I have a few codes I pulled with and AE Using CCT and I got codes PO263, P0269, PO275..
Also got P0603, P1316, P0470 on power train
Did a BUZZ TEST P0273 and also check uvc harness
I've replaced ICP,OIL and Filter,fuel filter,CPS still no luck.
Today I just installed a brand new IDM and after running the Injector Buzz Test test, I received codes: P1298 Injector Drive Module Failure, P1293 Injector High Side Open - Bank 1, and P1294 Injector High Side Open - Bank 2. How a new IDM could throw these codes?
When running the KOEO test I received codes P0605 Injector Control Module Read Only Memory (ROM) Error, P1298, P1293, & P1294.
My engine is still missing but the engine is running a heck of a lot better after replacing the IDM and injector 8 has a rotational velocity of about 3%
I am pretty sure my pedal is going.. Today and last month it would just die from a dead stop push the pedal and no go, but truck idling fine. I cleaned it off a few weeks ago but now its back. push pedal in and out a few times and all is fine for a few weeks. Truck runs fine other than that. Does not throw a code, just trans light comes on because no movement I think, then it goes off as soon as i start to move along. I have a adjustable pedal assembly 2c3z-9f836-de 508.45 at white bear lake ford.
View 1 RepliesFor probably years, I have had a bump, thump type noise when I start from a dead stop... say at a red light. I had it in my head, maybe there was that much slop in the drive train... as old truck is over 400,000 miles.
Yesterday, I rebuilt the driver's side axle, bearing,seals, new hub...the works.. I heard that noise again later... and my thoughts were, I did all that work and I'm going to find a lower/upper ball joint is bad, although I did look at them and thought they were fine during the rebuild.
Had my wife get in truck.... and swing wheel back & forth... so maybe I could see what was loose.. or making noise.
I was shocked... just something I never thought of looking at. The u-bolts holding the leaf springs were loose... the whole axle was shifting back and forth on the axle. I've never touched those bolts....
ive noticed my boost has been going down lately. At first I thought it was a boost leak so I replaced all the intercooler boots and both sides of the intercooler pipes. That diddnt change anything at all. I recently got new injectors (200/30%) and a hydra tune for them and it was quick the first few days i was running with that setup, my boost has been dropping and currently at WOT I can't even get to 10lbs of boost and it is noticeable driving, it's slower than it was stock. There was no play in the shaft of my turbo and the turbo in there is only 2 years old. Could the turbo be bad already? Or is there anything else I can check before buying a new one. I have an upgraded hpop and the 6637 intake.
View 13 RepliesDrove the truck to the store tonight about 5 minutes away and everything seemed fine. Went to leave the parking lot and noticed the check engine light was on. Pulled out my tablet, dongle and fired up Torque Pro. Retrieved error code P0170. Truck has a little over 12,700 miles and is complete stock. I ran a search and didn't come up with much info on this code other than what Just Stroken posted in another post.
[URL]....
Looking for more information about this code?
I've got a 2003 F350 dually and wanna add more power that won't break the bank. What are some cheap things to do.
View 8 RepliesI am still failing to appropriately diagnose the problem(s) with my '03 Ford E-350 7.3L Powerstroke. This van has only 69,000 miles on it. A week or two back (just a few days back in work time) it suddenly went from running perfectly smooth, clean and wonderful to this:
- Zero power. Putting the van in gear and flooring the engine causes lots more smoke not nearly any rev of the engine and just a crawl forward.
- Lots of smoke out the back exhaust, whitish. I cannot discern wether it smells like diesel or oil (because I'm ignorant here), but the smell is very strong.
- After warming up and idling ~ 15 min I check under the coolant cap and see no signs of bubbling or disruption (from opening the cap in the coolant tank).
- After warming up there are no warning lights visible on the dash, and I don't have a computer to read codes (if there are any to read).
- I replaced the turbo up-pipes which had a visible leak previously. This did not hurt the symptoms, though no more visual leaks under the dog house.
- I thought maybe I put gasoline instead of diesel in the truck, not so.
- To do the above test I had to use the fuel pump to get gas out the tank to test. I hijacked the fuel pump output and turned the car on a few times to get gas out to a tank. The pump seemed to work just fine.
This was all very sudden which is perplexing, and, in use, the van was previously an ambulette and in my few miles with it (maybe 200-300 only) use was extremely light for such an engine/van, just driving around doing errands. I am not sure if this is relevant (no one has suggested so, yet) but before all this happened I uninstalled the rear HVAC that came with the van when I bought it. The AC lines were sealed under the hood. The coolant line was returned at the doghouse (you can see this at the beginning of the video).
