I've searched, and gone back through my computer history and can't find it. I have seen a thread here which Mark contributed too which said what the max temps were and for how long etc. I know book is 230 and optimum is around 165 but there was some degree of play in that.
View 8 RepliesI notice my trans temp gets really hot fast. For instance just moving my trailer from front of my house to side yard makes temp go to 250. Without any load and driving a couple miles it does the same thing. It's been doing it since I installed the trans temp gauge just trying to figure out what's up.
View 14 RepliesCoolant temps getting much higher than oil temps under load. Is there any problem that could cause this other than a bad temperature sensor? Reading temps with an Edge CTS 2 monitor. Think I'm going to hook up a mechanical gauge in the morning and see what it shows.
View 8 RepliesHave to get rpm's over 2k before trans will engage, then in between shifts I either have to let off throttle or let engine rev over 2k to get trans to shift...
View 3 RepliesI'm getting a sound every now and then of what sounds like i'm running over rumble strips on the side of the highway. I'm guessing it's the trans grinding. Any thoughts?
View 8 RepliesI bought this truck with 200000 miles and its been flawless, its now 900 short of 600000.. I use it to haul everyday.. nothing heavy mostly a car or truck and every once in a while a skid steer. I got 560000 out of my trans, i take it easy. lol
at 350k I installed a Jw valve body drilled pump, tripple disc converter and solenoid pack.. at 560k it went, i pulled it and brought to a guy i trust as much as you guys trust BDS.. Ive had what Ive called a vibration since day one, could be a shudder, could be a shimmy.. what ever.. I brought it back and he says nothing would do that from a trans, so I went through drive shaft, new t case ripped apart rear end and its still there and I have just been dealing with it.. about 2 months ago it started acting up in first. when I pull down to drive I get the normal bump and start to go, it feel like the truck slows, then another bump and it climbs normally with the shudder.
took it back and he said maybe a stuck valve in small VB, so I pulled it and went down there and it was fine, I reinstalled and still does same thing. I then put a pressure gauge on it and it swings as it should sits around 70 psi and will climb, only in first it will climb and fall back to 70 like a switch was flipped, and the rest of the gears bleed off slowly or normally.. He then said it could be the big valve body, so I swapped that one out with another and no real change, maybe its a bit more noticeable.
I am at a loss. Could this be loose feed bolts? Could the shudder that I can feel at most speeds be the 1 gear slipping a tiny bit all the time? I am told that first gear is always on.. this truck has been a dream until this trans issue..
Above 0 Cel.(32F.) 145 F-165 F. even in summer towing. Winter when it gets -20 my trans temp gets warmer (not towing 165.F or higher) When it gets to -30 my trans temp gets to 175 F. or higher I have never looked at trans temps before on any vehicle that I have owned. I like that these trans get warmer when it is cold out and colder when it is hot out.
View 5 RepliesTrans temp used to be about 185 max, now it's running side by side with coolant temps (200-203 with Mishy 200 thermostat) after I did the 08 pan and filter upgrades. I added 9.5qts after the change of Valv Max Life and checked and double checked the dip stick bout half way up hot. This is normal operating conditions, not towing anything. Checked with TorquePro App. Why it would run so high? Did I do something wrong?
View 14 RepliesSo my transmission drove perfectly fine I just wanted to put an upgraded torque converter in especially after driving a customers' truck with a low stall converter. I know their not like for racing or anything but it's a work Truck with some mods to the motor nothing crazy. So I went ahead and bought a low stall triple disk converter and I drove around the block fine and went to go on the freeway and got into fourth but lost it as I hit 75 (was not flooring by any means and had it in the stock tune) now it will not go past second gear. Once it did this the o/d off light started to flash and I decided to do a stall test.went to 1800 in a Second. Suppose to stall around 1200-1300.
2000 f250 7.3 powerstroke dp chip stage 1 camshaft and 180/100 injectors coming at some point but stock for now
Well stock trans went two weeks ago so warranty company had another stock one put it (4r100). Finally got the truck today and I noticed my overdrive was flashing. I have no issues though shifts fine speedo works Rpms are normal I checked fuse 19 under the dash that's fine so I'm lost
If I turn the key on I can use the button like normal but once I drive it just flashes. It works but flashes .
So just got a new pcm installed since i fried the last one anyway. I had a new trans installed almost two weeks ago factory 4r100 now i have a p0720 code. Id take it back to that dealer.
View 8 Replies1999 7.3/4r100 4wd with the rattling torque converter.
I bought this truck 10-11 years ago to use as a tow rig for my landscaping company. It has been a great problem free truck, I have done brakes a few times, a water pump, ball joints but no issues with motor/drivetrain.
