My coolant bottle, as well as my entire engine compartment, is full of oil. The truck won't run. It will make ICP when I first crank it but then it goes away. I have the orings and gaskets to do the oil cooler, it is there any chance there's something else that caused this? Anyway to diagnose the oil cooler before I disassemble?
View 4 RepliesAs explained in the photo annotations, I can't figure out how to remove this line from the radiator so I can remove the radiator for cleaning.
View 7 RepliesSwapped a new oil cooler and welded Egr shut. Truck ran fine the first 3-4 times I started it except for exhaust leak at the y-pipe/turbo connection. Tried to start it today and it started then ran real rough, blowing whit smoke. Now it will not start at all and blows whit smoke. The only codes I'm getting are egr codes that I've always had due to having the 05 and up intake elbow and the egr turned off via sct. What could be the issue?
View 8 RepliesI bought a 2003 F250 7.3 Powerstroke from a buddy of mine with 99,500 miles. It is a former Michigan truck and has some significant rust issues. Oil pan and drivers door will need to be replaced in the not too distant future. And probably bed rails later too.
In any case, I noticed a puddle of tranny fluid on the driveway when I got home today. The passenger side line at the fitting into the bottom of the radiator has corroded through. The fitting into the radiator is pretty rusty, and the line fitting is darn near destroyed. The line itself actually has a hole in it.
I see the same part numbers on different sites with different descriptions. Driver side here, passenger side there, inlet here, outlet there. For the same number.
As near as I can tell, Dorman number 624-059 is the outlet line from the tranny to the passenger side radiator fitting, and should be the part I need. Correct? Dorman 624-058 seems to be the line from the OTA auxiliary cooler and back to the tranny. What I cant find is the line from driver side radiator to the OTA cooler. That fitting is corroded bad too, and I may as well do both of them.
So changing the oil in my truck the other day, I noticed the exhaust clamp at the union between my down pipe and first section of my exhaust has been rubbing the trans cooler line and there's a Nick in the granny pan. Lookin at the rubber grommet on the hanger, its stretched tight and looks like the exhaust has shifted over. What could have done this or possible fixes?right by now it's got a gob of high temp silicone acting as a stand off. Don't wanna put the new line in until I have the situation remedied.
View 10 RepliesI've had my early 99 f350 7.3L for a lil while now. Starting to see few problems surfacing. while doing my weekly fluid levels found oil in coolant and after looking around found oil covering bottom of driver side engine. As far as i can see it looks like oil cooler leaking from front side.. Should i just replace oil cooler or rebuild?
View 4 RepliesDoing oil cooler. Block heater plug is very tight. Is it reversed threaten?
View 1 RepliesI have a leak in my inter-cooler system. I have replaced all the hoses. Is there a reason I should not pressure test the system with 20psi? 2001 F350 7.3 turbo
View 4 RepliesLast November I forgot to plug my truck in and it got down to 0, my girlfriend tried unsuccessfully to jump start it. When I got home I jumped it and got it running. I took it down to a heated shop to troubleshoot the glow plug circuit. I discovered it was not getting 12v to the glow plug relay. Also I started it and tried to back it up in the shop, when put in reverse it killed the engine, not lugged it down it was like you shut the switch off.
Also I discovered if you turn the lights on it kills the engine immediately. It will not crank with the lights on either. So far I have replaced the computer,ignition switch,batteries, and cam positioning sensor. Now comes the weird part!! I decided to get it running and pull the bulbs out of the back up lights I pulled the drivers bulb first then the passengers side bulb. When I pulled the passengers side bulb it killed the engine.
It is not my daily driver so it still sits in my shop. I have a hunch it's a ground issue but I've checked and cleaned up all the grounds I can find and it still has the problem.
So on my way home today I lost all power, the engine shut of and i coasted to side of the road. Went to try and start, nothing. When key is in the crank position the gauges were jumping all over the place, also accompanied by a lot of clicking from behind the dash. Nothing happened when tried to crank. No power to windows or even emergency flashers.
So i get it towed home, and of course it turns over. But this only lasts about ten seconds, then dies. I could do that a few times and then back to no power at all. Even at times with the keys out of ignition it will still click and make a lot of noise.
My 99 E350 with 7.3 power stroke quickly lost power while on the highway today, bogged down and died. I couldn't get it restarted so had to have it towed home. I tried getting it started at home but it just pumps out white smoke out the exhaust. I got it to fire and run for a minute on a mixture of starting fluid and wd40 but wont stay running. Some background info, I checked oil and it was low but still registered at very tip of dipstick so I topped off oil level and still no start unless I give it a mixture of starting fluid and wd40. Batteries are good and cranking fast. Truck has 355,000 miles but very little blow by and prior to this had plenty of power and didn't have to use the block heater to start it thru the winter even when the temps dropped down to 12 degrees in January.
