Ford 7.3L Power Stroke (1999-2003) :: Running Rough And Had No Power / Died While Driving
Mar 3, 2017
Well, I was headed out from work this morning, on my way to fill up as I was a bit below 1/4 tank.
Truck was running good, like normal, until after 5-6 minutes, when it started running rough and had no power. Worried, I pulled off the side of the road. As I did so, it died, and wouldn't start again.
I whipped out my phone, pulled up TorquePro, and ran a code check. Nada. Well, it sounds to me like it's not getting fuel possibly, so I figure the best way to check, is to drain the fuel filter bowl, and crank it some, and check the bowl. No fuel in bowl.
Wifey came to pick me up with the can of diesel I keep for starting my forge (had 3 gal maybe?). Poured it in the tank, cranked it, no start. Still nothing in the bowl.
I'm taking her to work now, so she won't be late, then I'm headed back with a full can of diesel.
If that full can still won't get it, should I keep shuttling diesel cans, or should 8 gal or so be enough to get it back to the fuel pickup level? And if it's not fuel level, what else should I start checking on the side of the road?
View 14 Replies
Advertisement
I have had this happen twice now. Starts fine, idles fine, then either sitting or just driving a block or two it starts running very rough, no smoke that I remember seeing, and now no power. Barely makes it up a hill. The first time I thought is was related to the heavy rain the night before. I had the tow truck coming and decided to try it again, this was after a few hours sitting. Ran perfectly. The second time, no wetness/rain, pulled away from the house and in a block or two, same thing ... rough, no smoke, no power. Pulled back into driveway, turned off for a minute, restarted and ran fine. Ran perfect today. What is the best injector cleaner to use in the fuel?
View 3 Replies
I have a 2001 ford 7.3l powerstroke diesel. When I first noticed the problem I was towing a trailer going up a grade and got into the throttle almost to the floor and noticed a loss of power and the service engine soon light flashing extremely rapidly a few times and never came back on. I made it home, still lacking power but not running rough. I drove the truck to work the next day and the truck was running rougher and loosing power. It ran great through lower RPM's but seemed to trip as soon as you gave it over half throttle. eventually the truck wouldn't run right at all and lacked complete power. It idled rough as well. My mechanic threw the computer on it and it said injector pressure reading too high or too low.
I was told to replace the IPR on the HPOP and I did. (I also replaced the fuel filter and changed the oil). After replacing the IPR it ran great, had full power! then it began to slowly die like it did before until it sounded like it was running off 4 cylinders again. I pulled the ipr out, cleaned it and changed the oil again. It seemed to clear it up for an hour and ran great but then began ran rough again. I also replaced the CPS sensor. I feel like its not getting enough fuel or something, im just wondering if it could be the ICP or the lift pump. There is no check engine light at all. Its just got me stumped because cleaning the IPR clears everything up.... temporarily.
View 14 Replies
2000 F250, 7.3, 170K, running rough, knocking loudly, missing, shaking, no power to get up driveway, intermittent, no codes spit out at all. No smoke visible, no leaks visible, New fuel filter, air filter, update cam sensor, new fuel rail lift pump, new uvc harness, new glow plug relay.
View 14 Replies
So there's no signal/ electrical feed to the passenger side cylinders. I ohmd all the UVCH and they check out. Moved the wiring harness around near the big black multi pin plug under the air intake to the turbo and the passenger bank kicks in and out so it's definitely a wiring short. Need links and pics to that multi pin plug to troubleshoot the wiring.....
View 8 Replies
2002 F250 7.3L suddenly idling and running very rough, and doesn't have any power. Truck has been running perfect, it's my daily driver, and just put a couple hundred miles on it yesterday with no problems. I had been having some transmission issues when I tow heavy so I bought a new transmission yesterday. This morning I pulled the truck into my garage to change the transmission. Again truck ran fine, no signs of any issues before the trans swap. I changed out the transmission, which included unhooking the trans wiring harness from all the various sensors, and unbolting the starter.
