Ford 7.3L Power Stroke (1999-2003) :: No Brakes / Steering Making U-Turn
Sep 25, 2016
Was making a U-turn, and out of no where, had no brakes and no steering.. Not a fun situation to be in....
View 14 RepliesWas making a U-turn, and out of no where, had no brakes and no steering.. Not a fun situation to be in....
View 14 RepliesI have a 1999 ford f250 lariat 4x4 with 236,000 miles. Recently I have noticed when I am applying the brakes it sounds relatively normal until about 30 mph then it sounds almost like I have a flat tire or I'm running over a rumble strip, It's almost like a popping sound but a deeper sound.. I'm not sure how to describe it. The truck also vibrates violently when I reach speeds above 65-70 mph. Until about a week ago I could go 100 mph with no vibration whatsoever.
View 6 RepliesI've got an 01 7.3 lariat 4x4 with an 03 7.3 engine in it (long story behind that) but basically I noticed one day I had a hissing underneath my dash and my brake pedal was a little spongy but my truck stopped, well before I could get it to a shop and checked out it went bad. Coming up to a stop sign and as normal hit my brakes and right before it came to a complete stop the pedal shot to the floor and I lost power steering as well as brakes and went rolling out in the road and almost got hit. So it's been parked ever since and I have changed the hydroboost, the power steering pump twice, flushed everything and bled everything and still nothing, can't even find any leaks. What to even replace now or whether to just take it to a shop and spend another small fortune.
View 7 RepliesOk, so I leave the fire station this morning headed home and my steering felt weird. About 1/2 mile from home I hit a bump and my drivers side front wheel started making a screeching noise. I stopped and looked out the window and it appeared fine. I limped home and as I pull in the driveway, I lost all my steering. I look under the truck and this is what I found.
Not sure what to do. This is my daily driver and neither of my 2 mechanic friends will answer their phones.
Driving home from movies tonight, I lost power steering and power brakes and the pump started growling. Looked in the reservoir and it was all foamed up. Within the last 20k mi I have flushed the system and refilled with power steering fluid. No apparent leaks at this time. And happened like someone flipped a switch. Fine one turn, nothing the next. What are the chances this is a fluid issue and not a mechanical one? Start with flushing system and adding Mercon V? Or is it likely pump is damaged?
View 7 RepliesOn the final stages of prepping my truck for sale. I noticed today that occasionally while making a right hand turn the signal light will not work when you put the lever in the locked position (no dashboard arrow to the right and no front/rear light). I can pull the stalk upward, but not lock it, and it always works correctly. I am thinking a bit of corrosion on a switch, but I thought I would check and see if others have run into this.
View 1 RepliesMy power steering is only working when i turn it to the left. When I turn it to the right i have to get a 1/4 of a turn in until the power steering takes over. So i get under my truck to discover what seems to be a piece of my tranny missing. How screwed am I ???
View 11 RepliesThe steering on my truck has become a little heavy after making a turn and bringing the steering wheel back to center. The steering feels heavy like I had a front tire half way down. There's a lot of drag then once on center it's gone. Could it be the beginning of the end for my ball joints?
View 10 RepliesDrove it last night around 9pm. Parked it and went to drive it again this morning around 7:30. No cold weather here or rain. Here is what I know: When I turn the key I hear a click (not a repeating click) but the engine doesn't turn over. Batteries have 12.5 volts. I put my trickle charger on them and had full charge after about 3 or 4 minutes. When I turn the key the headlights do not go dim. I put a screw driver across the solenoid on the passenger side fender and got a strong arc. When I do that, I can also hear another click that sounds like its coming from the engine. I tapped the starter a few times with a hammer, but it still wont turn over. I'm guessing bad starter.
View 14 RepliesTrying to track down an issue (annoyance) I'm having with my 02 7.3 4x4 excursion. When I get in the truck and turn the key (after waiting for glow plugs) the starter doesn't actually turn over for 1-3 seconds and sometimes up to 5. When the truck does turn over everything works perfect it's just an annoying delay.
View 13 RepliesRecently my 2000 F350 7.3 crew cab has been making a growling/vibration sound by the glove box at idle. Seems to disappear at speed/higher RPM.
Any thoughts on what might be loose at firewall passenger side area?
I think my pcm has gone bad. My wait to start light won't come on an when I turn my key on I can't hear my fuel pump cut on anymore. My vacuum pump is also making a loud noise.
View 10 RepliesI've got an E99 powerstroke. Recently it's been getting hard to steer, if not impossible. When I'm parked i can't turn the wheel and it gets better if i Rev the engine up, driving is usually ok and going around corners. It's just low speed, low rpm that it won't.
Also every once in a while when braking it feels like i lose all power brakes. The pedal goes to the floor and the brakes let go, then i can feel the pedal pump back up and i get a good feeling brake pedal again that actually stops well. All this happens within about a seconds time. But the steering is by far the worst.
