I have a late 99 7.3 that developed a knocking noise. I pulled the passenger's head and cylinder 5&7 have a spot where it looks like it came in contact with the valve. I'm not some master mechanic but am learning. What would be my next step to find why it hit the valve and to fix the problem?
View 14 RepliesChasing this knock and I'm starting to get a little bit worried. So I'm looking for what I should do next.
Here is the truck info... 2000 F250 4x4 206k. . Swamps Diesel 200/30's. Terminator HPOP. GTP38R. EBPV delete pedestal. Banks wastegate. AFE stage 2 intake. RiffRaff FRX. 4" exhaust. Hydra chip. John Wood Auto. 6.0 Trans cooler.
I have a knock sound coming from the area of #8. It is noticeably louder in that area with a stethoscope. Its not any louder anywhere else (oil pan, block, otherside of engine, or front). Truck does not smoke and runs and idles great otherwise. Was thinking possibly the cackle/fuel knock issue these trucks have but with bigger injectors and the FRX could this even still be a possibility?! Anyways here is what I've done.
Checked fuel pressure and at idle it is 61/62 with any tune. At WOT on Econ tune it goes down to ~40ish psi. With the extreme tune WOT dived down to 28/29psi. So my thinking was maybe that injector got screwed up so...
Swapped #8 injector with #2 so the front injector with the back to see if either it had some bad o rings or isolate the injector as the problem if the noise moved cylinders with the injector. While I did this I put brand new O-Rings on those two injectors and popped them in. Got it fired up and the knock is still in #8.
Unplugging the injector with the engine running the noise seems to disappear. HOWEVER, when I use the stethoscope the knocking noise still sounds like it's there but very faint. Without the stethoscope I can't hear it. Also driving the truck down the freeway and letting it coast the noise goes away when the injectors get cut off.
Recently pulled off valve cover and checked the pushrods and rockers on #8 and all looked fine. At this point I'm thinking wrist pin, rod bearing or cracked piston??? Could it somehow still be a fuel knock?
I need a film crew to document this stuff, but here's what I've got. This engine had a cracked piston. It is currently torn down and ready to go to the machine shop. I ordered a powder coating set up, so everything that fits in the oven will get powder!
This engine will get cut/coated pistons, cryoed forged rods, 250/100's, waste gated T4/S369, head studs, 910 valve springs, smith bros pushrods, etc. We'll also be using a Southbend dual disc clutch in front of the freshly rebuilt ZF6.
Here's some of the shiny stuff.
I think I'll give up a little top end to spool faster. Especially since this is a 6spd build.
Noise goes away (or maybe it quietens to the point that you can't hear it) when you raise the idle just slightly. No smoking, no hard to start, no rough idle, no indicators of anything wrong at city or highway speed, nothing else out of the ordinary to report.
275K miles
[URL] .....
My 2000 7.3 2wd is making a knocking sound while accelerating. It speeds up as I accel and when I let off the gas it gets louder. It slows down all the way to a stop when the truck slows to a stop. I can feel it in the floor board a bit as well.
View 8 RepliesI have begun to notice a "Knock" or "rattle" in the engine. I know diesels have a tendency to sound like that just from running but that sound is more of a "cackle" if you ask me.
I can hear the "knock" most noticeably at hard acceleration or taking off in general. It can also be heard during idle and every so faintly at deceleration with the torque converter locked so it makes me thing its mechanical due to the nature of the way the sound is audible.
I believe the sound is coming from the passenger side bank as that is where I can hear it the best with my head under the hood. I have a code reader and checked, I have no visible codes other than it telling me about secondary fuel circuit high which I suspect was from showing off with my friends.
I did a cylinder balance test and again got 3 (PO269) and 8(PO284) which I have been told are very common.
I checked my ICP readings and it was 500~ and 11%
Pulse width for injectors was 2.50~
I did a KOER test and received no codes
Glow Plugs showed okay
KOEO (PO605)- Internal Control Module Read Only Memory error.
Exhaust Absolute Back Pressure was 16.2 at Idle with MBRP 4" Turbo back.
Also, I have noticed a drop of about 5-10 degrees in my oil temp and about 100 degrees drop in my EGT's although it has been pretty cold here recently (32 degree oil temp when I started her at 2 in the afternoon)..
I think it might be a bad piston skirt? I am guessing that from my experience with motorcycle engines but these are a totally different beast and that is why I am here...
I have 634,000 Miles and from what I have been told the engine has never been broken into so I would expect something like this myself. I am mostly looking for a place to start. Should I pull the oil pan and look for debris? (Oil was clean last time I changed it less than 2000 miles ago).
Should I pull the passenger bank apart and look inside? Is there a chance I am just hearing the noise due to the additive wearing off and me being used to the quieter engine?
My truck is currently stock and recently started making a knocking noise louder than it usually does. I researched and have found the injectors can make a knocking noise when not performing correctly. I took it to a local shop who hooked it up to a snap on scan tool and ran some tests. It passed the Buzz test but continually failed the contribution test on cylinder 8. I'm going to go home and remove valve cover and unclip the injector to see if the noise goes away. I'm sure hoping it does as an injector by the looks of things is definitely the cheaper option. I'm scared because if I was listening to a gas powered truck and heard the sound my trucks making I would assume it was a lower end noise. My truck only has 148,000 miles....
View 14 RepliesAfter running highway speed then stopping, the EBP valve is partially closing as you accelerate back up to speed. You can hear it in the sound of the motor, and you can see it on EGT's, which are rising quickly. This happens briefly then corrects. We unplugged the EBP sensor and the problem continued. Tube is clear.
If I monitor the EBP sensor, what values should I see if it is functioning properly?