I didn't mess with anything in the engine bay except for unhooking the batteries. I had also repaired the overdrive button wires, as they had been pinched in the steering column and the button wasn't working. When I got everything hooked back up I cranked it up to get the trans fluid flowing through the transmission, it started right up and idled good. I had it running for a few minutes and it was beginning to make a little more noise than usual. When I started to back out of the garage it was getting pretty rough, almost like it was running out of diesel. I put it in neutral and gave it some throttle and noticed I was getting white smoke out of the exhaust and could smell diesel pretty strong.
I checked my injector resistance at the valve covers and got around 4 ohms +/- on all of the injectors. I rechecked all of the clips and harness that I had messed with. I took a look at the ICP sensor and it has oil in the connector which I know can cause a rough running condition in some cases. It looks like it has had oil on it for a while. I unhooked the batteries again for about 20 minutes to try and reset anything that may have messed up. I checked a bunch of connections under the hood to see if anything was unhooked or loose.
I also cleaned up the connector on the ICP sensor. I started the truck back up and it idled perfect so I pulled it back out of the garage and headed down the driveway. It almost immediately started running rough again and barely had the power to go up a small hill. I pulled back in and tried unplugging the ICP while it was running, which made a slight difference in the idle but still very rough. I plugged it back in and the idle progressively got worse until it was chugging really bad. I shut it off after that and haven't messed with it again.
What might have happened? Could it be a bad sensor or transmission position sensor in the new trans? Is it just coincidence that this happened with a transmission swap? I am going to get a new ICP, but if there is anything else I can try/check before I can pick up the ICP on Monday let me know.
View 1 Replies
I was wondering if fuel injectors throw a code when it goes out. I have a 02 7.3 been running rough when you accelerate bogs down and looses power not sure but sometimes gas light would come on knowing I have gas in it could that be a sign of the sending unite and that's why it runs rough..
View 3 Replies
I have a 2001 F350, 7.3. My service engine light came on and immediately the truck started to run rough and lose some power. I've checked the under the cover connections and they were both connected, I replaced the cam position sensor and I still have the same problem. The worse part of the hold thing is that there are no codes stored so I'm flying bind. Where to go next.
View 8 Replies
Tried starting the truck, fired ran good for a couple seconds, then ran extremely rough for a couple seconds then died.
I did some research and changed the ICP because there was oil in the connector so even if it wasnt causing my issue i wanted to replace it.
Now I have the same issue but it will actually run a little longer and not stall. I thought it was fixed so i took it for a drive, after about 3 miles it bogged down and i was able to make it home with half throttle going about 30mph. Sounds almost like its running on half the cylinders. i unplugged the ICP and it continued to run that way.
I had done the 50cent mod a few years back with the peices from ford but i know the harnesses themselves can wear through so i checked the resistance between the center pin and the two pins to the right and left for both the injector harness and they had about 3ohms.
I am leaning towards an IPR but from the reading i have done it seams like most trucks will not restart after they die. I have AE so i am going to hook it up later today, just wanted some reccomendations on what to look at.
I also remember when i shut it off the unplug the ICP to see if it would clear up the needles on the gauges did a full sweep as if i disconnected the battery which i though was weird.
View 14 Replies
i just bought my first diesel truck, a 7.3 of course. 2002 f350 4x4 crew cab, short bed. Any ways i drove it for like 2 weeks and left it at my uncles house so he can use to go to work. then 2 days later he calls me to tell me that the truck shut off while driving just like that. he tried turning it on a couple of times and it would just crank. he gave up and had it towed. I have been looking through all power strokes forums and found some solutions like changing the CPS or the IPR.
View 14 Replies
So I'm on my way out of town, when the truck just doesn't feel right. I proceed to make a u turn and pull off the high way. During the course of the u turn the truck shuts off. I pop the hood and notice the oil is everywhere from the fuel bowl back. Oil is also dripping off the passenger frame rail.
There is also a nice size puddle of oil pooled under the truck. I believe that I blew the high pressure oil line that feeds the injectors. I had to get towed back home. If it is the high pressure hose, how much does the stealership normally charge?
