Ford 7.3L Power Stroke (1999-2003) :: Little Squeak Only Happens In Reverse
Oct 20, 2015
So this started yesterday when I pulled in to my drive way and it only happens in reverse. When I back up it sounds like a mouse is under the truck I think it is the rubber part of the seal on the front of the rear deferential. Can I just replace the seal and be good or is this something that could be a bigger problem? My deferential fluid level is full. I also have slop in the rear end if I go from drive to reverse you can here the thud/clunk is there any way to tighten that up or am I just looking at having to rebuild the whole thing.
View 8 Replies
Advertisement
What is failing. I have a 2000 F350 PSD with 116k miles. When I bought the truck last year, I noticed that the clutch pedal would squeak while it was coming off the floor. It doesn't happen when the engine is cold. I need to drive it about 30 min before it starts to happen. On longer trips, several hours, the squeaking is louder and the pedal gets very stiff. When I stop for fuel, I've come close to stalling when coming out of 1st gear. I can push the pedal to the floor, but on the way up, the pedal squeaks, and then once I reach a certain point, say 3-4 inches off the floor, the pedal looses all freeplay. The best way for me to describe it is the pedal travels up faster than it normally does when it's cold, and if I don't compensate with more throttle at that point, it will stall.
I've learned a lot by reading this forum for the past year, but I don't know the first thing about how to diagnose problems like this. I've taken it to 2 mechanics for test rides -- one thinks the clutch is fine and thinks the problem is the slave cylinder or a broken bushing in the pedal.
The other shop is also a small independent shop, but they specialize exclusively in Ford trucks, so I thought they would be more knowledgeable. But now I'm wondering if they could sense my ignorance and are taking advantage of the situation. They also took it for a drive, but they think the slave cylinder is fine and that the clutch needs to be replaced. I questioned him about the slave, and he pulled it to look at it, and asked me to push the pedal slowly while he was under the truck. I still had a little resistance and a faint squeak even in this situation. But he said the hydraulics are so simple that he felt we could rule that out. I can't remember exactly what he said, but I think he believes one of the springs in the clutch plate has failed. I just know they are suggesting a new clutch and they want to machine the flywheel to original specs.
I thought the leading symptom of a failing clutch was slippage under a load. So under strain, I would expect my engine to race occasionally, like I'm in neutral. But I've NEVER experienced anything remotely like this, even when driving hard in the hills pulling my travel trailer.
I know something is wrong, but based on my limited knowledge, I'm not sure what. It's getting a little harder for me to move the shifter into 1st and reverse, but once it's there it's fine. I've never experienced any racing or slippage in any gear. The one definite symptom I have is that squeaky pedal that when driven for a couple of hours, gets so stiff that it can cause near stall outs. With those symptoms, what do you think is going wrong?
View 2 Replies
Last November I forgot to plug my truck in and it got down to 0, my girlfriend tried unsuccessfully to jump start it. When I got home I jumped it and got it running. I took it down to a heated shop to troubleshoot the glow plug circuit. I discovered it was not getting 12v to the glow plug relay. Also I started it and tried to back it up in the shop, when put in reverse it killed the engine, not lugged it down it was like you shut the switch off.
Also I discovered if you turn the lights on it kills the engine immediately. It will not crank with the lights on either. So far I have replaced the computer,ignition switch,batteries, and cam positioning sensor. Now comes the weird part!! I decided to get it running and pull the bulbs out of the back up lights I pulled the drivers bulb first then the passengers side bulb. When I pulled the passengers side bulb it killed the engine.
It is not my daily driver so it still sits in my shop. I have a hunch it's a ground issue but I've checked and cleaned up all the grounds I can find and it still has the problem.
View 10 Replies
I have a 2002 f250 CC 4wd 7.3 and I have no power to my reverse light sockets. I am stumped, all my fuses are good, I don't think there's a relay so i haven't checked that. My neutral safety switch is good, I'm getting power to both the blue/pink and black/pink wire. What it could be, at first it was constantly blowing fuse 27 every time I put it in reverse but then it stopped blowing it obviously because they won't come on.