I just did the power steering flush with atf and it didn't work. I'm thinking i need a new power steering pump, but want to ask here first to make sure. The truck has 290,000 on it, and it never has been replaced to my knowledge. I bought the truck with 147,000 however so it may have been done before that.
My husband is on the interstate on his way home from work. His brakes went out, completely!!! No e-brake either! he replaced master cylinder about a month ago, brakes worked ok for about a week and started messing up again. Now he has no brakes what-so-ever... is there anything he can do to get home safely? I believe he has hydroboost unit.. he mentioned before a tiny leak from ps pump... brake pedal goes all the way to floor... no stopping..
View 12 RepliesYesterday coming home from Morgan Hill I noticed my injectors making a odd sound on all the down hills while coasting - IPR % would drop between 9.8-9% making it almost sound as if the motor was about to complete shut down, RPM range was 500 -800 rpm, ICP 450-550 but the motor almost had a sputter to it... no codes, lights and it didn't run weak or have a lack of power but I've never noticed it before ...
ICP is only a couple years old
IPR is about 1.5 old
Both replaced with OEM parts .. Is this normal - or do I need to start digging somewhere?
Yesterday while driving, i lost all power steering and power brakes (you would automatically think Booster). I pulled over, popped the hood and fluid was spewing from behind the power steering pump somewhere. I limped the truck home about 20 miles. I checked brake fluid and it was full. checked power steering fluid and it appeared to be empty. Yet when i added fluid it took less than a half quart. I started the vehicle to pressurize the pump and find the leak. Yet the pump never pumped any fluid. (one would thing pump was out) I am baffled as to if the pump went out, why fluid loss? If the booster was out, why do i still have brakes just without power assist? Andif a hose is blown, why such small fluid loss? I dont want to just start replacing parts till it get the right one
View 1 RepliesLooking for some tried and true fix to make these parking brakes hold just a little? Winter coming and with a six speed would like some resemblence of a brake....short of a brick in the drive. I have adjusted.....no luck. New cables ( thinking maybe stretched)..no luck. Shoes are new. Did notice levers where cable attach look to be worbled out.....gonna try to tighten that are up a little to see if that works but.
View 7 RepliesWill it work? My ring and pinion is fubar and I found a 06 with 99K local. I know I would have to change the brakes to fit my 16" wheels...Anything else y'all can think of?
View 3 RepliesSo the other day I had someone change lanes and slam on the binders right in front of me which caused me to slam on mine. Luckily no one got hit. Now my brakes feel different. Sometimes the pedal feels nice a firm other times it pushes in 2-3" before starting to brake. The fluid level has not changed in the resevoir and the hydroboost appears to be working fine. The power steering is still operating as before. I have checked the calipers and none are leaking.
My suspect is the master cylinder but was wondering if the symptoms are common with the master cylinder failing? I'm thinking internal o-ring has failed due to the near accident event. I'm going to do power steering flush just because I never have. Is there anything that would display these symptoms that I could check before buying the master cylinder?
I was driving on a short business trip and I noticed what I thought at first was clutch smell, and then I realized I had a brake overheating. I pulled over and the front right rotor and hub were very hot. The caliber not so much. I let it cool while I was at the meeting. About 1 1/2 hours later I jacked the truck up to see if the bearings felt bad. Seemed fine so I drove home trying not to use the brakes and the heat did not return. I replace the caliber with one from Ford, but the only lines I could find were from CARQUEST and they are made by Raybestos. I am assuming that these lines are made in China.
I have been looking for some braided SS lines, but can't find any for a 2 wheel drive dually with 4 wheel ABS. Where I can order some better lines???
I hated my old 1994 F-350 that had those Metal/rubber pins, they would mess up and overheat also, I thought that my 2000 would not have this problem, I was wrong.
FYI, about a month ago I replaced the rear pads, and changed all the brake fluid with Valvoline synthetic DOT 3. I installed Akebono pads on the rear and just today Akebono on the problem front side. Will change out line and pads on driver side later this week. I hope I got if fixed.
I just bought my first truck and it is a 1999 (Made in late 1998) F250 7.3 Super Duty it is 2WD with rear ABS and has 290k miles on it.
It has what seems to be the common brake shudder while stopping. I know the only solution is to replace the rotors and I have been looking all over the forums and internet and just don't know what to go with.
I'll be using the truck to do light farm work, pickup lumber, get a bed load of dirt and maybe pull a normal car trailer every now and then.
I'm wanting to get something that will prove to be trouble free long term and be good enough for what I need with out over paying for something that I will never fully utilize. I have looked at
R1 Concepts
Frozen Rotor
EBC - which doesn't have 2wd front rotors