Ford 7.3L Power Stroke (1999-2003) :: Noticeable Vibration Between 20 And 25 Mph Under Heavy Pulling
Dec 30, 2016
I've got a 2002 F350 DRW 7.3 truck I'm having a little concern over. It started this summer, when under very heavy pulling I was getting a very noticeable vibration between 20 and 25 mph. I did not think much of it, as it only happened under extreme conditions.
Now I'm getting the vibration all the time, and it's started another band which is 40 to 45 mph. It's much worse if you are very light on the throttle, if you're full throttle it's much harder to notice.
Truck has 154,000 miles.
View 12 Replies
Advertisement
Did my starter yesterday. Today now several times, truck ran rough and stalled. Turned over, tach not bumping, no codes. Would go after a couple tries. Stuffed a new CPS into it. Drive 30 miles, now has a noticable miss, no codes, no smoke and quit again, but started right up.
No codes. Does not feel like another truck and under valve cover gaskets.
1999 7.3 Super duty!
View 14 Replies
1999 7.3 misses when starting it cold (first start of the day even when outside temps were around 20 deg C ). It has a noticeable miss and lots of white smoke. After warming up it runs perfect. I changed the GPR and tested all glow plugs, 3 bad and one weak one all replaced. Now that it is cold out it still misses when first started, even if left plugged in.
It will start and run for approx 3 seconds perfectly smooth then it starts to miss and idle speed slows down. on one occasion I went to start it after sitting 10 plus hours plugged in and it started then missed and slowly died. Would not re start, It was firing and smoking but not enough to get going again. Went back the next day and it started and ran fine for a few weeks. Did the same thing to me yesterday, started and then petered out and died and this time it will not re start after 2 days of trying on a couple occasions. I changed out the CPS with no luck.
View 14 Replies
While pulling onto the highway and pulling pretty hard lost engine power all boost then engine truned off. Top of engine is covered in oil..... What happened?
View 11 Replies
99.5 7.3. 201,450 miles, Just developed a new noise. Was on interstate, in cruise, 65 mph, started while pulling a hill. Kicked it out of cruise and noise went away. I have found it will repeat just pulling a hill at highway speed.
Now for the noise....it almost sounds like lightly opening the secondaries on a gasser 4 barrel. I don't see anything unusual under the hood.
View 13 Replies
I have a 2001 F350 with a PCM labeled "PMT2".
The SES light is triggered every time I try and pull fault codes using Torque Pro. It has done this since I installed Torque Pro many months ago. Same thing happens in another local member's (2000) truck, although I don't know his PCM version.
I'm very comfortable with the Torque Pro settings that have been detailed in other Torque Pro threads. I have been careful to choose conservative settings, including trying debug mode. I have uninstalled and reinstalled Torque Pro to see if that solves the problem - which it does not.
Question: "PMT2" PCM been able to pull fault codes using Torque Pro without tripping the SES light?
I realize another variable may be my OBD2 Bluetooth device. As an aside, I have removed the AIH and would expect to see a fault code but Torque Pro reports no fault codes.
View 8 Replies
So I'm getting ready to pull my engine to redo my timing cover.. my engine has over 320000 miles on it and it runs strong, dyno'd 402 hp at the wheels recently.. I was considering dropping a reman in since im pulling the engine anyway... I heard you can test for blow by buy sitting your oil cap over the spout and seeing if the cap blows off.. well the engine tilts downward in the back so the cap just slides off but in the dark when i shine a flashlight you can see the fumes just billowing out... how do i know if this is too much... what else can i do EASILY to see if my engine has issues before i start taring it down?
View 10 Replies
My transfer case engages the front drive shaft spins but even when I manually lock my hubs neither of my tires will pull! I was thinking either the hubs are shot but I was told it could be the 4wd locking solenoid??
View 1 Replies
Here's the deal. 99 Powerstroke out new injectors and orings. Did orings twice to make sure i didn't damage it. New turbo, new utvc gasket, new ipr, new fuel pump, I new complete engine wire harness. I pulled the injectors and ran in another truck no problem. New injector cups compression was all in the 300-375 range. Any cold start smokes like hell. Goes away when driving after the first time of hitting boost. Spits and shudders for a few seconds until boosting. Every time I stop it starts smoking again at idle. No power loss not using oil. Can't get a grasp on this smoking issue. When cold start I kill millions of mosquitos in a one-mile radius.
