just runs like crap. A mechanic said I had 3 bad injectors. But I don't believe it.
View 2 Replies
My shift indicator switch on the trans seized up, so a local trans shop replaced it for me. Now I get no low range when I select it. I understand it needs to see the truck in neutral to do this, is there a simple adjustment? The trans shop is a long way away.
View 2 Replies
Just a heads up when it comes to this code. Today at work I was working on a 2000 f350 that the driver neglected on telling me he had a CEL on and truck was kind of sluggish (drivers are idiots they cant tell the difference) but no miss or any sign of problem except the CEL (he had electrical tape on the cluster. Well I put my AE to see the vitals and immediately code p1316, so I went to do a buzz test revealing that cylinder 1,3,5,7,6 were short to open circuit (forgot the codes) but they all sounded healthy. My next step since it was a quick and easy to do was to check the passenger side uvch to see for burnt pins and what not but everything checked out.
Checked the driver side #6 cyl for the same problem bit a no go. I ohm tested the injectors all of them checked out, wires all the way to the idm checked out so at this point I was in my atemp to see what the hell was going on I decided to install my obs idm on, and guess what happened next it worked immediately the sel did not come up and when I test drove it, my god it felt like a new truck.
Just a side note the idm, had no sign of water damage, and like mentioned to the untrained person most would not tell the difference on how it ran. To anybody that has checked and can't find the problem make sure you really and I mean really check your IDM really good.
View 9 Replies
7.3 2001 model starts ok at 32-35 F. Feels a bit sluggish / slow response on the road. Reach a hill after 3-4 miles. Engine temp then beginning to go above low level mark. 100 meters up the hill, going around 30 mph there is a sudden surge in the throttle although my pedal is steady. Going back a few minutes later, on flat ground at bottom of hill and with no accelerator pressure, the engine suddenly stalls. Starts fine again after I stop. The same history actually repeated on two separate days recdently on the same hill. CPS is recently replaced. Had some jerking before that, but not the behavior explained above. Current CPS is Delphi light grey. Recent fuel filter change and oil change as well
View 14 Replies
Vehicle: 2006 Mk IV Golf 2.0 GLS With 82766 mi
Back story: I purchased the vehicle from my dad who did regular maintenance except that somehow spark plugs and wires slipped through the cracks until now. A few months ago (while I was in training) it apparently started showing CEL but the few times it came on, my wife said it just disappeared. Two weeks ago, it came on again and I had the code read which came back as P0420. I took it in and they replaced the rear cat after which it ran well for a few days. Then the CEL came on again but went off before I could get out in the shop. This weekend I went ahead and changed the oil and may have over filled it slightly. The next day I went to change the spark plugs and after changing 4, 1, 3 it started to miss fire in 4 and 1. I reset both spark plugs and got 4 firing again, but 1 remained bad. With a friend I determined there was a weak spark in 1 and changed the wire but no change.
Current situation: As it stands now, it's still miss firing. The worst seems to be between 1200- 1800 rpm and if I keep it above there the light will stop flashing and even turn off on some cases. I've read that heart mixed with moisture(I just moved from AZ to WA) can lead to a cracked coil pack or that the injectors can go bad. Should I just take it to vw specialist?
View 5 Replies
I have a 2011 F250 6.7 that I bought in August of 2010. I have 35K miles on it and it has pretty much been trouble free once I got the firmware update for the shifting issues. I have the local dealership do all of my service work and all updates and service bulletins have been applied. Unfortunately on my way to work this morning the stupid Check Engine Light came on. The dealership has it now - hopefully I will know tomorrow.... I do think it has been running a little sluggish but I am not sure if that is the winter grade diesel (I use PM22-A in every single tank).
View 2 Replies
The past few weeks my truck has occasionally shown no signs of life when trying to start it. It goes through the "Wait to Start" routine and then when the key is turned ... nothing. No clicking, no cranking, nothing. All other electronics seem to work just fine.
This might happen only once ... or up to three times before it decides to crank. So far, it has eventually started on subsequent tries. When it does finally crank, it fires right away as usual and everything is as it should be and it runs great. No unusual smoke, noises or anything else.
This may be unrelated to the above issue but I noticed that lately once in a while, the back up sensors remained silent while I'm reversing and close to an object when I know they should have been beeping. (the audible override was not turned on either).
I may be grasping at straws here but would anything going wrong with the gear selector shifter cause both of these problems to surface? Like the lever isn't seating correctly and causing these issues? I also realize the two problems could be (and possibly are) totally unrelated.
I can live with the backup beeper not working but I can't survive with the truck being unreliable and not starting whenever it feels like it. It has newer, strong batteries and when it does crank, it's a "strong, fast" crank like normal.
View 7 Replies
I have this strange noise coming from the front end. It happens at the most random times. It is at the end of the video. It's kinda hard to hear over the engine noise.
[URL]
View 7 Replies
I'm getting a sound every now and then of what sounds like i'm running over rumble strips on the side of the highway. I'm guessing it's the trans grinding. Any thoughts?
