Ford 7.3L Power Stroke (1999-2003) :: No Power - Truck Will Crank For About 15 - 20 Seconds Before Turning Over
Oct 2, 2015
I have a e99 f350 7.3 all stock. I have no power. The truck will crank for about 15-20sec before it'll turn over. I just purchased the*AE*but am fairly new to understanding it all. In idle its a little rough and when I drive I can only stay in the neighborhood because of fear of getting rearended due to very slow acceleration. Whats weird is that when i have no power while i am driving ill keep the pedal down throw it in nuetral and my rpms and*icp*pressure jump up right away. Things I've replaced:
Icp*sensor
Fuel pump
Pcm
Tps
Cps
Ipr
Dropped tanked and cleaned screens
When cranking my*icp*pressure climbs slowly to right under 500. I dont know what else to do ive been working on this truck dor two months some days 13hs straight, I am feeling defeated. Codes p1249 1211 1209....
View 12 Replies
Advertisement
Alright, my 1999 7.3 keeps dying on me in the morning. About two weeks ago I noticed it started to have a weaker start up, even though it has two brand new batteries. Once it starts up, I get around the block and it dies there every time. Then I have to crank it for about 15 seconds for it to start again.
The crank gets faster and faster until it finally start, and the engine is very choppy, like its starving for fuel. After about ten seconds of that it return back to a smooth idle. I then take off, and about 50 yards later it does the same thing. After it does it the second time, the truck runs just fine for the rest of the day with no problems.
I have noticed that when if I turn the truck on and let it idle for 10 minutes first in the morning, it won't die on me. I replaced the camshaft position sensor thinking it was that, but it wasn't.
View 2 Replies
On the way to work, the truck seemed to have a miss at idle and the CE light came on. Long crank to start leaving work, and truck starts losing power and eventually died. No smoke while it was losing power. Towed it home and checked the fuel pump and lines for blockage and found nothing.
2003 7.3 F-250 430K miles
strong cranking but no start no smoke out exhaust
Oil changed recently
IPR changed
Both UVCH gaskets and pigtails have been repaired.
ICP sensor and harness changed, also disconnected no change in cranking.
fuel filter changed today (no oil in bowl)
3/4 tank of fuel
dash gauge for lpop goes up to normal range during cranking and oil light turns off.
WTS light comes on and turns off as normal
tach gauge moves up between 100-200 during cranking
fuel pump turns on and pressurizes system like normal and turns off.
Ordered AE for the truck, and it directed me to the passenger side bank high open. Fixed the harness on that side and still nothing.
Sent off the IDM and it passed with flying colors
So now i'm leaning towards the HPOP, but would hate to fork over the cash for it and still not get anywhere. I'm going to take the valve covers back off and check the discharge ports for the injectors tomorrow.
View 14 Replies
I have a 2000 F250, 300k. Starts beautifully when cold, takes 10 seconds of cranking when at Operating Temperature. Did the injectors and plugs in September, kept doing it and now that it's summer it's getting harder and harder to start. Just replaced the ipr, still doing it. Gonna do an overdue oil change tonight or tomorrow, I'm hopeing that will improve it. I can understand 3 or 4 sec of cranking, but not 10. Truck hads no drivability issues whatsoever. Will an ICP fix it? Change to a heavy-duty 20w-50? (Last oil change was delo 15w-40) The code reader that I have is really basic, and only shows me RPM and map.
View 14 Replies
Started truck 3 times in 30 min. no issues with truck before tonight nice well cared for truck. Went to get a pack of buns at store came out --NO CRANK--all lights are on dash, etc, new starter a month ago, relay changed out in fuse panel just to see if there was a change. Bought two new Motorcraft batteries installed , NO CHANGE, so is it natural safety, key switch, electrical ignition switch, solenoid on starter, is there a solenoid between key and starter?
View 12 Replies
I've developed a problem, usually when starting, that the truck will crank over, start and idle for a few seconds and then shut off. The few seconds it idles it doesn't get any throttle input. I'll crank it back over taking a little more than usual to get it started. When it does start it seems slightly sluggish but that quickly, like almost immediately goes away and the throttle is working again.
Oh, 2001, 7.3 stock w/200k
View 1 Replies
I had issues with my F250 cranking last winter when the temperature dropped, so I changed out the glow plugs in the spring. I hadn't been able to truly test them yet, since it hasn't been cold, but the other morning my truck wouldn't crank up. It was 40 degrees out the night before, and it had been almost 24 hours since I cranked the truck, but it seems to me like the truck shouldn't have an issue in that mild weather.
I'm not sure what I need to do next to try and fix this problem, it's been driving me crazy and risks stranding me if I park for a while in an area where I am unable to plug by block heater in. The truck cranks fine when I have had it plugged in for a while, so I'm fairly certain it's a heating issue. I haven't done any tests since last year, but I know that the GPR was working properly last winter, which is why I changed out the glow plugs.
View 4 Replies
Trucks been running perfect for 11,000 miles atleast. its last issue was a bad turbo but that was my fault. No issues whatsoever since. 10 miles down the road from work last night truck had a slight miss in between 55-60 for four or five seconds, I put the pedal down and brought it up to 75 or so just to see if it was my imagination and it felt fine so i wrote it off. It ran fine to the house we're working on i wanted to check on before I got home.