View 8 Replies
This just started happening last week. When I put the truck into reverse, the engine lugs down and dies. It' as if the AT is fully engaging reverse gear with no clutching action. If give the truck a bit of pedal, I can put her in reverse and back up without issue. Going forward into Drive has no issues.
View 8 Replies
Installed rebuilt transmission 1 month ago. Have noticed reverse has started to go away. Feels like it is slipping or tires are losing traction with a lot of vibration in the steering wheel.(tires are not slipping that's just the way it feels).. Does it worse when trans is up to temp. I suspect feed bolts but want opinions.(Mark K.) All forward gears seem fine with no issues. I have never been under the pan deep enough to access the feed bolts.
View 3 Replies
I'm wiring a backup camera and I need to energize a wire with +12v source that turns on when the truck is placed into reverse.
If I can connect the wire to 12v which automatically energizes when the truck is shifted into reverse, the backup camera will turn on automatically.
Surely I could pull the signal from the reverse lights, but I'd like to find something in the fuse panel because that is where the wire terminates and I'd rather not extend it all the way to the reverse lights on the back of the truck.
Where's a +12v source in the fuse box area under dash that energizes when the truck is put into reverse?
View 9 Replies
I'm getting ready to put in my new double din and it said to hook the wire for the camera up to the reverse light wire. Which one this is on the harness coming out of the column?
View 14 Replies
Just bought an 01 F250 7.3 but it will not move I think it has something to do with the fuses because it won't go in forward or reverse but I can't find an accurate diagram For fuse box I'm missing probably 8 fuses underneath the dash and I think one of them has to control the transmission module. What it could be if someone doesn't think the fuses...
View 9 Replies
my parents have a f350 which now has no reverse. it has a reman sticker on it, 230k on the truck but no idea on mileage on the tranny. shifts 1st through 4th fine, no slip. Tc lockup works just fine. No codes found with my solus scanner. When shifted in reverse it will move back about 2 ft if revved above 2k and then nothing. Am I looking a trans rebuild or is there something I can check and repair with in it the truck?
View 4 Replies
I have noticed that I have to hold my gear selector towards park to get the reverse lights to come on. Also some times I have to hold it towards park to get it to start. I changed my tranny in Dec 2009 and occasionally it would do this while starting, just noticed the reverse lights about a week ago. Tried moving the cable where it attaches to the tranny a couple of serrations each direction. No luck. Is there another place I can make an adjustment?
View 14 Replies
I have a 2001 f 350 7.3 diesel r 400 tranny 320000 miles. . Im having transmission issues. It makes a slight whine/ grinding noise only in first And reverse. And it surges. Sometimes its fine though to. Check engine light came on. Only codes i get are #4 glow plug out and a low boost pressure. Checked boost before fixin Running fine at the normal about 20 psi. ive read a bad or dirty map or iat sensor can cause transmission issues along with the low boost error code. But in my experience and some reading it sounds like a stall converter.
View 9 Replies
When I start my truck it takes 30 seconds or so for the truck to start moving... especially when in reverse. If I give it some gas it doesn't take quite as long. I am not a transmission guy. I assume it has something to do with building pressure but I don't know what would be the cause. The fluid is full and looks good.
View 8 Replies
I have a 2002 7.3 e350 quigley 4x4 Sportsmobile with 312k miles. 2nd owner. Bought it with 295k miles 2 years ago. From what I gathered the tranny is original.
After reversing at a downhill angle, stopping, and shifting the lever to Drive, the tranny doesn't seem to put Drive in gear and depending on the angle of the slope, the van will roll back or barely creeps forward even with throttle. Put it in 1st gear, and the tranny engages that in gear and drives forward no issues, then I can shift to 2nd, then Drive and the tranny shifts fine after that.