One thing I did have an issue with this past year was an intermittent cutting out while driving where the engine would instantly shut off but as soon as I tapped accelerator pedal it would start running again like nothing happened, wouldn't even last two seconds and it was running again just like shutting off the key and turning it back on and when it would do that the "Wait to start" light would come on and gauges would drop like key was off but again it all went back normal as soon as I hit a bump or tapped the accelerator pedal and it never lasted more than a second or two and never had to pull over, just tap the pedal or hit a bump and engine would kick in and run fine so not sure if that's related to whats going on now or not.
Lately I had a couple glitches seemingly unrelated with this electrical system. Something just failed. I have two new motor craft batteries cleaned all wires/ clamps. The alternator has been tested good. The other morning I started my truck and smelt a wire burning up before I took off. Battery positive to glow plug relay was hot. The solenoid was junk so I replaced it. Still not the problem. With the battery positive hooked to the solenoid, truck will not shut off. It will shut off by key if the wire is unhooked. I do know this. When hooked up, the battery positive is feeding voltage (.4v) through a new solenoid to the PCM, thus keeping the pcm life when the key goes off. Bad pcm? With the battery positive hooked up to the glow plug solenoid. There is such a large draw that the charging system cannot keep up. Wich out me on The side of the interstate at 1 am as I watched my lights grow dimmer til truck stalled. U hooked the battery positive from solenoid got a jump and been fine since....however, there's a major problem lying there right?
View 8 RepliesI have a 2001 F350 7.3 the truck will at random times loose power and almost shut down. A while back I had an issue with the uvch plugs and changed that out. Truck ran fine till I got some dirty fuel from a diesel tank at my friends farm. I did the hutch mod cleaned the tank and now have a frame mounted screw on filter before the pump. I cleaned the fuel bowl and changed the filter. Fuel pressure stays at 59psi and drops to 56psi wot. The truck is tuned with an edge programmer. After these mods the truck ran awesome for over 2000 miles. Now it has the above stated problem. I have fuel and hpop guages along with egt and boost. During the problem egts will increase rapidly and it seems like it is starving for fuel.
Hpop gauge reads 3300psi or above during wot and shows good pressure during these mishaps. I have auto Enginuity and I get a different reading at wot of only 2600 psi. The hpop gauge is tapped into the icp sensor per instructions and has been installed this way for a while with no issues. The tune has been on the truck for over 40000 miles. The only thing that I can come up with is it will occasionally throw a p1211 under wot or pulling my Gooseneck Dump Trailer when loaded. However it acts up sometimes and doesn't throw the code. Sometimes you can shut it off and start it back up and it's fine other times it will last for the whole day. My only guess is low pressure from the hpop but I don't reflect this from my gauge only on AE at wot. Wouldn't a bad pump act up all the time? Am I correct to think it is just the ipr?
I have a 99 F 250 7.3. It runs fine at idle even for a long time. When I drive around the block a couple of times it will start chugging and lose power and shut off. I have been mixing fryer oil with the diesel. I changed the fuel filter, oil change, crank sensor and fuel pump. I added 15 gallons of diesel and diesel treatment. Pulled fuel filter and bowel is full I'm not sure where to look next.
View 1 RepliesMy truck occasionally gets a hot no start issue and it's been happening more frequently. Mostly it happens if I drive it up to operating temp turn it off for a short time, then try to start up again. Usually, if I wait 15min to an hour it will start up. It has died on me while driving too, then I have to wait and periodically try it. I've noticed in this situation that if my glow plugs turn on for only a short time, it won't start. But once the motor has cooled enough that the glow plugs stay on for the longer duration, then it will start right up.
I've replaced the CPS, rebuilt the IPR, did the ICP unplug test, rebuilt the injectors, replaced the fuel filter.
HPOP oil level is good, changed the oil maybe 500mi ago. When it's a no start, the low oil pressure gauge does start to read after some cranking, also the tach does read. It throws no DTCs. My reader isn't able to monitor live sensor data.
There is some oil in the valley, but I can't find the source. I think it's probably the turbo pedestal. What else should I check?
Ok after rebuilding trans and being down a couple of weeks, I went on my 1st run since completing. Noticed when I started truck this morning it didn't turn over as fast as it was. 30 miles down the road Airbag Light comes on, and then volt meter dropped to 8 volts. Got stopped with truck still idling checked everything I had the tools to do so for. Decided to get back to my shop where I had tools, and 5 more miles and 55 mph truck just shuts off. Lost all power, truck would only click. Put my booster box on battery and gauges went back to normal but still wouldn't turn over but maybe once? Only place within a mile of my location was Walmart. Bought 2 new group 65 batteries, installed them and Shazam cranked right up no more problems. Short of the story bad batteries that checked Good with a load tester don't mean squat!