Parked it, it idled down to 650 before it came back up to 750 and it never does that and sounded different then it usually does. so i felt something was definitely up. i shut it off, was at the house about a half hour before i decided to head home, started and ran fine, three miles down the road the slight miss came back, it seemed to go away if i got on it pretty good and when i let off but just cruising with slight throttle it had the slight miss.
Got to my road where i had to slow down and turn and it idled down and died. I coasted over, unplugged the icp sensor and it cranked for 10 seconds or so and lazily came back to life. I got it home running decent and parked it. Scanned it with my old super chips tuner and it came up with a p0340 camshaft position code.
Matched my symptoms i felt so this morning i decided id go back to work and grab my spare out of my wrecked truck. truck started and idled perfect. made it to the end of my driveway before the miss came back and then it just died. took the car to work, grabbed my spare camshaft sensor and my maximus scanner, came home scanned it, no returning p0340 cam code but i swapped the camshaft sensor anyway and watched icp and ipr data, the ipr voltage is where it should be and rises while cranking while cranking.
ICP is climbing to almost 3,200 psi and it will begin to run when it peaks out. she'll fire for 45 seconds after 25 seconds of cranking or so and then it'll just die. if it sits for a few minutes it takes a few seconds of cranking before ICP will come off of 0. I've come to the conclusion that it is making high pressure oil it is just dumping it as fast as it can make it. I changed the ipr out because that can do it, it didn't change anything so I'm on to believing an injector is dumping it as fast as possible.
Is it possible for something to come undone inside the injector to make it dump high pressure oil or will a bad o ring cause this? i'm leaning towards a failing injector as when it does fire and run its definitely misfiring and i just put new o rings on them when i swapped them over from my wrecked truck but that was like 45,000 miles ago as well..
View 6 Replies
So I had a reman 7.3 and 4r100 dropped in my 03 excursion.. since then the engine fires up every single time.. ONLY when the truck sits for 2 days i have this issue where the truck fires right up, runs for 4 or 5 seconds then stalls out.. It starts back up on first try and idles rough 10 seconds then it runs great.. If it only sits 1 day i dont have the issue if it sits 1.5 days it will try to stall out and catches itself from stall out and doesn't stall about 3/4 of the time. The mechanic who is a reputable diesel mechanic cant figure it out.. they called swamps and they also were unsure.
View 9 Replies
I was going to an appointment today and was going about 35 MPH and the truck just kinda sounded like all 8 injectors went into spaz mode for about 1-2 seconds. Initially I looked at the oil pressure thinking the oil pump went out. The engine/idiot light came on during the event and went off. But did not stall out in traffic. I was right in Green Bay Ugg that would have sucked.
I was a few minutes early and plugged in my Superchips reader to see what light code was there and it was a 1211. I have two questions for everyone.
1) Should I disconnect the ICP and check for oil, if so replace?
2) What hypothetically happened?
I now have a slight miss like a injector or something is not happy in one hole.
View 9 Replies
On my way to work today it was raining so I turned my head lights on. All the dash warning lights came on and my truck had zero throttle response. I quickly turned my lights off. The truck went right back to normal. I turned my lights back on and nothing happened.
View 12 Replies
When the block is cold my truck will not start. If i keep the block heater plugged in it will crank but is still a long start. I have tried just about everything i can think of and it is way too much to list so i will give as much info as i can.
New- gpr, glow plugs, HPOP, batteries, starter, fuses, valve cover harness/ injector and glow plug wiring, vacuum lines. I have checked out just about everything remotely possible.
View 14 Replies
When I start my truck it takes 30 seconds or so for the truck to start moving... especially when in reverse. If I give it some gas it doesn't take quite as long. I am not a transmission guy. I assume it has something to do with building pressure but I don't know what would be the cause. The fluid is full and looks good.
View 8 Replies
I drove my 03 f-250 to work Monday everything was good no issues. At end of my shift truck will not start . turn key dash lights up glow plugs cycle turn to start nothing . Does not turn over. after some checking batteries are good. Starter will crank if i manually engage it but truck will not run even with jumping starter with ignition turned on . hooked scanner up says cannot communicate. Checked fuses etc fuse #31 has no power to it (trans range selector and starter relay)question is where to look next?
View 9 Replies
This applies to a 2001 F-350 with 73,000 miles on the engine. Engine oil level is good, batteries charged, HPOP reservoir is full and passes Cody test with flying colors. Fuel pump runs for 20 seconds at key on. Start takes about 6 seconds. If I shut the key off and restart immediately it starts in under 2 seconds but if I wait about 30 seconds it's a 6 second start. Here is an AE that I ran on it, it has me stumped. FWIW it seems to start quicker when AE is hooked up. ?? An odd whir type of noise comes out from somewhere under the hood when I first turn the key on and when I clear the codes with AE.