No weird tranny noises or clunking. Noticed this issue about a month ago or about a couple thousand miles ago. Did tranny service (drain, filter, fill) at the ford dealership at 305k months ago.
I can only replicate this issue when Reversing on a down slope. On a flat surface van Reverses and engages Drive like normal.
View 7 Replies
On my way home from work the other day my 2000 7.3l started making a humming sound while driving. I noticed that it was shifting harder and it began to slam into gear when I would take off from a stop. By the time I pulled into the driveway I had to be half way into the pedal to keep it moving. I shifted into reverse and it clunked loudly and didn't want to back up. I don't know much about transmissions but I'm thinking that it's probably shot. I'm hoping that it's something other than a complete rebuild but doubtful.
View 6 Replies
My new truck has developed a squeak in the front suspension every time you go over little dips and bumps in the road.Which is all the time.
View 3 Replies
Not persistent, but the squeak I had where peeps thought it was the brake warning is back, but not constant.
Seems to happen above 30, and not sure what the other conditions are (maybe hot brakes). but it sounds like only the front right this time.
I've new Rotors and pads. I am on the road right now, been since the 20th and wont be back till the 2nd or 3rd.
View 3 Replies
I have a weird rubbing/squeak noise from what it sounds like the rear. It occurs only after ive been driving for about an hour then it never goes away. Thought it was the pads so I put all new ones on. Maybe a bearing of some sort. I'm totally going nuts over this and cant pinpoint it!
View 14 Replies
I am still failing to appropriately diagnose the problem(s) with my '03 Ford E-350 7.3L Powerstroke. This van has only 69,000 miles on it. A week or two back (just a few days back in work time) it suddenly went from running perfectly smooth, clean and wonderful to this:
- Zero power. Putting the van in gear and flooring the engine causes lots more smoke not nearly any rev of the engine and just a crawl forward.
- Lots of smoke out the back exhaust, whitish. I cannot discern wether it smells like diesel or oil (because I'm ignorant here), but the smell is very strong.
- After warming up and idling ~ 15 min I check under the coolant cap and see no signs of bubbling or disruption (from opening the cap in the coolant tank).
- After warming up there are no warning lights visible on the dash, and I don't have a computer to read codes (if there are any to read).
- I replaced the turbo up-pipes which had a visible leak previously. This did not hurt the symptoms, though no more visual leaks under the dog house.
- I thought maybe I put gasoline instead of diesel in the truck, not so.
- To do the above test I had to use the fuel pump to get gas out the tank to test. I hijacked the fuel pump output and turned the car on a few times to get gas out to a tank. The pump seemed to work just fine.
This was all very sudden which is perplexing, and, in use, the van was previously an ambulette and in my few miles with it (maybe 200-300 only) use was extremely light for such an engine/van, just driving around doing errands. I am not sure if this is relevant (no one has suggested so, yet) but before all this happened I uninstalled the rear HVAC that came with the van when I bought it. The AC lines were sealed under the hood. The coolant line was returned at the doghouse (you can see this at the beginning of the video).
At the moment the van has no power to go anywhere. I have not yet checked the CPS or IPC sensors, and understand this might be the next route in standard troubleshooting?
2003 Ford E 350 7.3L Trouble - YouTube....
View 14 Replies
2011 Ford F350, 69K miles... Just started, at about 30mph. I am hearing a Chirp from the front, speeds up when I speed up and goes away with brakes or slow below 30.
Friend thinks its the brake warning telling me its time for new. Bugging me. Just started. Never changed brakes.
View 14 Replies
I have a 2002 7.3L Screw 4x4. Will a 03/04 6.0L instrument cluster work in this truck? The 2 clusters appear identical. I put the 6.0 cluster in and the trans temp, and coolant temp gauge will not work. All the gauges sweep when it is powered on, but the coolant and trans temp lay flat, and the check gauge light is on. All other gauges and functions work. When I put my other cluster in, all gauges work fine. Is there a difference in the VSM, PCM, or the SCP communication?
View 6 Replies
