Ford 7.3L Power Stroke (1999-2003) :: No Throttle - Check Engine Light Came On When Pedal Is Depressed
Jan 25, 2017
I have a 2002 F250 4x4 Powerstroke with Automatic. I have been having off and on issues for months with the throttle going dead. This only happens when I start it, if it works when started it will continue working until a different start session.
I have replaced the pedal several times before learning how to check its output with a meter and am quite sure that is not my issue at this time. However, when the pedal is depressed the check engine light lites up and nothing happens.
I am thinking it must be the computer itself, but was told there is another sensor or module under the hood that could cause the issue also which is several hundred dollars to replace as would be the computer.
Is there a way to test the computer, and what is this other module/sensor if it exists that could be the issue? Unhooking and rehooking the battery to reset the computer is no longer working to buy me a few more weeks, is there a simple way to reset the computer to try?
I love this truck when the throttle works but I am getting tired of paying on a truck while having to borrow a vehicle to drive to work.
View 5 Replies
Advertisement
I have a 1999 f-250 super duty 7.3 .... Recently my truck has started making a humming noise when push the throttle and I can feel a slight vibration, the noise and vibration go away when I let off the throttle, I have changed all five u joints, both wheel bearings in the front, the steady bearing, changed tranny and both diff oils, put new brakes and calipers all around and pulled apart the hubs but I can't seem to find what's causing it. What it could be or what I could check? It has an 8 inch lift and is sitting on 37's and some performance upgrades, could any of that cause this ?
View 9 Replies
03 F250 7.3. I busted a brake line last week somehow, Got it replaced and fixed up, Bled that line and everything was somewhat good.
Now, when i hit the brakes hard, I have pressure. If I let off even a little, My pedal will start to sink till i apply more pressure. I am gonna fully bleed my brakes when I'm home to see if this could solve the problem.
View 7 Replies
I own a 2000 F250 7.3 Powerstroke 4x4. The only aftermarket engine modification I have is a Tymar intake. The problem I'm having started about 6 months ago in a very erratic fashion. I would pull up to a traffic signal and as the light changed to green, without warning the truck would have no throttle response. The engine was running fine; there was just no response as I stepped on the accelerator pedal. Usually when I put the transmission in neutral, revved the engine a few times, the throttle would come back on line. This happened 4 or 5 times over the summer and then went away completely until today. Today it came back with a vengeance. At one point I had to shut the engine down completely to restore throttle response. It's a bit unnerving when it happens in the middle of a busy intersection. I was told that it may be the throttle position sensor. Does this sound correct and does it need to be replaced?
View 14 Replies
I put a 150 w converter into one of my 12-watt power female and all of a sudden when i turned the engine on my check engine light came on with 4 glow plugs bad and now won't pass smog. any way i can turn off the check engine light so it won't comes up on the smog test?
View 3 Replies
I bought my 2000 7.3L Ex as salvage back in 2005. It had been through a driver side rollover and the seller had restored it. We lived in North Idaho then. But I remember I always had an issue with the check engine light being on. I don't remember what the codes said, but many mechanics read them and determined that nothing was wrong. Many surmised that someone had put a high performance chip in the computer and that was what was causing the check engine light to come on. All of them reset the computer and every time it would come back on. Should I replace the computer?
View 14 Replies
1999 f250 7.3 101k California truck ... Scanned it said #1 glow plug did not clear the code. But now the check engine light is off again...
Questions : Harness issue ? Glow plug bad at 100k ? Glow plug controller ?
Start at glow plug work way back to GP CM or in reverse ?
Replacement Do all 8 or just the bank of 4 ?
Thoughts on replacement brands
Accurate diesel glow plug replacement kits any good, will they last ?
Or go factory glow plugs
What about Felpro gaskets
I heard about another brand of GP CM
View 14 Replies
2001 F350 290,000 no mods other than 6637, 2WD
Towed our new to us RV home last, only 15 miles from the dealer and yes its a big 5th for my truck at 12,000lbs. Anyhow, about 2 mins from home as I'm pulling off the freeway I got a SES light come up, then it disappeared. I checked codes this morning using forscan and nothing shows to indicate what it may be.
I was wondering if the transmission is getting hot if it throws an SES? It was only a short trip, but I have no real idea of the condition of the trans as the truck is new to us too - fluid looks and smells good.
Only new code is an ABS one c1229, c1233, C1234. I had 2 of them before - think the 1229 is the new one.
