Ford 7.3L Power Stroke (1999-2003) :: Lose Accelerator Function After Hitting A Bump - CEL On
Jul 9, 2014
What would cause me to lose accelerator pedal function after hitting a bump? The engine remains on, the CEL comes on and after a few seconds or shifting into neutral and back into drive I regain the accelerator again and the CEL goes out
The truck shows no codes. It is if some connection makes/breaks intermittently when I hit a rough pavement. Also, she sometimes won't shift in reverse. Could it be related?
View 14 Replies
Advertisement
About 4-5 weeks ago my 2002 F-250 7.3 just died with no warning after coming off the highway and since then it hesitates/dies when hitting a bump or while applying pedal with the A/C on. The code that keeps popping up is the P0344 "CPS" and the code for back pressure sensor... I have replaced the CPS twice "making sure the 1st one was not bad", the back pressure sensor and the tube the goes the manifold, and fuel filter and still having problems... I didn't know if there could be a fuel pump issue or something else?
View 14 Replies
Problem started 2 days ago, driving around and my truck would stumble and lose power. Give it gas, won't rev up but it cleared and ran fine for a mile or so then it comes back (off and on all the way home). Check engine light didn't come on the first few times, came on a couple times on the way home (maybe 4 mile trip) but goes off when the truck runs fine. Thinking it was maybe the fuel pump (got 140K on the stocker). Talked to a few friends, some thought it was algae build up in the tank that was clogging the filter on the pump, underhood filter changed a couple hundred miles ago. Looked fine with slight brown build up at bottom of bowl when I replaced it.
Ran it around yesterday with a friend of mine and his scan tool hooked up, acted up once, check engine came on for a few seconds and shutoff. No code and for some reason we couldn't get it to live data while driving. I dumped in an algae eater yesterday and left the truck overnight since I had to work. Got home this morning to run her around the block to circulate the eater. Truck started and idled fine, went to pull out and she won't rev up, pumped the gas and NOTHING! Check engine light is on now but don't have a scan tool handy to read it. I heard the truck will store the code?
What this problem might be? What's a good scan tool for our trucks that can live data as well? CPS is good and already did the UVCH mod.
View 14 Replies
I've got an E99 powerstroke. Recently it's been getting hard to steer, if not impossible. When I'm parked i can't turn the wheel and it gets better if i Rev the engine up, driving is usually ok and going around corners. It's just low speed, low rpm that it won't.
Also every once in a while when braking it feels like i lose all power brakes. The pedal goes to the floor and the brakes let go, then i can feel the pedal pump back up and i get a good feeling brake pedal again that actually stops well. All this happens within about a seconds time. But the steering is by far the worst.
I just did the power steering flush with atf and it didn't work. I'm thinking i need a new power steering pump, but want to ask here first to make sure. The truck has 290,000 on it, and it never has been replaced to my knowledge. I bought the truck with 147,000 however so it may have been done before that.
View 3 Replies
I have a 99 F 250 7.3. It runs fine at idle even for a long time. When I drive around the block a couple of times it will start chugging and lose power and shut off. I have been mixing fryer oil with the diesel. I changed the fuel filter, oil change, crank sensor and fuel pump. I added 15 gallons of diesel and diesel treatment. Pulled fuel filter and bowel is full I'm not sure where to look next.
View 1 Replies
I have a 2001 F350, 7.3. My service engine light came on and immediately the truck started to run rough and lose some power. I've checked the under the cover connections and they were both connected, I replaced the cam position sensor and I still have the same problem. The worse part of the hold thing is that there are no codes stored so I'm flying bind. Where to go next.
View 8 Replies
I don't know if it's a new thing or if I've just noticed it but when I activate the OD off function the tranny drops into 3rd and the TC remains locked. This continues until/unless I slow down enough to drop into 2nd gear, then no TC lock when it upshifts to 3rd. There is a live tune in the PCM that came with the truck if that makes a difference. Is this a problem waiting to get worse?
View 5 Replies
The problem occurs when you hit bumps while braking, or if you get on the brakes to hard. It seems like the brakes lose pressure entirely and the pedal goes to the floor. It kicks back in when the ground smooths out, or if you are braking hard it slowly grabs again. At first i thought it was sliding, but it definitely is not. The truck appeared to be equipped with abs but the previous owner seems to have cut the abs wire/sensor at the hub. Another thought i had is maybe the brakes need to be bled and have fresh fluid put in them, I have not tried this yet (Plan to this weekend along with a dozen other things). Its rather scary when it happens. but i didnt think much of it until i nearly rear ended someone..with my younger brother in the car. Now i need to fix this asap.
View 14 Replies
OK, what does a glow plug control module do? The short bus I got has one on it. It looks like it fits right into the circuit without much, if any, modification. I got one with my short bus and am curious if it would be something worth adding to my pickup. So...what does it do and could I/should I install it?
