Ford 7.3L Power Stroke (1999-2003) :: Knocking Noise At Idle


Aug 3, 2015

Noise goes away (or maybe it quietens to the point that you can't hear it) when you raise the idle just slightly. No smoking, no hard to start, no rough idle, no indicators of anything wrong at city or highway speed, nothing else out of the ordinary to report.

275K miles

[URL] .....

View 14 Replies

Advertisement

Ford 7.3L Power Stroke (1999-2003) :: Knocking Noise On Acceleration / Not At Idle Or Revving In Park

My 2000 7.3 2wd is making a knocking sound while accelerating. It speeds up as I accel and when I let off the gas it gets louder. It slows down all the way to a stop when the truck slows to a stop. I can feel it in the floor board a bit as well.

View 8 Replies

Ford 7.3L Power Stroke (1999-2003) :: Knocking Noise - Valve Piston Contact?

I have a late 99 7.3 that developed a knocking noise. I pulled the passenger's head and cylinder 5&7 have a spot where it looks like it came in contact with the valve. I'm not some master mechanic but am learning. What would be my next step to find why it hit the valve and to fix the problem?

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2000 - Knocking Noise - Cracked Piston / Rod Bearing?

Chasing this knock and I'm starting to get a little bit worried. So I'm looking for what I should do next.

Here is the truck info... 2000 F250 4x4 206k. . Swamps Diesel 200/30's. Terminator HPOP. GTP38R. EBPV delete pedestal. Banks wastegate. AFE stage 2 intake. RiffRaff FRX. 4" exhaust. Hydra chip. John Wood Auto. 6.0 Trans cooler.

I have a knock sound coming from the area of #8. It is noticeably louder in that area with a stethoscope. Its not any louder anywhere else (oil pan, block, otherside of engine, or front). Truck does not smoke and runs and idles great otherwise. Was thinking possibly the cackle/fuel knock issue these trucks have but with bigger injectors and the FRX could this even still be a possibility?! Anyways here is what I've done.

Checked fuel pressure and at idle it is 61/62 with any tune. At WOT on Econ tune it goes down to ~40ish psi. With the extreme tune WOT dived down to 28/29psi. So my thinking was maybe that injector got screwed up so...

Swapped #8 injector with #2 so the front injector with the back to see if either it had some bad o rings or isolate the injector as the problem if the noise moved cylinders with the injector. While I did this I put brand new O-Rings on those two injectors and popped them in. Got it fired up and the knock is still in #8.

Unplugging the injector with the engine running the noise seems to disappear. HOWEVER, when I use the stethoscope the knocking noise still sounds like it's there but very faint. Without the stethoscope I can't hear it. Also driving the truck down the freeway and letting it coast the noise goes away when the injectors get cut off.

Recently pulled off valve cover and checked the pushrods and rockers on #8 and all looked fine. At this point I'm thinking wrist pin, rod bearing or cracked piston??? Could it somehow still be a fuel knock?

View 9 Replies

Ford 7.3L Power Stroke (1999-2003) :: Knocking Noise Most Noticeably At Hard Acceleration Or Taking Off In General

I have begun to notice a "Knock" or "rattle" in the engine. I know diesels have a tendency to sound like that just from running but that sound is more of a "cackle" if you ask me.

I can hear the "knock" most noticeably at hard acceleration or taking off in general. It can also be heard during idle and every so faintly at deceleration with the torque converter locked so it makes me thing its mechanical due to the nature of the way the sound is audible.

I believe the sound is coming from the passenger side bank as that is where I can hear it the best with my head under the hood. I have a code reader and checked, I have no visible codes other than it telling me about secondary fuel circuit high which I suspect was from showing off with my friends.

I did a cylinder balance test and again got 3 (PO269) and 8(PO284) which I have been told are very common.

I checked my ICP readings and it was 500~ and 11%

Pulse width for injectors was 2.50~

I did a KOER test and received no codes

Glow Plugs showed okay

KOEO (PO605)- Internal Control Module Read Only Memory error.