View 3 Replies
2002 F350 7.3, MANUAL transmission ZF6.
Bought this truck used for hauling an excavator, and after fixing damn-near everything engine/turbo/and-cooling-system-related ---- it's finally seeing some use.
Just recently started hauling 12,000lb payloads. When I accelerate hard in Low gear, and then shift into 1st and accelerate hard again, I feel the whole truck shuddering. It's like a shimmy-shaking vibration all through the vehicle.
It doesn't happen in higher gears, only when the following conditions are met...
1) Starting from a dead stop
2) 12,000lb payload (heavy)
3) Accelerating hard (Low, First gear)
I would also like to add that I experienced this shuddering vibration very intensely when I put the transfer case in 4wd LOW (front manual hubs left unlocked) and towed 14,000lb up a steep hill in 1st, 2nd, and then 3rd transmission gears.
^^^ By leaving front hubs unlocked and transfer case in 4wd LOW, I was effectively lowering my final drive ratio even more for extra pulling power in 2wd hill-climbing. I don't do this often, only when absolutely necessary. ^^^
I must also add that I do have slightly taller rims/tires than OEM ford WITH the original ford gearing (3.73) so I'm more like 3.51 final drive ratio.
02 F350 7.3l ZF6
View 14 Replies
My late 99 has 161K, I am the 2nd owner and bought from the Original owner. It is stock with no tunes. Auto/4wd.
It has had an intermittent idle knock and recently has gotten much louder recently when used heavily with towing for summer camping in the 7K range up steep hills. The knocking goes away above 12-1500 rpm. There is no noise when the engine is cold. It seems heavily temp/load/heavy use dependent. If driven lightly, the knock is quieter but still present. The trans was recently rebuilt and new billet converter installed, made no difference so it's not that it would appear.
I rec'd blackstone last week and the results are excellent. Running the cyl contribution test while hot in drive at idle reveals cyl 8 is running 4.9 to 5.4 Perdels. #3 is 2.2 to 2.8. 1,6,7 are 0. 2 is .6 and 5 is .4.... I haven't checked bolt torque yet. My question: Is #8 "fixable" potentially with bolt torque? Is it considered too far gone and should just be replaced?
View 14 Replies
I have had a 2000 f250 crew cab for little over a year now. Two previous times, after heavy rains, the cabin light would blink on and i would get a buzzing sound under the dash. I would solve the annoying buzzing sound by opening and closing the door. After a few times, it would work, but my clock and radio could go on without the key in the on position. The next time i used it, no problems... so i put that worry in the back of my mind.
This morning it rained really heavy, sideways type of rain. I opened the door and noticed a small puddle on the vinyl floors right where my left foot goes. OH,oh i thought, but the truck turned over and ran like normal. I picked up a heavy load of hickory in the bed and hopped back in and noticed my speedometer jumping from 0- 30 when I was going about 35. The OD light was blinking, but the transmission shifted normally. I got up to about 1700 rpm and the speedo was barely jumping at 53-55. I make another stop to unload the wood and go back home and i get an intermittent buzzing sound on the way home and no speedo. OD light would start blinking before i hit 2nd gear. I also noticed the odometer not working (speedo related, right?)
I got home and took the fuse relay cover off and found that if I would remove the #1 relay "plug" (black square box 5 prongs) that dreaded buzzing sound would go away, checked it out , plugged it back in, buzzing back on. The clock light still stays on and radio will turn on without the key. I think that water obviously leaked in over something electrical and i have been searching this and other forms for a couple of hours. I am within a couple of weeks of saving up enough to buy the gauges, exhaust and possible DP Tuner and now this happens?
View 14 Replies
Ok, my clutch has been giving me trouble for a little bit and I'm almost positive that I have a bent release fork. It also slips under heavy acceleration in 6th gear. I am planning on doing a clutch, compete with flywheel and release fork and a new rear main seal. My problem is, here within the last couple of days the trans would pop out of 4th gear if I was just coasting. It has been getting noisy over the last few weeks also. I'm no manual tyranny expert, but this is making me think I'm gonna need to have it rebuilt.
