Ford 7.3L Power Stroke (1999-2003) :: Replacing Field Coil On A/C Compressor?
Jun 21, 2017
I have a 1999 F-250 SuperDuty with a 7.3L. I need to replace the field coil on my AC compressor due to a broken connector (long story). After I remove the belt and compressor clutch, what is the next step to get the pulley off so that I can then replace the field coil? I am a computer geek by trade so I need clear steps. I looked on youtube, but all I found was how to adjust or replace the compressor clutch or the entire compressor.
View 3 Replies
Advertisement
Upon trying to start my 2003 f250, it keeps blowing the 15A "Transmission Range Sensor then to Starter Relay Coil" fuse. Initially the truck would still start if i did not use the aftermarket Viper keyless start. however, now it doesn't start at all and keeps blowing fuses. I contacted the guy that installed the alarm thinking it might be something on his end. He walked me through reconnecting the factory starter wires which would isolate the issue if it was something on his end. it's still blowing fuses. battery terminals are good and clean.
View 3 Replies
im in the process of replacing the injector cups and i knew this would happen since the whole process went way to easy up until this part. I am using Clays remover kit and it will not remove the cup. I do it according to the book and it just keeps popping out of the cup when i try to remove
View 14 Replies
The next thing on my list of things to replace on my truck is the steering box. I have dealt with a lot of play on my steering for quite a while. I recently replaced the the ball joints and that worked but I think the box is just worn out. I have read all the great review on Redhead boxes but I just can't afford it now. What else is out there? Is our oem box a motorcraft or something else?
View 6 Replies
I have an 01 F-250 Powerstroke. It has been shaking terribly at around 1500 rpms and shutters while holding the brake and increasing engine speed. I took it to the dealer and they told me that my #1 injector is bad. I decided to check around a little bit. I found a diesel service dealer that has brand new injectors. (Not rebuilts). Anyway I would like to attempt to install this injector myself.
1. Which injector is #1? (I've done a lot of mechanic work but not a whole lot on engines.)
2. What do you do with the fuel and oil that get into the cylinder? Do you have to get it sucked out?
3. Anything else that is crucial? What do you have to torque the injector bolt to?
View 11 Replies
My 1999 F-350 7.3 is leaking from the turbo pedestool o-rings, from what my mechanic tells me. I would like to do this myself as it does not seem overly hard. This is my first diesel truck and am not quit sure how to do it. Looking for instructions or pointers on the process? I am a decent mechanic, but just have no clue on diesel engines and hoping to learn.
View 7 Replies
I need to replace the needle bearing in one of my hubs. I was wondering if the bearing needs pressed in or can it be hammered in with a large socket and a hammer?
View 2 Replies
I am doing some maintenance and trying to replace my EBP tube and sensor. I luckily have the dual alternator package, so getting the tube in and out has been a pain to say the least. I can't for the life of me get the tube back into place. As always, a 20 minute job is taking me 2 days.
View 14 Replies
I just bought a 99 F350 with 240k miles on it and got it for a deal because it needed injectors. Ive done the same job to my 97 OBS powerstroke. The injectors were already pulled so I had them sent for rebuild, the problem is I cant tell which injector goes where. is there a trick to figuring out where each injector goes when I put it back together?
View 4 Replies
I tried to replace the rear spring bushing of the drivers side front leaf spring.
Got the nutz off the shackle... The lower bolt was bumping into the front drive shaft and would not come out all the way.
Biggest problem I was having seemed to be I could not get the axle to drop far enough to release the pressure on the bolts in the shackle.
NOTE: I was trying to do this without unbolting the U-Bolts from the axle.
I was under the impression you could do this without unbolting the u-bolts. I have all new hyperflex suspension bushings and would like to get them on.
View 11 Replies
So again the a/c in old green gave out. it has been an ongoing battle over the past few years, but this time I took it to a good friend who has all the right tools as our level of frustration dealing with it has peaked.
We removed everything, and got it all "new" from oh-rye-lees. a new compressor was installed a few weeks back and it worked fine, but cycled very strangely. it would rapidly kick in and out, then just stay engaged. found out the condenser was plugged up and thought maybe that was causing it.
At any rate, it now has a new compressor, condenser, evaporator, drier, orifice tube, and low pressure switch. all the lines were flushed and checked.
it was vacuumed and checked, then charged with freon. The compressor is doing the exact same thing! it is cycling very strange. sometimes rapidly at higher rpm, and sometimes it works just fine. the a/c is working, but it is freezing up the drier, evaporator, and line all the way back to the compressor. vent temps are about 30.
The WOT relay and high pressure switch was replaced, and it did not make a difference. we are at a total loss.