View 7 Replies
I have a 2002 f350 dually with a 7.3 and 197k. At 186k it died while driving and I had it towed home. As soon as the tow truck dropped it the truck fired right up like nothing was wrong. Then it died again 2 days later. I replaced the cps, but the fix was replacing the icp and pigtail. Now it is doing the same thing again. It died on my wife while driving yesterday, i had it towed to the dealership I work at and it started and ran for about 2 hours with no issues. I hooked up the factory IDS and had a diesel tech look at it with me. The oil pressure, injector circuit and injectors, and IPR all look good. The batteries were a little weak so i replaced both of them. I drove it home yesterday, about 10 miles, and drove it around town today. Then i tried to jump start my 96 bronco and after about 10 minutes of running it sort of hick uped then 5 minutes later it died and would not start. I let it set for 30 minutes and it started and died after about a minute.
View 2 Replies
I have a 2001 F350 7.3l diesel.
My truck died the other day while driving almost like he ran out of fuel. Well he had fuel so I checked the oil and it was dry. There was an ugly puddle between the intakes and a whole lot on the ground leaking out. Also the puddle looked blueish.
Put in more oil and got him home but I can't find the leak. The only thing I've noticed is that the intercooler on the cold side came off slightly. A year ago I had to go mess with the UCVH and when I put it back together I had lost a dang intercooler duct clamp and replaced it with a sturdy ring clamp. Well it wasn't sturdy enough.
How much would this leak if it came off for a little while and how serious of a problem would I have as a result? I don't have any check engine light and as long as he has oil he runs fine.
Since I have reconnected the intercooler and idle tested the truck I can't reproduce the leak. I don't believe that a huge amount of oil is running through that intercooler because the turbo is lubricated through another system I have read. So what gives?
Also I am getting weird dip stick reading. For a little while when I ran the truck today he was showing WAY over full on the dip and then down again a little bit below the operating range line. Also there are a lot of air bubbles on the dip stick when it comes up. Way more than I am used to seeing.
Also, I really like the idea of cleaning my engine off really good. It's a frigging mess now. What precautions can I take to clean it up good without making a huge mess. Can I just go the car wash that has a degreaser hose and drain and just spray it down like nothing or is it sensitive and finnicky when wet? Cleaning between the intakes seems almost impossible without getting the whole turbo system out of the way. Should I be thinking about that?
View 14 Replies
I have a 2002 f350 dually with a 7.3 and 197k. At 186k it died while driving and I had it towed home. As soon as the tow truck dropped it the truck fired right up like nothing was wrong. Then it died again 2 days later. I replaced the cps, but the fix was replacing the icp and pigtail. Now it is doing the same thing again. It died on my wife while driving yesterday, i had it towed to the dealership I work at and it started and ran for about 2 hours with no issues.
I hooked up the factory IDS and had a diesel tech look at it with me. The oil pressure, injector circuit and injectors, and IPR all look good. The batteries were a little weak so i replaced both of them. I drove it home yesterday, about 10 miles, and drove it around town today. Then i tried to jump start my 96 bronco and after about 10 minutes of running it sort of hick uped then 5 minutes later it died and would not start. I let it set for 30 minutes and it started and died after about a minute.
View 14 Replies
I have a 2002 f350 dually with a 7.3 and 197k. At 186k it died while driving and I had it towed home. As soon as the tow truck dropped it the truck fired right up like nothing was wrong. Then it died again 2 days later. I replaced the cps, but the fix was replacing the icp and pigtail. Now it is doing the same thing again. It died on my wife while driving yesterday, i had it towed to the dealership I work at and it started and ran for about 2 hours with no issues.
I hooked up the factory IDS and had a diesel tech look at it with me. The oil pressure, injector circuit and injectors, and IPR all look good. The batteries were a little weak so i replaced both of them. I drove it home yesterday, about 10 miles, and drove it around town today. Then i tried to jump start my 96 bronco and after about 10 minutes of running it sort of hick uped then 5 minutes later it died and would not start. I let it set for 30 minutes and it started and died after about a minute.