View 14 Replies
I just got my new up pipes put on as well as a 38R and pulling a hill hard my truck will hit about 22 psi then drop off slowly I have an electronic boost fooler wich has been on the truck since new pretty much but I don't get a CEL at all is this what I should be getting and I was on the 80hp tune? I ordered new boots and plenum inserts they just haven't got here yet. I know I had a leak before on my old up pipes because they rattled every now and then and I could see exhaust coming out of them when it was cold out but I could hit about the same 22 boost with my old setup. So pretty much nothing changed boost wise except it gets up to boost faster now. I would say it's defueling but I was always told the CEL would come on if that was the case.
View 13 Replies
I have posted a pic of a smoke issue I am having while pulling.
I just pulled a 10,000 lb trailer up a few 7% grades at 8-10,000 ft and the best I could do was 40-45 mph at 6mpg. Every hill would set a P1211 and when the truck downshifted to 3rd the smoke would go away for the most part.
Truck is 100% stock and pulls the same as my F350 with 3.73 gears but smokes a lot more.
The smoke is kind of annoying and performance seems sluggish especially given the 4.88 gearing. Where to start?
Has new ipr, hpop, icp, fuel filter, air filter, fresh 5w40 mobil 1.
View 14 Replies
Resealed HPOP, reinstalled, started right up, ran for good half hr, shut it down, started it next day, ran for 15 min. Revved it up, n all that, good to go, took it for a spin around block, died as pulling into driveway. At crank Dashcmd shows 200 psi on HPOP. I'm double checking the gear bolt right now. When I installed the pump I seated the gear by hand n torqued bolt to spec, so idk...
View 3 Replies
My truck 00' 7.3 255k is smoking white. It's not thick its more of a white haze. Sometimes it does it sometimes it doesn't. It has a 6637 intake, exhaust, and wicked wheel. No tuner or such. Im thinking either the turbo is going out or maybe a leaky injector? Just checked the turbo wheel and it has a little side to side play. On start up itll puff white then go away but then under heavy acceleration on occasion there is a haze of white then goes to haze of black. It also feels like the truck is lacking some power. There is no oil in the coolant or coolant in the oil. Not consuming oil or coolant. And there is no excessive pressure coming out of the oil fill.
View 8 Replies
I'm on the road and I pulled over for a pit stop so I don't have time for a search right now, but I noticed under heavy acceleration a turbo whine so high pitched it almost sounds like metal on metal. Is this normal and I just noticed it, a leak somewhere, or maybe indication of something worse? The truck seems to be running ok otherwise. It's an '02 w/7.3 and 220k miles.
View 3 Replies
I'll get right into it, when I put the mud grips on my truck it always had a little vibration from 42-45 mph and it wasn't to bad. Recently from 30-65 I have a bad shuddering vibration that I get mainly in the steering wheel but I also feel it everywhere else and can see it on the mirrors. Well the front sway bar has a bushing that is broken. But also I notice recently at low speeds from my rear drivers side tire there is a noise that isn't right, maybe a bad bearing? I have a long list of stuff I gotta do on the truck and I just want to stop the Shake so I can get to everything else.
View 14 Replies
As I'm cruising once I hit about 50mph I start getting a vibration in the peddles and floor board. It's not real bad but noticeable for sure. When I hit 70mph it's worse and the truck even sounds like it's vibrating. As soon as I let off the peddle and coast everything is golden.. Smooth.. So it seems to be a problem only under power..
A little back story : About a year ago I was getting bad vibration and loosing power. I put it in the shop and the mechanic said the filter or screen in the gas tank was clogged so he cleaned it. I went to Korea for a year so the truck sat in government storage for a year. When I got it back in March I put in back in the shop to have the front passenger side hub replaced.
I don't know if any of that has to do with the vibration I'm getting now.
Truck
2003 F250 ext cab
7.3l
179k miles
View 6 Replies
So I'm attempting to track down a grinding/vibration I'm getting only in 4x4. Mechanic checked the axle and front drive shaft u-joints and he said they're all fine. It's not the wheel bearing they are both fine, one is brand new. What to check next or how?
View 10 Replies