Exhaust Absolute Back Pressure was 16.2 at Idle with MBRP 4" Turbo back.

Also, I have noticed a drop of about 5-10 degrees in my oil temp and about 100 degrees drop in my EGT's although it has been pretty cold here recently (32 degree oil temp when I started her at 2 in the afternoon)..

I think it might be a bad piston skirt? I am guessing that from my experience with motorcycle engines but these are a totally different beast and that is why I am here...

I have 634,000 Miles and from what I have been told the engine has never been broken into so I would expect something like this myself. I am mostly looking for a place to start. Should I pull the oil pan and look for debris? (Oil was clean last time I changed it less than 2000 miles ago).

Should I pull the passenger bank apart and look inside? Is there a chance I am just hearing the noise due to the additive wearing off and me being used to the quieter engine?

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: Loud Knocking Noise - Failed Cylinder 8 Contribution Test

My truck is currently stock and recently started making a knocking noise louder than it usually does. I researched and have found the injectors can make a knocking noise when not performing correctly. I took it to a local shop who hooked it up to a snap on scan tool and ran some tests. It passed the Buzz test but continually failed the contribution test on cylinder 8. I'm going to go home and remove valve cover and unclip the injector to see if the noise goes away. I'm sure hoping it does as an injector by the looks of things is definitely the cheaper option. I'm scared because if I was listening to a gas powered truck and heard the sound my trucks making I would assume it was a lower end noise. My truck only has 148,000 miles....

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: Cackling Noise At Idle And While Driving?

I had a piece of an exhaust valve break off and as one knows, that requires an engine rebuild. I have a rebuilt engine with new upgrades to my previous upgrades; fluid dampener, chrome moly push tubes, billet flywheel, T-500 HPOP, new front cover, up pipes, Dieselsite ball bearing turbo, OEM rebuild kit, comp cam valve springs and all new valves. Had some issues with the Dieselsite turbo that was worked out. Now I have a cackling noise at idle and while driving. The noise momentarily goes away for about 2-3 seconds while accelerating, (actually gets very quiet) but the noise returns. It doesn't seem to effect my performance, just very loud. I performed a cylinder contribution test, (passed) and injector buzz test, (passed).

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2000 F350 - Noise Like Exhaust Rattle Or Vibration At Idle

I have a 2000 Ford F350 7.3 with the auto and 262,000 miles on it. As far as I know everything is stock on this truck. It has been a great truck but lately its been making a strange noise. It almost sounds like an exhaust rattle or vibration but it is intermittent. Its not really loud it can be heard best in the cab at idle. I've looked all over on the truck and haven't found anything. I can't pinpoint where it is coming from. I tried starting the truck with the serpentine belt off no change.

I took the inspection plate off the bell housing and couldn't see any cracks the torque converter bolts appear tight, and the starter is not engaged while running. I've read a few forums on the torque converter going bad. It looks to me like its more the 99 trucks that had trouble with that. Did the torque converter issue carry over to the 2000's? Would a torque converter/transmission problem be intermittent?

View 3 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2002 - Loud Knocking - Smoking Grey

I have a 02 power stroke 7.3, driving down the road the other day is started smoking a grayish white smoke pretty good. i let off the throttle and it had a real loud knock along with the smoke. oil pressure was good. i stuck it in neutral and revved it up kept smoking but the knock would go away at higher rpm. then all at once it would stop and run fine. then today it started doing it and wont stop now at all.

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2000 - Smooth Idle But No Power

I purchased a 2000 excursion with the 7.3 a couple of weeks ago. The guy said originally in the add that it need #2 and #8 injectors replaced. When I went and looked at it he had already replaced them and said the it still has no power and needed the remaining 6 replaced. I purchased it as it was a good deal thinking I should be able to get it fixed for worst case a set of injectors. BTW the engine has little to no blowby and starts easy and idles great.