View 14 Replies
So when I bought the car, it had a check engine light. I had it checked it said cylinder 5 misfire. I assumed it was the glow plug so I bought it and replaced the glow plugs myself. Check engine light went away for about a day then came back on. Got it checked again and still said cylinder 5 misfire. This is my first diesel and I'm clueless as to what's wrong. Any way to check what's wrong myself?
Also just to double check, the cylinder number is 1, 3, 5, 7 for the passenger side front to back right? And 2, 4, 6, 8 for drivers side? And front to back means when looking at the front of the car? 2001 7.3 Excursion Limited with 232k miles...
View 6 Replies
Now that I have been driving for a while I kept seeing this light come on/off and I did a video below - I don't generally flash my lights so don't think I am aggressive - but I wanted to make sure to capture the video and the light coming on.
I was thinking valve cover connection the 50 cent mod - and maybe it's all coincidental - but I did have to pressure wash the troph where the oil collects and maybe something else got knocked loose.
[URL] .....
View 13 Replies
I have a 2000 f350 7.3 got a check engine light that turns off when rpms go up and a slow start. My mechanic said that there were no codes being blown, what is going on?
View 11 Replies
I have a 1999 f250 7.3 I was driving down the road today and I lost throttle along with my check engine light coming on. I pulled over and turned my truck off and now it will not fire back up.
View 6 Replies
I have a 2001 F350 with the 7.3 standard trans. The previous owner put a toggle switch to control the EBPV as an engine brake, I've never used it. It blows white/blue smoke when cold but has for the last 4 years and doesn't seem any worse now.
Last fall I ran the truck the lowest on fuel that I ever have, the light was on for a long time and I thought I would run out. I made it to the gas station and filled it up then drove home. The next time I drove it I went about 25 miles and it started to buck while going up hill. This got worse and eventually the check engine light came on and it stalled.
It wouldn't start again so I had it towed home. I got it started a couple hours later but it would run really rough and only for a minute or so then stall. It will usually start again once or twice and stall, then it wont start again until it has sat for an hour or so.
I didn't have a code reader at the time so I started reading threads. Here's what I've done to date.
Changed the oil and filter, it was way over do. New fuel filter.
The oil level in the HPOP stays about an inch from the top, I've checked it a few times after its stalled.
Dropped the tank and cleaned the screens in the pick up, no change.
The ICP had oil on it so I replaced it and a new connector, no change.
Changed the CSP with a grey one, no change.
Changed the IPR valve with one from a buddy that was on an engine that was running. The truck ran rough for a min then settled down and ran smooth. I let it idle for 20-25 minutes with no problem so I thought the problem was solved. After sitting for a month or so I fired it up and its back to running rough then stalling.
I bought a Vgate ELM327 connector and downloaded FORScan on my laptop. (I'm still not sure what I'm doing). These are the stored codes P1281, P0475, P1316, P0478, P0470, P1211. I cleared all the codes. I did a buzz test cold and the Injectors all sounded the same.
I monitored the truck while running (rough) the IPR is staying around19.92%, ICP is 701.4psi. After 5 seconds the ICP starts to climb and so does the IPR, at 12 seconds the IPR is 37.11 and ICP is 1835.1 psi the it stalls. The fuel pw,ms is around 2.50-3.0 until before it stalls, then its 1.66. The only codes that come up are P0475, P0470, B1473.
View 14 Replies
So about 3-4 times per day, my truck will accelerate very quickly with the slightest touch of the gas pedal, then followed by the service engine soon light...I checked for any codes to see what I may need to fix, but no codes are found.
What this could be? I am also having issues to where I a few times per day I have to put my truck in neutral to get it to start instead of in park...could the two be related?
View 8 Replies
2002 F350 7.3 PSD. 192k miles.
From my understanding, a CEL is supposed to illuminate each time you turn the ignition ON as part of normal startup procedure.
I figured the previous owner must have pulled out the bulb to hide the fact that the truck had a few "issues" before selling it, so today I pulled out the gauge cluster and it looked as if the CEL bulb was a tiny LED soldered directly into the gauge cluster itself. There were a few serviceable/removable bulbs for things like turn signal indicators, high-beam etc... but the CEL did not have a serviceable/removable bulb.
I've been driving this truck and working through it's "issues" and fixing things as I go, but it keeps throwing codes without the CEL illuminating. What's going on here?