So I just put billowed up pipes and changed the broken O ring in the turbo housing. Put everything back together and checked for a boost leak with the home made tester. Boots and everything ARE OK. I can hear air escaping from what seems to be the valve cover or intake. I realize that I am charging my crank case as well but it still concerns me that air is escaping from somewhere besides the CCV. I read the following forum and this guy had the same issue and after he found out he was charging his crank case he was no longer worried. . . . .
View 12 RepliesI just had my turbo and the EBPV on the pedestal rebuilt. Now I need to put it back into the truck. What is the procedure, if any, to adjust the EBPV? I only use the truck to haul a 5th wheel RV and the performance chip closes the EBP valve when going down steep hills -( EXHAUST BRAKE)
View 6 RepliesAfter checking my fuel bowl today for contaminants, I put the lid back on and then noticed a leak from the rear at drain valve. I know, I already ordered the orings. It was doing one drip about every three seconds with the truck running. However, I turned the yellow thing a couple times and the leak stopped. Not leaking right now. Maybe it wasn't shut from previous owner.
Second question.....After stopping leak and after routing my fuel drain hose, I decided to give it a try. No luck. Nothing out or drain. Based on my first fuel filter change, it may be clogged up. So, do I run wire from the bottom up? Or do I run wire from top (bowl) down? Just so you know, sucked the bowl dry with a vacuum device before I reinstalled the filter.
Iv heard a few things about changing the valve body. I tow a trailer so was wondering on pros and cons of changing this. And also what brands are recommended.
View 5 Repliesdoing injectors and pulled the valve cover, and noticed its not as clean as i expected. in the oil on top of injectors i noticed its got some grit in it. this cant be good and not sure how this debris got in there as i always change oil and air filter regularly( unless previous owner neglected). is there a safe way to clean this? Is this a normal find for you guys that have done injectors?
View 1 RepliesThe bolt that holds the dipstick on the valve cover. i have tried for ever to get this thing off. soaked it , got a skinny wrench on the nut underneath but think it might be stripped (1/2 inch grinded out a little). going to try and get a set of skinny wrenches tomorrow , mine bent. tried vise grips on top of the bolt and put a box wrench on the nut , and gave it my all. The damn thing won't budge.
Also, any tips on the rest of the valve cover bolts. I had to remove some from inside the fender well but barely got to them. My question is not getting these out but getting them back in. And how the heck to you torque these things??? The bolt i mentioned above is creating problem, and I only have so much time
I have what might be a big problem, the main harness on top of the drivers side valve cover I can't get undone, the bolt holding it together is stripped or the nut who knows? wondering if there is any way to take it apart otherwise.
View 11 RepliesI have this sensor unplugged. Is there a way to defeat this sensor so I don't pull this code?
View 3 RepliesI have a 02 power stroke 7.3, driving down the road the other day is started smoking a grayish white smoke pretty good. i let off the throttle and it had a real loud knock along with the smoke. oil pressure was good. i stuck it in neutral and revved it up kept smoking but the knock would go away at higher rpm. then all at once it would stop and run fine. then today it started doing it and wont stop now at all.
View 14 RepliesIf the fuel relief valve is stuck open would it possibly throw a P1316 code?
View 4 RepliesI had the engine out of my truck (7.3 with e4od) to do manifolds. Anyway, I got it back in and started it up. Since there was air in th fuel lines it had to crank a couple seconds but started up. I looked and now fluid coming out, then it sat for a few minutes running and I took it for a drive. While sitting in the driveway it wa smoking a bit. But I thought it's from the oil I got in the exhaust while drilling two of the manifold bolts and soaking the bolts with ATF/acetone. After about half a mile I thought that maybe it's more oil then that would cause... So I went back. I looked and the inside of the exhaust is covered with oil, and the rear of the engine is also.
When it was out I capped all of the open ports so I could pressure wash the grease off. Also, I flipped the CCV so I could do the delete. During instal, I missed the cap on the CCV and it was not able to breath. I think that maybe it built up pressure and blew the valve cover gasket? It looks like it's coming from the right cover on the backside; I had not taken this cover off while the engine was out. How much pressure does it build? Is it possible that it could have blown the gasket out? I have done the oil cap trick to test blowby and it always passed the test. What it could be? For the leak on the engine and why it's in the exhaust?
My 2005 with 160k miles has engine noise when cold.
I talked to a couple specialists who said it could be valve noise another said valve noise would not abate when the engine warmed up. He suspected piston slap. A valve adjustment is pricey and the local independents are afraid to touch it given the complexity and needed shim packs. If it is piston slap I would be disappointed after spending a pile of dough to still have the same noise.
Have I missed a possible cause?
I have a very small fuel leak in my 2001 F-250. I was going to just let it go until I needed to do other work (since I get 20mpg city and 25mpg highway), but I went to a "new" inspection guy, and he flunked me. So now I have to fix it. And for all I know, my mpg and fifteen other things will break when I try to fix this.
Today I spent 4 hours in the heat putting in two new o-rings on the water separator valve. But the truck still leaks fuel. Climbed up on top of motor while it was running and looked, but I don't see where the fuel is leaking out.
Online research suggests to me that the next most-likely culprit is a steel fuel line that wears through from vibration and chafing. Is that correct?
This truck is so eaten up with rust (came from salt belt) that I bought a LOT of fuel line stuff a year or so ago, so that when things started falling apart from rust, I would have the parts on hand.
Now I'm wondering whether I already have the part I'm likely to need.
So far, I have bought:
1. Dorman Fuel Supply and Return Lines
2. Riff Raff Diesel High Pressure Crossover (HPx)
3. Riff Raff Diesel Fuel Rail Crossover (FRx)
So my question is, am I likely to have something to replace the part that commonly leaks on these trucks due to vibration/wear/chafing ... or will I still need to buy another part?
I'm thinking that one of the two lines in item #1 above is the problem child...