View 4 Replies
Today I was driving about 35 mph when I drove over a small patch of rough pavement and I started feeling and hearing a rumbling sound from the right side of my truck.
It felt like I was driving on a dirt road so thinking it may be my flex plate I put the truck in neutral and the rpms went to idle and the rumbling stayed consistent with the tire rotation. When I get to about 5mph it just clears up and drives fine until I hit another bump.
Is this my wheel bearing?
View 8 Replies
I have a 2000 F250 superduty crew cab short box. It has any occasional issue of either just shutting down (engine dies) which seems to happen if i hit an occasional bump. The other issue has happened a couple of times which is it will lose power and just go to a rough idle. I shut it off and restart it and it will run fine. I'm wondering if it is the throttle position sensor.
View 2 Replies
When I turn on my fan for the AC or vent or heat, it works just fine on the first and second settings. When I move the fan speed to the third and last speed, I hear this sound that sounds like the blower fan is hitting something. I turn the speed back to the lower two settings and noise goes away. Sometimes I turn it back to the higher settings and the noise actually will go away but most of the time the noise is there.
I pulled the blower motor out yesterday and set it to where I can turn it on while out of the compartment and I didn't really notice a noise. I wonder if the noise is there but I am just not hearing it since it is not enclosed in the compartment? I also noticed there is a crack in the fan where it mounts to the shaft starting at the shaft and extending out one direction and also 180 degrees the other direction. Thoughts on if the motor is bad or just the fan? Or even something else that I may not be seeing?
View 4 Replies
If I could determine the resistance of the accelerator pedal at around 1000 rpms, couldn't I rig up that resistance and switch it on in the accelerator pedal circuit to make the truck go to high idle? Any flaws in my thinking?
View 14 Replies
I own a 2000 F250 7.3 Powerstroke 4x4. The only aftermarket engine modification I have is a Tymar intake. The problem I'm having started about 6 months ago in a very erratic fashion. I would pull up to a traffic signal and as the light changed to green, without warning the truck would have no throttle response. The engine was running fine; there was just no response as I stepped on the accelerator pedal. Usually when I put the transmission in neutral, revved the engine a few times, the throttle would come back on line. This happened 4 or 5 times over the summer and then went away completely until today. Today it came back with a vengeance. At one point I had to shut the engine down completely to restore throttle response. It's a bit unnerving when it happens in the middle of a busy intersection. I was told that it may be the throttle position sensor. Does this sound correct and does it need to be replaced?
View 14 Replies
I have a buddy with a 1999 F250 W/7.3 TD. His property is accessed through a couple miles of hard terrain, so this may wind up being a loose ground or something that pulled loose.Anyway, the truck just all the sudden won't accelerate. It'll crank & idle all day long, but when you hit the gas.....nothing happens. I realize the diesel doesn't have an accelerator cable, as it is drive by wire. First thought was the APP sensor(accelerator), but most of the dash indicator, O/D, etc. lights are inop too.
View 5 Replies
I have a 2000 F250 super cab and the doors rattle going over bumps. I've seen the weather stripping mod and intend to do this but my drivers side doors are touching at the top. Would this indicate that the busings are shot? With the doors open, when I lift on the outer edge there is no movement in the hinge area. The drives door and drivers side back door actually touch and rub at the top. Any pointers?
View 10 Replies
I have an issue with my 1999 Ford F350 7.3L diesel and stalling when the accelerator pedal is pressed and released.
Background: Initially the truck would not start, and from there here are all the things that I found wrong and replaced. (keep in mind that I troubleshot all the issues and every part that was replaced was proven faulty)... Starting with the glow plugs, all but 3 were faulty and not making a connection to ground. (only one broke off in the head, but I was able to get it out with out getting anything in the cyl)..
Valve cover gasket and harnesses, this is to include replacing the connectors on the engine harness cause both sides of the connectors were broken. The ICP was leaking into the connector and breaking the connection to the PCM, so the connector was cleaned and the sensor replaced. No issues from that now.
The IPR was replaced cause the oil pressure was erratic and not stable when I had my pressure gauge hooked up testing the pressure. After that was replaced the pressure was ok, and it climbed with RPM's and fell back down like it was suppose to. I could not get the PSI up to 3000 PSI even at full RPM's, but it did not drop past 600 psi.
The fuel tank was recently replaced, and all the fuel was removed and "fresh/good" fuel was put in. The fuel bowl was cleaned out and the filter replaced. (the fuel bowl did have a lot of crap in it like rust and dirt). Fuel pressure was at 95 PSI last time I checked, which is higher than the recommended 60 to 65 PSI.