At the moment the van has no power to go anywhere. I have not yet checked the CPS or IPC sensors, and understand this might be the next route in standard troubleshooting?
2003 Ford E 350 7.3L Trouble - YouTube....
Just bought a 03 F-350 dually today. 6L 4x4.
Headlights don't work , everything else does? Dash lights , taillights , cab marker lights all work. Headlights and front park lights don't?
I also see the overhead console is dead and shows nothing? Plus the ignition turns without a key being in it?
Last November I forgot to plug my truck in and it got down to 0, my girlfriend tried unsuccessfully to jump start it. When I got home I jumped it and got it running. I took it down to a heated shop to troubleshoot the glow plug circuit. I discovered it was not getting 12v to the glow plug relay. Also I started it and tried to back it up in the shop, when put in reverse it killed the engine, not lugged it down it was like you shut the switch off.
Also I discovered if you turn the lights on it kills the engine immediately. It will not crank with the lights on either. So far I have replaced the computer,ignition switch,batteries, and cam positioning sensor. Now comes the weird part!! I decided to get it running and pull the bulbs out of the back up lights I pulled the drivers bulb first then the passengers side bulb. When I pulled the passengers side bulb it killed the engine.
It is not my daily driver so it still sits in my shop. I have a hunch it's a ground issue but I've checked and cleaned up all the grounds I can find and it still has the problem.
On cruise control, engine went dead immediately after passing gear kicked in. After 2 days on the side of the road got a pull to the house. Then after having a charger on it over night the electric seems to be messed up. Switched on, the dash lights light full strength for a fraction of a second before appearing as thought the battery is real low. Also the doorlocks act crazy. I think maybe I blew out the BB on the high oil pressure pump.
View 6 RepliesIs there one thing that when broken makes both the steering and brakes lose all power? Does the power steering and hydroboost share a pressure source?
My brake pedal is dead and I get no steering boost, but the master cylinder and PSP are full of fluid. Do I replace both, or replace one first to see if that fixes both? Or could it just be a hose leaking? Not sure how to diagnose this one.
About a year or so ago, cyl 5 glow plug failed. 6 months later number 1 failed. Now number 3. I seem to remember someone mentioning that the module can sometimes cause produce similar problems. Are there two circuits in the module, one for the left and one for the right, or just one circuit for both? 167K on it so it doesn't surprise me that they fail but just odd that they are all on the same side.
View 5 RepliesI have a 2001 ford 7.3l powerstroke diesel. When I first noticed the problem I was towing a trailer going up a grade and got into the throttle almost to the floor and noticed a loss of power and the service engine soon light flashing extremely rapidly a few times and never came back on. I made it home, still lacking power but not running rough. I drove the truck to work the next day and the truck was running rougher and loosing power. It ran great through lower RPM's but seemed to trip as soon as you gave it over half throttle. eventually the truck wouldn't run right at all and lacked complete power. It idled rough as well. My mechanic threw the computer on it and it said injector pressure reading too high or too low.
I was told to replace the IPR on the HPOP and I did. (I also replaced the fuel filter and changed the oil). After replacing the IPR it ran great, had full power! then it began to slowly die like it did before until it sounded like it was running off 4 cylinders again. I pulled the ipr out, cleaned it and changed the oil again. It seemed to clear it up for an hour and ran great but then began ran rough again. I also replaced the CPS sensor. I feel like its not getting enough fuel or something, im just wondering if it could be the ICP or the lift pump. There is no check engine light at all. Its just got me stumped because cleaning the IPR clears everything up.... temporarily.
Ok so the saga is continuing, not sure if its because enigma hates this mod or if I shorted something out when I was cutting the wires and mistakenly touched the ends together (protected terminal ends) some how or the monitor piece is just old and the fact that it has been my previous truck and this truck for a total combined 8+ years causing this conundrum....anyways the gauge seems to work (yay?) but it looks to read only "8"DC V?? but I know the power port (in dash) works as expected....so I am a bit lost here....one of the digits does look to be faded out as if the device perhaps is going bad and needs replacement....
View 11 RepliesI just finished a cab swap and I'm having a little trouble. Here's a link to what I've done : [URL] ....
KOEO the WTS light, battery light, SES light all stay on and no power to fuel pump. No communication with PCM (using AE). All fuses are good, but no power to PCM fuse (#22). When I apply 12v to #22, the truck will start and idle - but poorly because I still don't think fuel pump comes on. The idiot lights all stay the same.