I thought the check-engine-light was supposed to illuminate each time the ignition was turned on, and that it would come on each and every time the vehicle registered a fault code in the ECU/PCM.
View 14 Replies
I have a '01 7.3 Excursion 2WD. 220,000 miles. It has a 4" exhaust, K&N filter and Edge Reprogrammer set on emission illegal. It gets the best fuel economy and moves out very well for 8000 lbs. Recently, I started to feel a surge while making light throttle acceleration. For example, round a corner at 35 and try to gently resume the 45 Speed limit. It begins to accelerate and then cuts out or surges, sometimes several times. If I lay into it, it responds fine. I have serviced the air filter, the fuel filter, use synthetic Amsoil. I did notice a slight improvement after the service. Less frequent cutting out or surging. I also was in an area where Bio diesel is readily available. I added almost a full tank of B10 Bio and it seemed to work. Changed the fuel filter just after.
It has been cold for NC. This morning it was +14 when I started the truck. It seemed to finally catch on maybe 2 cylinders with lots o' white/ blue smoke. It cleared out in a few minutes and seemed to be hitting on all 8, or at least 7. Once it warmed up, it's fine. But I had the codes p0672, p0674, p0676, p0678. My question is: Is there a common thread in the fact that it appears that I lost 4 glow plugs on the same bank?
One arm chair quarter back's response to the surging, is that the under valve cover injector wiring harness may be breaking down, especially since the truck has 220,000 and the valve covers have never been off. I have a fresh turbo with the good wheel sitting ready. I have just been too lazy to swap it out. Would a fresh set of injectors be a wise choice, when I swap over?
View 14 Replies
Background: '01 Excursion 7.3 4WD, 264,xxx miles, batteries less than three years old, new alternator [URL] .... , using an Edge Insight for digital readings.
Problem: I replaced the alternator about three weeks ago, first week all normal. Second week alt/battery idiot light comes on, then to add more frustration it is consistently inconsistent in its reading.
The volts (upon starting) jump around 11.6 - 12.1 when first starting. The light comes on while accelerating and goes off during no throttle while cold.
After warm-up the light will come on intermittently even though the reading is 13.0>, but never during off throttle.
It seems to do this more when cold but it does not completely stop when it's warm. Yes, I don't think that should be a factor but it is a reality .
I'm thinking it's a bad voltage regulator.
View 4 Replies
The brief information:
1. Stuck/non moving in traffic on the freeway for roughly 1 1/2. During that time the AC was running, but once I noticed my "battery light" on the dash turn on, I turned everything off.
2. Since then while on my way home from work the voltage meter only showed barely 12 volts at full throttle.
3. I charged my battteries, and started it up today to go into work. While going to work the voltage meter showed 14 at its high point, but shortly there after it dropped back down to 12. At which time the battery light came back on.
New battery or alternator?
View 1 Replies
I have a 2000 F350 7.3 213,000 miles. Manual tranny, 2wd. It is my daily driver.
No issues until 2 weeks ago I pulled out and began shift gears when the engine died and I completely lose pedal. The engine does not shut off it goes to idle and the lights and power are fine but I quickly lose acceleration. After a couple seconds and a few pumps on the pedal it comes back. The problem is intermittant. Until yesterday it was only in the morning but then happened on the way home from work. Thinking ti was water in the fuel I used an additive to cure the water.
I changed the fuel filter just after I bought it in April of this year. I know there is a Injector Pressure Sensor that could be the culprit. EGR?
View 14 Replies
This morning on my way to work I pulled up to a light and the check engine light came on. I went to go and had no throttle response at all. The truck just idled through the intersection. About 45 seconds later the light went out and truck ran fine all the way back to work. What to look for or what it could have been.
View 5 Replies
2002 camry. The car will not accelerate. The throttle body makes a clicking sound when pedal is depressed.
So.. I took it apart and cleaned the contacts in it. In the mean time located a spare throttle body from a 2003 from a local yard. The old throttle body has a part number 22030-28030 and the replacement has a part number 22030 0H010. The replacement throttle body wouldn't even move when the pedal was depressed.
I put the old one back on.. and now it doesn't click anymore but the car in Park only revs to 2000 rpm's. Its not sticking or having any mechanical issue.
I checked the parts site for Toyota and the replacement is the new number. Superseded. Does the throttle body after replacement need to be reprogrammed? Or whats the deal. I wish I was more Toyota literate when it comes to this.
View 1 Replies