That being said the engine did start and run, but was very rough and missing. So I did all the injector o-rings. Some o-rings were starting to split, and others were not sealing like the copper washer on the injector tip. I could tell by the amount of crap in the end of the injector. ( not the tip, but where the injector contacts the injector cup. There must have been water in there or something cause that part had all kinds of crap around it)
The engine smoothed out after a couple day of running it, but it would still stall when it was cold. The block heater was replaced cause it was falling out. The oil was changed and the filter too. The CMP sensor was changed just because I know they will cause the engine not to start. I had a "known good" truck that I can swap part to and from, and I did a lot of that thus far.
Swapped the IDM, PCM, EBP sensor, MAP sensor, all relays inside the engine and in the cab. I was looking for the barometric pressure sensor, but from what I have read thus far that is a calculation in the PCM between the MAP and the EBP sensors. The diode to the PCM is good,I checked the harness for rubbing by the 42 pin connector and by the LF fender but I did not find any chaffing or rubbing on any wires. The ECPR was wired together, so I fixed it so that it is no longer that way, and the waste gate for the turbo was wired open. I took the wire off and made sure the linkage worked and it did move. I tried to lube up the valve in the turbo for back pressure, but I'm not sure if it worked or not.
I also swapped out the oil pressure sensor and the oil pressure temp sensor on the HPOP Reservoir, and blew out the EBP sensors tube. (air went straight through the tube with no restrictions.) I did a buzz test and all the coils checked out ok. I also did a contribution test and only three cylinders were identified as having some kind of issue. (but this is not enough to cause the engine to stall..) The only current codes that I have are the air intake heater, and the EF feedback not detected. Neither of which would cause the engine to stall in my opinion.
Symptoms:
When cold: The engine will start and idle just fine, but when the accelerator is pressed and held to 1000 RPM's the engine will sputter like its missing and surge up and down between 500 and 1100 RPM's. If the accelerator pedal is pressed quickly the engine speed to increase then fall down and stall. It seems as if the PCM is shutting down and starting back up. ( Like the key is turned off and then back on quickly, but the engine doesn't recover)
When warming: This issue becomes more erratic, but when hot the engine is fine. No issues, and it will drive all day long with no hesitation.
The truck has over 200K on it, but I know it will go more! It is a mannuel tranny, and is a 4X4, and I love it, I can't get ride of it just yet.
View 14 Replies
2001 f250 7.3L, 289,000 miles, changed the IPR and ICP, noticed the EBP tube was in two pieces. Would this cause the rough idle and shaking? IT started running rough and would die after a mile or two. Would have to wait 30 minutes before it would start again. That is when a buddy told me to change the IPR and ICP the ICP plug was covered in oil as well as the top of the ICP. So I changed the wiring plug as well. I originally cleaned and changed O-rings on IPR but then it wouldn't start, bought a new IPR and started but runs rough. I just started it with EBP tube removed and sensor unplugged. Idling rough when I press accelerator and RPM go above 2K it levels off pouring black smoke everywhere.
View 3 Replies
For probably years, I have had a bump, thump type noise when I start from a dead stop... say at a red light. I had it in my head, maybe there was that much slop in the drive train... as old truck is over 400,000 miles.
Yesterday, I rebuilt the driver's side axle, bearing,seals, new hub...the works.. I heard that noise again later... and my thoughts were, I did all that work and I'm going to find a lower/upper ball joint is bad, although I did look at them and thought they were fine during the rebuild.
Had my wife get in truck.... and swing wheel back & forth... so maybe I could see what was loose.. or making noise.
I was shocked... just something I never thought of looking at. The u-bolts holding the leaf springs were loose... the whole axle was shifting back and forth on the axle. I've never touched those bolts....
View 3 Replies
I have a 2001 Ford Excursion Limited 7.3l with 199,980 miles on it.
It has a TS-6. My first problem is that when I come to a stop or slow down to a crawl then press the accelerator the engine stalls and dies. I have looked and looked at threads and can not find this example anywhere. There is no pressing the pedal and it remains at idle. It dies, shuts off, quiets. I have thought icp, tps, ivs
Second problem is that a/c is blowing hot. Other than being out of Freon, what could be other things to check. It does sometime go to default, but has done so in awhile. It does not blow cold in rear and hot in front. They both blow hot. I have replaced the pvh sensor.
View 1 Replies
I picked up a 2003 6.0 awhile back went ahead and did studs,gaskets, delete. Was driving it and seemed to lose power, started coughing and carrying on blowing bluish white smoke then shut off. Ended up hydrlocking #5, Oring on injector was tore when took out. Put all back together, ran horrible, did a balance test with AE, showed #3 injector, replaced, ran horrible, did AE dropped #1 injector. So in process of replacing the rest of the injectors. Just wondering why it is or was dropping them 1 at a time. Ficm was showing 47.6 to 48.6 volts, could that be it?????
View 14 Replies