I did get to pull codes while it was running and got stuff like IAT circuit high (its not plugged in), fuel pump relay short to batttery, and a few other short to battery things (park assist stuff IIRC). I thought that might have something to do with the redneck idea to boost the fuse with an external power source?
Just thinking while typing, I don't have 3rd brake light hooked up yet (just thought of that, I'll hook it up first) and bed/bumper are not installed, so no tail lights or park assist stuff is hooked up. I'm also not using overhead computer, so it's not plugged in.
My next step is to go back through all of the connectors and make sure something isn't 1/2 way plugged in or possibly plugged into the wrong place(s).
Looking thru the wiring diagrams is not a strong subject for me, but I was trying to figure out how power gets to the fuse and how PCM relay works (does it complete circuit to ground to energize the coil?).
2003 F-350 - 7.3. With the key in the on position there is zero voltage to the fuel pump. Fuel pump fuse is good. I traced the red with black tracer wire from the pump up through the firewall and to the safety inertia switch. The switch has continuity so it's OK. Then from the safety switch I traced the green with yellow tracer wire to a fuse block plug connector. Then I checked continuity from that connector out to the #40 fuel pump fuse and it's open.
So I then i checked from the fuel pump fuse to all the back connections on the back of the fuse block and there was no continuity to any of them. So I removed the back cover off the fuse block to expose any issues. I found two board mounted relays. Now, from the fuse I get continuity to one of the relay connections. So did Ford hide the fuel pump relay and make it non replaceable? Also if this is the pump relay then what circuit energizes it? I need to make sure before I replace the fuse block.
i got a 99 F250 powerstroke with 148K on its clock, i have a couple issues that i cant find a definitive answer for, 1 just started recently, Its an automatic and when it shifts into third around 40 mph the rpms drop to 1200-1300 or so, its done it since i got it, but recently it wont accelerate like it should or used to do, i have to put it down and make it downshift to recover.
Now I have no CEL. and it is still running perfect just has very little power, I do have a 4 inch turbo back exhaust and have a TS 6 position chip with i usually run in +50hp mode, but it does this in all positions. Now issue 2 is when its 30 degrees sometimes it will not start. It'll turn over with now fire. but if i cycle the key again it'll fire right up like a champ? It has a 4 month old starter and batteries and a month old alternator and i have tried several CPS' and Contently check the connections.
So I have a 2002 7.3 Excursion and I think it is low on power. ICP is falling on its face when on a 60 or 80 HP tune. I have some boost leaks at the plenums and will work on that but that shouldn't cause my ICP to tank at full throttle. Following are some numbers I pulled with WOT runs up a 6% grade.
16PSI BOOST
EXHAUST PRESSURE 40
ICP 1900
80%IPRDC
this is with the 60 or 80HP tune on my DP-tuner. If I ease into the throttle I get
2700 ICP with
45%IPRDC
but if I stomp on the throttle it stumbles and ICP tanks.
Running the stock tune I can maintain
2700ICP at
40-45%IPRDC
Is this my HPOP being weak, or worn out injectors, to much of a tune or a combo of all three?
On the back of my truck I have two plugs to operate trailer lights/brakes etc but I only use one. The one I'm not using (pictured) I'd like to adapt for aux power in the trailer to operate some IP cameras. I need to know about the pin outs of this connector and what gauge wire to use between the trailer and truck. I plan on running the 12V and ground conductors from this plug through an adapter into the trailer.
In the trailer I'll have a 1000W inverter --> UPS --> TL-WR810N Router --> TL-SG1008P POE switch --> and 4 small ip cams.
My issue I'm having - 2002 F350 7.3L has an 8 inch bds lift with 37/13.50 tires. I realize these tires are big but... while driving 100kms/hr or 60 miles per hour and I hit the gas the truck barely wants to move (without pulling a load). Thought maybe a turbo but I have no mechanical skills so here I am!
2nd issue, there's a bullydog chip in that truck when I bought it. he said he always ran it on extreme. I found it puffs way to much black when on extreme and on performance it seems a lot better so that's where I have it?.
3rd issue, the transmission gauge on the dash goes into red when climbing up hills ( I live in the rocky mountains so a lot!) but the bullydog chip says the tranny is only at its hottest 140C? I don't believe that's to hot but I do believe my truck is derating a little while the tranny gauge on the dash is in the red? is there any quick fixes out there for these issues.