I don't know the history of the trans before I purchased. Ford didn't have history of it being replaced and even now it still has all the labeling on the case. I would have thought it would have been washed off in a rebuild. Again I don't know. When I bought the truck it shifted nice and crisp, having owned trucks before it made me think it had been rebuilt but this was my first and only 4r100. Other trucks are ZF6 manuals.
Anyway 10 years and 100,000 miles later it still shifts very crisp and fluid, has been changed a couple times, is nice and cherry red. I added a 6.0 cooler, temp gauge and filter. Never see the temp rise and haven't seen much in the filter.
About 25,000 miles ago the TC started to rattle, a known 99 problem. I figured surely the trans would go and I would do a rebuilt from Ford. It keeps going though so being a work truck I have kept running it.
A couple weeks ago the starter just spun and wouldn't engage. I pulled the inspection cover and noticed some missing teeth on flex plate. Got it to start my turning crank bolt a bit to good teeth and the starter caught. Now we are carrying a breaker bar and socket. It has happened a few more times so I need to replace flex plate.
Question is, since I need to pull trans to replace flexplate, should I replace TC (I would like to get rid of the noise)? Some people have said I will be replacing trans in a couple months if I mess with it. They say just spend $3000 on a rebuilt now with a converter. Not trying to be cheap but hate to just dump this trans that is still working great and has served me well.
I have replaced many transmission and done clutches in many trucks so I am familiar with the steps of removal and installation, just stuck on what I should do.
2001 7.3 auto, 2wdr, 291,000, Transmission sometimes shifts hard from 1st-2nd, 2nd-3rd. Problem started after I found trans dip stick tube broken and loss of fluid. Anything I can do without going to a shop. I've replaced the Broken Tube.
View 2 RepliesIv heard a few things about changing the valve body. I tow a trailer so was wondering on pros and cons of changing this. And also what brands are recommended.
View 5 RepliesPaid a shop 9000 to rebuild engine. Went to pick it had a major oil leak from back of the motor. They pulled the Trans and resealed the back plate. I test drove the truck and had some boost leaks and the AC needed charged. They pulled the truck in this morning and fixed those items. Now the truck will not move in any gear.
View 7 RepliesSo changing the oil in my truck the other day, I noticed the exhaust clamp at the union between my down pipe and first section of my exhaust has been rubbing the trans cooler line and there's a Nick in the granny pan. Lookin at the rubber grommet on the hanger, its stretched tight and looks like the exhaust has shifted over. What could have done this or possible fixes?right by now it's got a gob of high temp silicone acting as a stand off. Don't wanna put the new line in until I have the situation remedied.
View 10 RepliesI have a 1999 F250 4-wheel drive with a 6-speed tranny. The tranny is several old but has only around 100k on a rebuild. Three times recently it has stuck in 6th gear (overdrive) and I had to get really rough with the stick to get to come out. Afterwards the stick felt "thick" for a while and eventually everything seems to go back to normal. Not for sure but it may have started after pulling a heavy load, around 16k, which is not unusual for the truck. Other than the times it stuck and shortly after, the tranny seems perfect.
View 5 RepliesSo I put in new clutch yesterday. Reverse works, granny works, 3,4,5 work. ZF6 manual. But when I try to go 1st or 2nd. Its as if the truck is in neutral....what should I be looking for. I bought the truck having only knowing the clutch was completely shot, was not told about this 1&2 gear issue....
Do I need to pull the trans out again... or is there something I can see or adjust, because from what i can see where the shifter connects there is no adjustments. Is it probably a gear selector fork...or connection that took a crap. when moving in granny gear i did not hear any irregular noises....
Ok, my clutch has been giving me trouble for a little bit and I'm almost positive that I have a bent release fork. It also slips under heavy acceleration in 6th gear. I am planning on doing a clutch, compete with flywheel and release fork and a new rear main seal. My problem is, here within the last couple of days the trans would pop out of 4th gear if I was just coasting. It has been getting noisy over the last few weeks also. I'm no manual tyranny expert, but this is making me think I'm gonna need to have it rebuilt.
View 14 RepliesMy friend has just brought a truck and has lost 3-4 gear in the auto trans. We have the PO782 code coming up. Is there something in particular we should look at first.
View 2 RepliesDriving my 2003 today seen the "check gages" light on and the trans temp gage pegged on hot. CRAP, tranny time! look at the edge evo and it reads trans temp as -60F ???. Plugged in the torque pro and it reads 8,240F. At that point I figure its PROBABLY not that hot. Let it sit for a while and back to normal. Watch trans temp on torque pro as I drive it and everything is fine till it gets to about 150, then it jumps to 60F, then 30F, the 8240F. The cooler lines and trans pan are both feel normal. Picked up a new temp sender on my way home.
View 5 Replies