I have developed an oil leak from the bottom of the front crank shaft (front of the motor). How hard of a repair is this? any links to any tutorials? Should I even try this myself? Any special tools required?
View 14 RepliesCan I re-use this shaft or is that ring around it no good. The ring is around where the bearing sits. It is a circumferential hump all the way around.
View 14 RepliesKind of bummed my truck now leaks oil from both the front and back. It's not much volume wise - probably a pint every couple months but before I came up to Alaska it had never leaked a drop. Probably nothing I can do about it barring a rebuild. I have noticed all the guys say not to use any oil additives of any kind. Trying to get it in a shape for another epic journey back down the Alcan highway this fall. Or should I get rid of it and go for a 6.7.
View 10 RepliesMy 7.3 has a leak on the front diff passenger side. It went into a shop for repair and they did both seal but the passenger side came out with a worse leak than it went in with. So just looked this morning and small pool of oil under the ujoint area on the concrete. Its booked in again to be fixed under warranty repair (place that fixed it, repair came with 2yr warranty) on Wednesday next week - was the earliest I could get.
Question - can i keep driving the truck? I'm making a wild assumption that I can unless I use 4 wheel drive. My intention was to just keep topping up the diff to ensure there is fluid in it. It's the work truck so wouldn't be good to be without....
2003 F250 7.3... I noticed a water leak dripping down onto passenger side front leaf spring. I saw this before but attributed it to the AC (which kicks butt) but haven't used the AC. No scent to the clear fluid, temps all look good. Running fine. Where does the AC discharge go? Could AC be on (not on AC but set in blue zone on dial)? Reservoir looks ok but could e small volume of drips.
View 12 RepliesWhat Spicer Part #s for the rear u-joints would be? I'm not nailing down the right one. I keep finding numerous ones, 1410, 1350, 5-160....
View 8 RepliesI'm trying to replace my transmission output shaft seal on my 2wd and I can't seem to get the seal removed. I couldn't find anything to rent from O'rielly's or Advance Autoparts that would work. It's in there really tight ....
View 10 RepliesCheck out the pics. 99 f250 4x4. I have a leak in my front axle shaft. It looks like it is coming out of the dust cap on the end of the front shaft. I am pretty sure it is differential fluid from the smell. Is there a seal before the dust cap? Is the shaft hollow with fluid in it? I thought it was just in the differential and if it leaks it is at the seals where the axle goes into the differential not at the otter end.
View 2 RepliesCheck out the pics. 99 f250 4x4. I have a leak in my front axle shaft. It looks like it is coming out of the dust cap on the end of the front shaft. I am pretty sure it is differential fluid from the smell. Is there a seal before the dust cap? Is the shaft hollow with fluid in it? I thought it was just in the differential and if it leaks it is at the seals where the axle goes into the differential not at the otter end.
View 14 RepliesI bought this truck an it ran good then one day it started knocking really bad so i replaced the crank shaft an bearings. Put everything back together started the truck an it ran like crap an i just happened to check the oil an it is milky. All the water in y radiator is now in the motor oil an truck has no power...
View 2 RepliesIam looking at a 2000 7.3 Powerstroke that has some problems first it is hard to start cranks like it has a dead cyl. Second after starting it has no power not even enough to move. At first it would only run if held wide open but once it warmed up it would idle and rev and move but barely still had a miss. The weird thing is it did not smoke blue-black or white also no strong smell of diesel and no smell of oil at all. The truck has 230ish miles and there are no maintenance records.air filter was new.
View 7 RepliesI have a e99 f350 7.3 all stock. I have no power. The truck will crank for about 15-20sec before it'll turn over. I just purchased the*AE*but am fairly new to understanding it all. In idle its a little rough and when I drive I can only stay in the neighborhood because of fear of getting rearended due to very slow acceleration. Whats weird is that when i have no power while i am driving ill keep the pedal down throw it in nuetral and my rpms and*icp*pressure jump up right away. Things I've replaced:
Icp*sensor
Fuel pump
Pcm
Tps
Cps
Ipr
Dropped tanked and cleaned screens
When cranking my*icp*pressure climbs slowly to right under 500. I dont know what else to do ive been working on this truck dor two months some days 13hs straight, I am feeling defeated. Codes p1249 1211 1209....
I have a 1999 7.3 super duty that won't crank when the key is turned. All lights work, power windows and mirrors work but after the WTS light goes out... Nothing...now I do have a slight leak in the roof and a little water does get in the cab. I opened my door the other day and it smelled like an electrical fire had occurred. I checked under the hood and the same smell, if not a little stronger. I pulled my fuse box and GEM tonight. Once I got away from the truck, I expected them to smell like the electrical fire smell, but they didn't. Now I did try cranking the engine over by jumping the starter relay before tearing the fuse panel out, and I got it to crank, but not strong at all. The batteries are good.
View 11 RepliesStarted truck 3 times in 30 min. no issues with truck before tonight nice well cared for truck. Went to get a pack of buns at store came out --NO CRANK--all lights are on dash, etc, new starter a month ago, relay changed out in fuse panel just to see if there was a change. Bought two new Motorcraft batteries installed , NO CHANGE, so is it natural safety, key switch, electrical ignition switch, solenoid on starter, is there a solenoid between key and starter?