View 8 Replies
I have a 2002 f350 dually with a 7.3 and 197k. At 186k it died while driving and I had it towed home. As soon as the tow truck dropped it the truck fired right up like nothing was wrong. Then it died again 2 days later. I replaced the cps, but the fix was replacing the icp and pigtail. Now it is doing the same thing again. It died on my wife while driving yesterday, i had it towed to the dealership I work at and it started and ran for about 2 hours with no issues. I hooked up the factory IDS and had a diesel tech look at it with me. The oil pressure, injector circuit and injectors, and IPR all look good. The batteries were a little weak so i replaced both of them. I drove it home yesterday, about 10 miles, and drove it around town today. Then i tried to jump start my 96 bronco and after about 10 minutes of running it sort of hick uped then 5 minutes later it died and would not start. I let it set for 30 minutes and it started and died after about a minute.
View 2 Replies
2002 F350 7.3 intermittently wont start after I've shut it off, it runs fine but sometimes won't start when it's (warm)? Wait hour or more and it starts right up.
Is there something I can look for before I bring it to a mechanic?
Just to clarify I am a gal with little wrenching skills but I can look at videos and follow directions if it's not too involved.
View 14 Replies
I have a 99 f450 with a 7.3. Here lately it has been "missing" when driving or idling, but only every now and then. When driving down the road it will start bucking and boiling black smoke out then the ses light will come on and like turning a switch everything clears up and it acts and drives normal.
View 11 Replies
Just got myself a gently used Econoline E-350 7.3 Diesel and was loving it when she ran:
E-350 7.3 Diesel
Recently I have been having some charging issues. It started with it intermittently having a hard time to start, especially when it was warm. I carried a jump box with me and that always seemed to work. Then I noticed the voltmeter on the dash dropping. It went down to the 8 and I was like something is wrong.
Checked the battery voltage, it was at 9.6v. OK, maybe alternator isn't charging. Advance Auto tested the alternator, said it was bad. I replaced alternator. No difference. I pulled the battery and ran it on a conditioner to bring it up to proper voltage. It's now at 12.6v resting. Starts the van no problem. When running though the voltage doesn't increase to 13-14 volts like it should though telling me the alternator isn't doing it's job. Increasing engine RPM actually decreases voltage? Checked all the obvious things like bad grounds but everything seemed clean.
The only thing that was fishy was when I pulled the three way plug from the alternator, one of the pins had corrosion on it. I cleaned it up before installing the new alternator. I didn't do a diode test on the new alternator because I figured it was new, but hey maybe I got a lemon?
Anyway I'm going crazy trying to figure out where the problem is. All fuses are ok. Is there an external regulator or something I should be on the lookout for? Is there anything else that could be causing a non charging issue? The battery was manufactured in 2014 so it's relatively new.
And on a random note my ABS light is now on?
View 8 Replies
I have an 02 crew cab SB 7.3L. The best way to I know to describe it is a sorta like a metal ringing noise. It just started this afternoon while pulling a 9k camper. It only does it under load. Boost stays the same and it happens in all ranges from 5psi to 15psi. It is intermittent. It sounds like it it coming from the turbo. I pulled off the boot and could not feel any play on the intake wheel.
After unhooking trailer and taking for a test drive I can not get it to do it again? The turbo was rebuilt about 4 years ago with a wicked wheel but has only seen about 18k miles since the rebuild. A quick look at the boots appear good but didn't get to take them off before going to work. I will try to post video.
View 14 Replies
I have a 03 F-350, 7.3L. There is a slow oil leak that only leaks after I've run the truck. In other words, it doesn't just sit and leak overnight. I'll park it after running, and the next morning I'll notice a small pool of oil, approximately 2" in diameter. The leak appears to be coming from the oil pan area. I degreased the entire oil pan area to get a better visual of where the leak is coming from. I can see oil trailing down the front of the oil pan and the rear of the oil pan. Does this sound like the gasket? Or, what else could it be? I'm praying its not as bad as I think and need to replace the gasket.
View 3 Replies
I have a 2003 F250 7.3L. I put new injectors in my truck four months ago and all of a sudden, I have 2 cylinders not working correctly, making the truck to run really badly. I sent the 2 injectors from the bad cylinders back for warranty and they replaced both of the injectors but nothing was wrong. I put them in and the truck still runs badly. I have a new fuel filter, new ICP, new CPS and glow plug relay. I cannot drive the truck, it smokes white at idle. I can unplug each injector at a time and cyclinder 5 does not change how the truck runs
View 14 Replies
Alternator locked up in a parking lot. Replaced it and had to replace pigtail due to a loose wire in the harness. Now battery light comes on intermittently. New alternator is doing fine producing anywhere from 13.9v to. 14.4v. No output voltage correlation to battery light at all. The belt is still in great shape so I don't suspect slipping. Fortunately I caught the old one locking up almost immediately and had recently replaced the belt. Output voltage looks great. Are there any fuses for alternator?
Only thing I can think of that I did...when splicing in the pigtail that connects to the alternator, I briefly grounded whatever wire in the pigtail is hot. Was just a split second, but enough to see a spark and maybe enough to blow a fuse? I've seen people reference an "under hood" fuse box, but I don't seem to have one. My truck is a 2002 CC with just over 100k on the clock.
View 3 Replies