We were told by another person that the clutch on the new compressor was too small and that was causing the issue. It measure 4.8" and we were told is is supposed to be 5.3". is there any truth to that? we just do not know what is causing this, but want to get it right as surely something will break if it stays this way.
View 6 Replies
SO after reading about the air gap on AC compressor, i checked mine and it was large so I removed the shim and the gap was almost like new..
Now when I first switch on AC the compressor will click on and off several times especially at any RPM above 1000.
I hooked up hoses and tried it again with wife holding RPM in 1200. The high side would bounce from 100 to 400, compressor would cycle off and then back on in quick secession with high side bouncing back and forth for 10 seconds or if she let off pedal back to idle RPM.. low side was not moving a lot at this point but not bouncing like the high side. What can be causing the pressure issue? when it stabilizes the pressures are right on for OD temp according to charging chart for R-134a.
View 14 Replies
2003 7.3, AC compressor clicks like crazy. Can he hear outside the vehicle while idling?
The round disc on the front of it is what is making the noise.
The AC used to work awesome but now only blows cool air for about 10 minutes then turns lukewarm.
Is the clutch on my compressor bad? I have heard they can be adjusted, but not sure how.
View 6 Replies
Alternator locked up in a parking lot. Replaced it and had to replace pigtail due to a loose wire in the harness. Now battery light comes on intermittently. New alternator is doing fine producing anywhere from 13.9v to. 14.4v. No output voltage correlation to battery light at all. The belt is still in great shape so I don't suspect slipping. Fortunately I caught the old one locking up almost immediately and had recently replaced the belt. Output voltage looks great. Are there any fuses for alternator?
Only thing I can think of that I did...when splicing in the pigtail that connects to the alternator, I briefly grounded whatever wire in the pigtail is hot. Was just a split second, but enough to see a spark and maybe enough to blow a fuse? I've seen people reference an "under hood" fuse box, but I don't seem to have one. My truck is a 2002 CC with just over 100k on the clock.
View 3 Replies
I was getting a growl/grinding noise from my front hubs (driver's side I think) when I do a slight right turn like going around a curve, not turning around a corner. Just started happening the last week after returning from a 4th of July roadtrip. First thought was wheel bearings going out and started reading up on the forum here to see what was needed. Last night, I started getting a continuous growl when I was 5 miles from the house so just pulled up and parked it. I'm assuming (without pulling anything apart), it's the bearing assembly and I can get the Timken version at Autozone locally.
The problem is I generally do my heavy maintenance at our family shop in San Antonio but I live in Austin so will need to do this in my driveway. I have all the basic tools, just need to know how involved it is to do in a driveway instead of a shop. Thoughts?
View 14 Replies
I am looking for a how to vid or resource on doing the job right. I purchased the complete replacement master cylinder from Napa. 2002 7.3 Powerstroke
View 3 Replies
Was wondering if the wheel for the ported housing from riffraff is worth it. Also, since I'm lazy I was gonna just spin the old wheel off with an impact wrench. I have a cordless that's prett stout but I'm sure I'll have to use air. Any thoughts on the wheel and taking the stocker off this way?
View 14 Replies
Trying to replace a right rear door handle on my 01 7.3. Attached is a photo of the new handle with the unlock rod. Also is attached is photos of the door without handle. I pointed to the part that moves the lack to unlock.
Looking for the clip part number or photo that is missing. I thought a hose clamp would work maybe with a nut on the rod?
View 6 Replies
On 2500 mile trip, no A/C last 400 miles and we're cooking
Compressor clicking on/off about every 5 secs, clutch smell. Seems to be turning okay.
I brought some tools, including a full socket set.
Can I pull the clutch and remove shims in the campground? Looking for a condensed version of how?
Worst case, how do I replace the clutch- of I can find a dealer with one?
Pulley and clutch fixed, but cycling on and off...adding freon?
View 14 Replies
I have search youtube and only found front door lock replacement but not the rear..
How do you go about removing the bad rear passenger side door lock actuator ??
View 14 Replies
I blocked off the hpop discharge tube to test for leaks, shop air. I am plugged into the oil rail drivers side, and keep getting a slight popping sound. The first time I did this it took ten minutes to start, so I replaced the top injector seals. The second time it did this after about four minutes, so I took the oil rail to the local shop and they did the ball tube orings in the rail, now I went to put it back on and it does it almost right away.
Am I just pushing the oil out of the injectors? is this normal or should I have NO air noise period? I guess I am not sure how these injectors work, where does the oil go after it enters the top of the injector? It seems like it's coming more from the top coil area, more so perhaps than under the oil rail.
View 6 Replies