View 12 RepliesNew to the forums, not new to fords. 1999 F350 7.3L Diesel. This has been a work truck and has seen multiple devices in and out over the years. I removed the last crap for GPS tracking etc from the last owners. The truck has worked well for a long time since until...
I'm moving slowly to a different state and so the truck got parked for 2 months. went to start it and nothing. the dash comes on and all the lights come on but when you turn the key to start the power drops and nothing.
Testing so far:
replaced the fender Solenoid
tested the starter motor and solenoid -passed
replaced the ignition switch
tested continuity of the hot and ground wires to the fender and starter and everything passed
When I shorted across the fender solenoid the starter works and tries to start the truck (unsuccessfully so far)
So the wire that goes to the fender solenoid is not working and where to trace it to and what needs to be fixed. Is there a relay or fuse besides number 30 that is in the way? where does the magical wire go so i can check its continuity?
I am stuck 800 miles from where i need to be and I am stuck here. I don't have the cash to get a mechanic and my mechanic friends are stumped. I do have a Snapon modus tester, what to do with it.
FYI the batteries are new and fully charged.
I just see a fluid by the front passenger tire leak when the diesel is running and ac is on.There was fluid up by both aluminum lines going into a plastic canister in the engine compartment on the passenger side.I couldn't find any cracks in the hoses or aluminum lines..The plastic canister I believe is (AC ACCUMULATOR ) did have a hiss of air when I shut the truck off. I can't see where the clear liquid is coming from. Just started to leak by the front passenger tire.
View 3 RepliesOn the way to work, the truck seemed to have a miss at idle and the CE light came on. Long crank to start leaving work, and truck starts losing power and eventually died. No smoke while it was losing power. Towed it home and checked the fuel pump and lines for blockage and found nothing.
2003 7.3 F-250 430K miles
strong cranking but no start no smoke out exhaust
Oil changed recently
IPR changed
Both UVCH gaskets and pigtails have been repaired.
ICP sensor and harness changed, also disconnected no change in cranking.
fuel filter changed today (no oil in bowl)
3/4 tank of fuel
dash gauge for lpop goes up to normal range during cranking and oil light turns off.
WTS light comes on and turns off as normal
tach gauge moves up between 100-200 during cranking
fuel pump turns on and pressurizes system like normal and turns off.
Ordered AE for the truck, and it directed me to the passenger side bank high open. Fixed the harness on that side and still nothing.
Sent off the IDM and it passed with flying colors
So now i'm leaning towards the HPOP, but would hate to fork over the cash for it and still not get anywhere. I'm going to take the valve covers back off and check the discharge ports for the injectors tomorrow.
I have an 02 f250 230,000, first 7.3. I've owned it since Oct and put less than 6,000 miles on it. I have another cold crank no start. New glow plugs and Glow plug relay last weekend. Worked fine that weekend. It sat all week, then crank no start fri night, it was like 70 degrees for the high that day. Plugged it in over night and it started. Did not fire right up cranked it for a couple seconds. I drove it all day, started every time. Valve covers have 5,000 miles on them. Fuel Filter heater fuse not blown. But don't know how to check it for sure. And don't know where to go with it from here. Getting frustrated with crank no starts. No troubles found.
View 2 Replies I got a 2000 7.3l with 400,000 miles on it that decided to just not start anymore after I parked it for a couple days. Its always been a hard starter due to needing glow plugs but I can deal with that. it doesn't even try to fire anymore. I replaced the CPS (my tack bounces when cranking). The ICP has oil in the plug so I just unplugged it for now till I replace it.
I pulled the IPR and cleaned it really good and bench tested it with 12 volts and could here it clicking so I put it back in. I can get under the drivers door with the key on and hear the fuel pump running. I gain oil pressure on my dash gauge when cranking. I check all my fuses. my WTS light comes on . I just don't have any fancy scan tools to make this easier. Also just cause I was feeling lucky I just went out and bought 2 new batteries for it yesterday so we are good there.
I have a 1997 F350 7.3 with standard xmission. Have not messed with it since Oct of last year. Then it would crank but no start. Now when I turn the key there is no wts or nothing the gauges move, and tach moves when cranking, but nothing else.
The cam and crank pos sensors have been changed. The high pressure sensors changed. Now when I hook it to the AE it says cannot connect to truck. Where I need to start? Have checked all fuses that I know about.
Friend's 2000 7.3 wont start, just crank and crank tried to fire but nothing in the cold leave it plugged in and it starts leave it in a shop over night and it starts with a shot of either, he is a truck driver and the truck will sometimes sits for 6 weeks at a time this time 2 weeks before I touched it. He wanted me to install a fuel pump so I did and started the following:
Cracked fuel lines to see if I had fuel psi at both heads
I tested glowplugs they all read at 0.3 on all 8
I have power to harness as the same at both sides of the relay
RPM tach jumps
Oil psi gauge rises
Using my phone I can read hpop and 2000 at cranking (how accurate that is im not 100% sure)
All fuses good