Trying to be proactive seems to have backfired on me. What to do? Pull sensors and clean? Checked codes points to both left and right sides.
View 14 RepliesOk so i have an 02 F350 7.3 with 89k on it ... Ive had the truck about 2 years now and ever since i bought it the ABS light has been on. So finally i got to scanning it and codes popped up for the front speed sensors and the rear speed sensor. So i went ahead and just put all new MOOG hub assemblies in the truck which come with the speed sensor already in the them and i also replaced the rear speed sensor, which was difficult!!! Becuase the bolt was seized and i ended up have to drill and tap a new one and even then the sensor seats in the hole in the diff but doesn't seat flush with the housing if you really tighten it down, and it leaked a little fluid at first but i ended up loosening up the bolt a little to make it seat better and then i put silicone around the bottom of the sensor and it stopped leaking... Anyway I've fixed both the code issues and cleared them, BUT, the rear speed sensor code pops back up immediately after clearing it and the ABS light on my dash stays lit .... Idk what to do at this point because I've fixed everything and it still pops the code for the rear sensor, I just want the Light on my dash to go off thats all ! ...
View 6 RepliesWhy the heck would my dome lights (front and back) stay on while I'm driving and when the truck is off KOEO and locked? It's not the reading lights, those I can turn on and off at the switch on the light, it's the lights in between them.
View 10 Replieslong time ago i had to change master cylinder and the calipers on the fronts and the break fluid well i decided to test it out and see if they were working fter i was done with them then the light on the dash came on i thought its because the floating thing in the master cylinder was not floating which was not the case i dont think its the sensor i also lost my emergency break shoes never replaced em
01 f250 2wd 7.3l v8 diesel straight pipe 310,xxx
Here are some signs of the problem.
*Key fob does not work - battery is good.
*Interior overhead light works only on manual.
*Driver's auto door lock (with driver door open) will lock all four doors but the driver's door will automatically open back. To secure the truck I manually lock the driver's door.
*I replaced the driver's door 'ajar switch' with no results. The old switch was good after testing - normally closed until the ball is depressed then it goes to open.
*No codes.
*I just checked all the mini-fuses with a VOM and they are good.
*Could one of the relays be part of the problem?
I am curious if there is a scanner that can identify the bad door ajar switch if any?
From what I have read so far it appears the VSM (Vehicle Security Module) may be bad as a many of these 2002's complain of this problem and the VSM generally solves the issues. Are there folks other than the dealerships that can program the module if I purchase a new one and remove the old OEM one? Other than the inconvenience the truck runs fine other wise.
Auto trans. The Overdrive light flashes on the Selector lever. Never stops.I put tape over it because it is annoying. Especially at night. It goes into overdrive no problem.
A Couple of times it did not flash and was stuck in first till I manually shifted. Then the light started flashing again and works normal. What now......RPM Sensor?
I've read a few things on the 4R100 and have a question.
My transmission stays in the OD off position until I hit 55 mph no matter the tune I am using and then will up shift to OD. It turns back off once I drop below 30 mph.
I was told when I bought the truck that it was a factory tow package. Is this a thing?
I would like an option to turn it off when I'm not towing or climbing a hill if I can.
Any way to modify it with a switch?
Two years ago I acquired a very very nice 2001 F350 DRW crew cab. The person I purchased it from put a Remanufactured 7.3 in it and set the truck up to pull wedge trailers. He put 25K miles on it and put it on Craig's list where I found it. It just turned over 300,000 miles.
One of the changes he made was to install a 70 gallon fuel tank in the frame rails below the bed. He told me that when the gauge reads EMPTY there is still 20 gallons in the tank. I remember him telling me that this anomaly is due to using the stock Ford pickup in the larger tank.
I have never filled the tank because so far the truck is used locally. I usually put 10 to 20 gallons in and when it gets to E I do the same fueling.
Then one day I turned the key on and the needle went up and beyond the full indication.
I can get under it and maybe the tank has some name or model number on it.
The truck runs fine, but the gauge concerns me. Eventually the truck will be making round trips from Chicago to our retirement home in Santa Fe, NM. It would be nice to have a working fuel gauge!
I have spoken to the person I purchased the truck from. He installed the tank as part of a complete upgrade that included a re-manufactured 7.3. The fuel tank is a 67 gallon Titan mounted between the frame rails. He believes that the original Ford sending unit was installed. That means it has 300,000 miles on it. I had the truck on a lift yesterday and it is a very tight fit. The garage said the best way to do the repair is to remove the bed. Six bolts, disconnect the tail lights and the 7 pin trailer connector and it is off.
So, my questions now are... Should I stay with a new Ford sending unit or are there better ones to install? Are there any other updates to the fuel delivery system that should or could be done at the time?
I just had a remote start installed with a turbo timer that works off of the parking brake being engaged. No matter how hard I press it the light does not go on, however when the installer probed the sensor to ground it, it worked fine.What part this is that needs to be replaced. The stealership quoted me at 200 something for a whole parking brake assembly.
View 14 Repliesmy 2003 f-250 4x4 6.0 engine service light stays on all the time (for about 2 weeks now) it has 33,323 miles on it. it is running fine-no problems yet. no codes are showing up on a diagnostic test. What is going on?