View 5 Replies
I have a 2003 F250 7.3L. I put new injectors in my truck four months ago and all of a sudden, I have 2 cylinders not working correctly, making the truck to run really badly. I sent the 2 injectors from the bad cylinders back for warranty and they replaced both of the injectors but nothing was wrong. I put them in and the truck still runs badly. I have a new fuel filter, new ICP, new CPS and glow plug relay. I cannot drive the truck, it smokes white at idle. I can unplug each injector at a time and cyclinder 5 does not change how the truck runs
View 14 Replies
I had an HPOP line burst and soak the engine compartment with oil. I replaced the line and degreased the engine and rinsed it off. I started the truck and let it idle for 15 minutes or so before driving it. On the way home right after a shift it started chugging and running terribly. The check engine light was on as well. I limped it the mile or so home and shut it off. I restarted it and it runs just fine. I checked the DTC's with Forscan and there were a bunch of things that were mostly related to the HPOP and the MAT sensor that was shredded when the line blew. I left the hood open to dry out today and I'm hoping it is just some water in a connector. Does that sound plausible?
View 6 Replies
I bought a 99 7.3 been in the trees for a few years pulled it home and now trying to get it running. Did a service new filters and oil fuel too. I can get it to start and will run but runs very rough and if you put it in drive cant pull its own self. I don't have a check eng light on. And found out my scanner is a pos lol. it will hooked up and then try to pull codes and loses it connection. But that's the scanner will not work on my other 7.3 as well.
I am making high pressure oil checked off the rail with gauge and it will build up to 2000 psi when I rev it. but missing like crazy. I swaped the pcm and idm out of my running 7.3 and it didn't change a thing. I have checked the pass though and they are fine. pulled drivers side valve cover off and no oil leaks when running and rockers are fine. new ipr valve as well too. I know I need to get a scanner to talk to this thing better.
View 3 Replies
I had been fighting some problems with injectors for several years. I didn't have time to dig into it. I knew what I needed to do, just needed to find time to do it. I honestly thought it was and injector and thought I would have to go to new sticks because I've had so many problems with the remans.
Well I finally had time last week. I pulled the passenger side valve cover and ohmed the injectors. It would be almost impossible to get the leads in the injector while installed the truck. I kept an old valve cover harness, so I cut a pig tail off of it and plugged it into the injectors so I could test. You can see the meter attached to the pigtail in the pic.
To my surprise all four were all right around 2.7 ohms. You need to set your meter so you are getting a reading w a decimal. If you set it to high it will only show a whole number and it is better to have a more accurate reading.
I then plugged the wiring harness back in and tested it from there. The #7 injector gave over 6 ohms. This told me that my wiring harness was bad. I went OE and replaced it. I had a problem w a Dormant valve cover gasket before so didn't want to go that route. After I replaced the gasket and harness all my readings were under 3 ohms. They were all lower than w the old harness.
View 4 Replies
So the last couple times I got a car wash the truck started running real rough, sometimes dies, then runs fine after a few minutes. Well, the last car wash I got it did it again, but the issue didn't go away. I checked the injector plugs, cleaned and greased, no change. Validated the bowl is filling with fuel, changed fuel filter, no luck.
Sometimes it will start and idle fine, rev in neutral fine, if you come off throttle abruptly it will fall below normal idle and start stumbling with an SES light and eventually die.
I managed to get it idling good, started logging with TPro (attached) and it was throwing codes P0475 - Exhaust Pressure Control Valve, and P0705 - Transmission Range Sensor Circuit Malfunction, as well as P1211, p1249, p1316 listed as 'multiple descriptions'.
I'm assuming this is an electrical issue since it happened after washing the truck, just not sure what sensor would cause all this?
View 14 Replies
I have a 99 f-250 with about 250k miles. Truck is completely stock. It recently has developed a problem where when I start it in the mornings it surges at idle, 200 rpm or so. Sometimes it tries to die and did once but started back up. When driving it continues to rev itself up and is jerky. It runs rough and sounds like it could be missing on a cylinder. At other times it runs fine just like normal. Yesterday morning it started with these symptoms so I put in a new ford CPS. It ran great for about 100 miles that afternoon. This morning it started back with the same symptoms. The SES light stayed on longer than normal when I started it, but it went off. I don't have a scanner.
I thought it might be water in the fuel because this started the day after I filled it from my transfer tank. But the water in fuel light has never came on. I put a new fuel filter on it but it made no difference. Have pulled filter three times looking for water but never found a drop. Also pulled several buckets from the bottom of my transfer tank but found no water there either. Where to look next?
View 5 Replies