View 10 RepliesTruck is an early 1999 F250 Super Duty ext cab long bed, ZF6 swap. 164k miles on the dash, has the newer injectors and hpop from what I was told. It does have a 6 position switch, I typically keep it at the daily 70 horse gain tune. I do not beat the truck often. I don't tow often either.
Truck always took a few seconds longer to start than other 7.3s I have seen. So two days in row, after 8 hours of sitting in the sun, my truck did not wanna start right. Took about 5 minutes of cranking both days to get it to start. Then today on my way to work in the morning I started truck let it idle, everything seemed fine, Started driving and the engine just didn't sound right, but I figured maybe it was still a little cold. Continued driving, and it stalled out ( zf6) , I tried pop starting it but that only got me another block or two, after 10 minutes of cranking I got it to start up made it a half mile it shut off, same thing started and got it home. It cranked longer than normal but started at home after it I turned it off.
At work now so I have yet to check anything. Replacing CPS after work No smoke out of tailpipe, It is getting fuel, I checked the filter. I am no master mechanic, I do basic maintenance like oil changes, brakes, filters and censors my self. Anything more intensive I have not done. If it is not the CPS what else could it be, and how would I go about checking?
E99 zf6 180k. Ts 6 position and 6637. Just found d out the oil was 25000 miles old and changed it. 400 mile trip followed by a few days in town with no problems. Shut it off warm and it won't refire. Takes 3 loooong cranks. Few minutes later it restarts hard but not as hard. Head out for a few hundred mile trip and it's running fine except all of a sudden "bucks" a few times within a couple hour window. I took data during the trip and never saw anything strange. Today a cold start, around town driving, and warm restart were all normal.
My thoughts are to
1. Verify steady fuel pressure (I only have a temporary gauge setup)
2. Check the fuel filter for oil.
3. Pull the valve covers to look for injector oil leaks.
#3, though, I dunno if it's worth it. Perdels look fine and icp seems to be about the same as it always has.
I have a 04 that has 153k on it. 4" cat back exhaust with no cat. SCT tuner running a custom street tune. New FMIC with the extra tune on it. Head gaskets where done at 90k along with ARP studs. EGR cooler, The oil cooler was cleaned, New coolant tank. 1-new head and The cooling system was flushed at 90K. All done by the dealer along with some other items. Installed a bypass coolant filter at least 60k miles ago.
I have been having a no heat issue sometimes at idle this past winter and a mystery loss of coolant. I replaced the cap with a OEM one. I did a vacuum test on the coolant it held at 25 inches for well over a 1/2 hour. Pulled the egr valve it looked somewhat like tar inside not 100% dry. At startup it sometimes blows some white smoke and other times it's black smoke. I've had the scan gauge on for the last week to check my deltas.
Running 65mph the deltas stayed around 10 degrees diff.
Running 70mph the deltas stayed around 14-16 degrees diff.
Yesterday just running around rural roads 55mph and under the deltas stayed around 10 degrees diff.
I have not found a lower pressure gauge to do a coolant pressure test.
It does look as though it has burped the cap. Because of the deltas I'm thinking a plugged oil cooler my be the problem.
I have a 99 7.3, I took off driving the other day and after about 10 minutes the truck just dies like I shut the key off but everything was still on. I tried to restart it and it would fire for just a sec then die. I set for about 15 minutes and tried again it fired up and ran about 5 mins then the same thing. I had a buddy hook it up to his scanner and it has a p0605 and another icp code.. We changed the icp then erased the codes.. Ran some rest through the scan took with the truck running and no codes so we took it for a drive made it about 20 minutes away and same thing but this time has the p0605 code again. Could the pcm be bad? I also noticed the electric pump is always on all the time it will cycle at least 30 seconds every time the key is turned??
View 14 RepliesI have a 2000 f250 7.3 with about 230,000 miles on it. So I filled my truck up to go out of town got on my way drove about 50 miles and the next stop I made the truck shut off and would not start again. I figured CPS went out again! nope changed it still not start. So check the fuel pump seemed fine was getting diesel. Checked oil, was a little low so i topped it off nothing. So i left the truck over night and came back on sunday still nothing. I finally got it started with a shot of quick start i know its not good but i had to get this Truck home. I drove and made it almost home took my foot off the pedal and it stalled again so i pulled it home. Had a guy go over and scan it and it says the oil pressure is at 30 psi when cranking so he says the hpop is probably bad.
View 2 Replies