View 10 Repliesi have a 99 f250 7.3 powerstroke. the cam sensor was acting up. that what the scan tool said. i replaced the cam position sensor yesterday, and the truck is still acting up. the motor hitches and will shut off randomly. it tripped the check engine light, and the code is the "cam position sensor" once the truck is warmed up and shut down for like 10 minutes the sensor will not act up anymore. if i just start the truck and run it, even once it is up to tempature it will act up. but if i shut the truck down for about 10 minutes, it goes away. is there something else that could be causing this?
View 14 RepliesI have an new to me 1999 4x4 F350 that I was giving a good once over today on the front end since it wanders a little bit. but anyways I didnt see a abs sensor wire on the front. the plugs are there behind the inner fender well and it looks like there is a plug when the sensor should go in the wheel bearing. was 2 wheel abs an option on these trucks? is there anything else this changes front end wise?
View 14 RepliesI have a 2002 F-250 7.3L with 175,000 miles and it died on me July 30th. Here were the symptoms when it died:
Engine was sluggish at standard RPM about 1300-1500 going about 45 MPH, so I stepped on the gas and it seemed to go away. About another 5 miles down the road and starting from a stop, the same thing started happening. The entire truck seemed like it was going to shake itself apart and with the peddle at half throttle it revved to 3500 rpm and didn't shift into 2nd gear until after about 5 seconds at that RPM. After it jerked into 2nd gear the engine dropped back down to about 1000 RPM and started shaking violently again. At this point I managed to make it to a shopping center and then as soon as I let off the gas (still shaking), the engine dropped to 500 RPM and after about 15-30 seconds shut off. When I got the truck home I managed to start it one more time but it shortly stalled after about 15-30 seconds, again it was hovering around 500 RPM and still shaking badly.
Here is what happens when I try to start it:
From 0-2 seconds, truck goes through a normal cranking rhythm and sound.
From 2-10 seconds, it slowly tries to start itself back up but it sounds like it is only firing on a few cylinders, I'm guessing maybe 2-3.
I stopped after 10 seconds in fear of burning out the starter or killing the batteries.
Troubleshooting:
Removing the connection to the ICP sensor, something I read that might at least let me start the truck, which is how I found the oil on the connection itself. I also noticed a little bit of what looks like oil on the some of the wiring harnesses in the surrounding area. I also checked the fuel bowl and it is filled with fuel.
Possible solutions?:
From what I have read on the forums I am guessing that it has something to do with the ICP or the IPR sensors. I also believe that it is a sensor related issue considering that the truck won't even start. I am completely off track. I am going to start working on it full stride this weekend. I have been vehicle-less since the 30th so I'm trying to get this fixed asap. I don't have any codes, I am going to try to get a coder this weekend.
I am doing some maintenance and trying to replace my EBP tube and sensor. I luckily have the dual alternator package, so getting the tube in and out has been a pain to say the least. I can't for the life of me get the tube back into place. As always, a 20 minute job is taking me 2 days.
View 14 RepliesNoticed a while back that the plug for what I assume is the air intake temp sensor is looped. I assume because I can't find the sensor anywhere. how critical is the sensor? The new S&B has a hole for it so it's either gonna need a new sensor or a plug. The local autozone has one for 16.99.
View 12 RepliesI need to install an oil pressure sensor sending unit. I've already occupied the 1/8"NPT test port on the rear of the oil cooler, where else might I be able to tap into oil pressure? (LPOP)
View 4 RepliesFor some reason my OH display decided to show 140 deg F when its 40 deg F outside. Continues to show 140 all the time now regardless of out side temp. In case its the related outside temp sensor sending unit, where it is exactly on an 02. Unless someone has solution may try changing that out to see if that is the problem?
View 14 RepliesMy 2000 F350 7.3 has been stalling out with the water in fuel sensor for the last to tanks of fuel. I thought I needed to buy a new Titan fuel tank, I pulled the tank and was surprised to see that my tank was not a metal tank, It's polyethylene, I bought the truck in California with 60,000 miles it has 180,000 miles now. It was sold new in Canada, I expected the tank to be metal with the the liner coming off.
The two fuel filters in the tank are just about plugged solid I'll be removing them and repiping the return line. When I repipe the return line do I put the duck bill on the end or just leave it open? Also I searched the web for hours looking for a stock size polyethylene tank with no luck. On the bottom of the tank I found The ford part #s. I'm going to siphon the fuel out of the tank today. and reinstall....
I drove my 99.5 7.3 F-350 1 mile to a friends and hooked it to the OBDII to get a code for my abs light.it had not been drove all day. we hooked into the pcm and he noticed the temp at 375* it was idling. is this right he didnt think it should have been that high???Will the engine coolant temp sensor, if it were bad,show a high temp of 375*? On the OBDII it showed a temp of 375* .....
View 14 RepliesOk I have a p0197 engine oil sensor low.. Temperature is cold right now and truck was not plugged in.. Truck surges when started unless I give some steady throttle and oil warms up. Also service engine soon light comes on.. Oil change soon but been a while.
View 9 RepliesWhat the sensor is for? In the course of removing the rough country bumper from my truck and installing the 2005-2007 factory front end I found this guy hanging out with wires cut. I haven't attempted to wire it back up because I want to know what it is first. It would appear that the sensor is suppose to be screwed in to something.
View 5 Replies