View 14 Replies
Iam looking at a 2000 7.3 Powerstroke that has some problems first it is hard to start cranks like it has a dead cyl. Second after starting it has no power not even enough to move. At first it would only run if held wide open but once it warmed up it would idle and rev and move but barely still had a miss. The weird thing is it did not smoke blue-black or white also no strong smell of diesel and no smell of oil at all. The truck has 230ish miles and there are no maintenance records.air filter was new.
View 7 Replies
New to the forums, not new to fords. 1999 F350 7.3L Diesel. This has been a work truck and has seen multiple devices in and out over the years. I removed the last crap for GPS tracking etc from the last owners. The truck has worked well for a long time since until...
I'm moving slowly to a different state and so the truck got parked for 2 months. went to start it and nothing. the dash comes on and all the lights come on but when you turn the key to start the power drops and nothing.
Testing so far:
replaced the fender Solenoid
tested the starter motor and solenoid -passed
replaced the ignition switch
tested continuity of the hot and ground wires to the fender and starter and everything passed
When I shorted across the fender solenoid the starter works and tries to start the truck (unsuccessfully so far)
So the wire that goes to the fender solenoid is not working and where to trace it to and what needs to be fixed. Is there a relay or fuse besides number 30 that is in the way? where does the magical wire go so i can check its continuity?
I am stuck 800 miles from where i need to be and I am stuck here. I don't have the cash to get a mechanic and my mechanic friends are stumped. I do have a Snapon modus tester, what to do with it.
FYI the batteries are new and fully charged.
View 14 Replies
2003 250 superduty 6.0 ... I had to do the icp sensor. I went in from the top and discovered that the oil cooler was failing also. Replaced the icp and the oil cooler. Got it all back together. It would crank but wouldn't fire up. it did try for a about a tenth of a second. that's as close to firing as it got. The shifter has been loose. i ran it through the gears and the back into park. now it won't even crank.
Took the starter in to have it tested. it tested fine. Went to put it back on the truck. With no real force tightening the electrical connection it just snapped off the solenoid. put a new solenoid on it. Still no crank. Checked all related fuses and relays. They all seem to be good.
When I turn the key to on I get the buzzing noise and everything. Been through a lot of the no start check list. I don't have the ability to quite test everything. But what i can check. i do have an obd2 scanner. I cleared the code for the icp. I don't have any other codes showing. I have tripled checked that. After the weekend I am going to have to give up and take it in I think.
View 14 Replies
2002 f250 7.3l diesel...
I got a new radiator and the tranny fluid was the worst the mechanic had ever seen. He serviced it and warned me that it might not be long for this world. I broke my flexplate and so I had to pull the tranny, and I decided to throw a new torque converter in because it was giving g me symptoms like a broken sprag( it wouldn't rev up or do a brake stand in gear, therefore slow takeoffs).
I was recommended to replace the tranny, I decided I could do the job again down the road if I needed to. About two thousand miles down the road I had a hard shift going from overdrive down to get up a hill and about 10 miles later the truck started slowing down....I couldn't give it enough pedal to keep it going and the engine sounded rough.
I pulled over and checked fluids and everything was fine, truck idled fine, bright red tranny fluid not burnt at all. Pulled on to the road again and it pulled fine until about 40 mph and it wouldn't go any faster. I got it towed home and ordered up a tranny from Ford figuring it must be toast, but I thought I'd throw it out to the forum to see if there is any other troubleshooting I can do before I install the new one in case it is some other problem or some electrical harness or something, or if that is a pretty standard reaction to a fried tranny.
Engine runs good at idle, shifts perfectly to drive and reverse, drives forward and back(I'm very hesitant to drive it out of the driveway in case I can't get it back in). Only happened two times before I decided to tow it. Temps looked fine on the gauges, fluid was a little overfilled in the tranny, but again, not hot or burnt.
View 6 Replies
Problem started 2 days ago, driving around and my truck would stumble and lose power. Give it gas, won't rev up but it cleared and ran fine for a mile or so then it comes back (off and on all the way home). Check engine light didn't come on the first few times, came on a couple times on the way home (maybe 4 mile trip) but goes off when the truck runs fine. Thinking it was maybe the fuel pump (got 140K on the stocker). Talked to a few friends, some thought it was algae build up in the tank that was clogging the filter on the pump, underhood filter changed a couple hundred miles ago. Looked fine with slight brown build up at bottom of bowl when I replaced it.
Ran it around yesterday with a friend of mine and his scan tool hooked up, acted up once, check engine came on for a few seconds and shutoff. No code and for some reason we couldn't get it to live data while driving. I dumped in an algae eater yesterday and left the truck overnight since I had to work. Got home this morning to run her around the block to circulate the eater. Truck started and idled fine, went to pull out and she won't rev up, pumped the gas and NOTHING! Check engine light is on now but don't have a scan tool handy to read it. I heard the truck will store the code?
What this problem might be? What's a good scan tool for our trucks that can live data as well? CPS is good and already did the UVCH mod.
View 14 Replies
My truck runs very rough and lacks power when cold, even during the Texas summer. Once it warms-up, everything is fine. It's almost like turning on a light switch. If it's plugged in for a couple/few hours, it's smooth as soon as it starts. I'm assuming it likes the oil once it reaches a specific temperature. What my problem is?
View 14 Replies