The problem it it will not build any boost (has external boost gauge). Actually the gauge only shows vacuum. With the truck in park or neutral you can slowly rev the motor to 2500rpm and all seems fine but as soon as you break past 2500rpm it sound like it is missing and starts blowing white smoke. The smoke smells like when a diesel heater runs out of diesel. If you try and drive it it has NO power and will not move out of its own way and will eventually start like it is missing and blowing white smoke.

The previous owner replaced the following:

#2 injector
#8 injector
UVC gaskets
MAP Sensor
Wastegate solenoid sensor

The first thing I did was start looking at the no boost issue and pulled the turbo. I deleted the EBPV while i was there. Also the turbine wheel was in very bad shape so i replaced the turbine wheel, shaft, seals, bushings and installed a new compressor wheel 5+5 wheel off ebay. Reinstalled turbo and the symptoms are the same. I also replaced the clamps on the spider with Tbolt clamps instead of the worm gear styles and it psi tested all piping and intercooler to 30psi with no leaks. Also the up pipes have already been replaced with the bellowed style so there are no leaks and it has a 4" straight exhaust.

I have since ordered oring kits for the injectors and also ordered the fittings for the fuel bowl so i can check fuel pressure. it has a new air filter, oil filter, oil and fuel filter installed.

The ICP sensor has oil in the plug but if i unplug it the symptoms are still there.

I have also used a scanner and the ICP pressure is approx 500psi at idle and the duty cycle is about 11% at idle. Also the HPOP looks to be new as it is very clean compared to the surrounding parts and i have checked the HPOP reservoir and it is full to withing 1/2" from the threads.

2000 Excursion
7.3
205000 miles

I am assuming that the injectors are original other than #2 and #8.

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2001- Rough Idle - Power Loss?

Dad has a 01 one ton with the 7.3 and isn't real tech savvy so I'm posting for him. He is the original owner and has been complaining recently about the lack of power. Particularly the upper end. He is having to downshift way more often and where he used to not have to. And we've both noticed a very noticeable shake at idle. Not a vibration but a true shake. He changes the oil every 5000 on the dot and I've gone and changed the air and fuel filter and ran hose and see foam and royal purple injector cleaner through it with no results. Truck is all stock with 225000 on it.

View 7 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2002 - CEL - Rough Idle - Loss Of Power?

I have a 2002 F-250 7.3, 159k on it. I bought it in March, ran AWESOME up till now. I was driving to work last week, check engine light came on, truck lost power and started idling rough. I have a buddy who works for a Ford dealer as a diesel mechanic, he came over with his scanner and laptop. #2,#4,#8 cylinders kept coming up saying possible problems are injectors, harness, rings.. He also did an electrical check, that all checked out. He told me to get injectors, so I got 4 injectors (yes I got the correct #8 injector), valve cover gasket, injector harness and 4 glow plugs.

The parts came last Friday, we did the job and it ran great. Drove it Friday night, Saturday, Sunday morning, no issues. Sunday afternoon we were on our way to a birthday party, truck started doing the exact same thing... Check engine light, rough idle, loss of power. After I got home from the party, my buddy came back over, put it on the scanner again, getting the same codes again. Deleted the codes, ran the tests again, same codes, deleted the codes, rant the tests again, same codes.

He said he is going to come by tomorrow with the box to check each individual cylinder.

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2001 F550 - Surge Off Idle / No Power

I have 01 F550 6spd 4x4. sounds rhythmic, smooth at idle but just over 1200 is a pattern surge but doesn't sound like one cylinder, cel is off, ICP and pigtail changed as it was leaking , no change. From what I've read duty on ICP and IPR should be about same % I've included the codes I've gotten, I have the epc disconnected right now as I thought it was a wastegate issue, checking the ICP plug next,anything I've missed? It had a cyl 8 contribution at idle which I hear is common? Will changing CPS work with that one? Think it's a grey one. There's no water in bowl I replaced filter, since replaced ICP, pigtail, and bleeding fuel bowl and new filter the codes are gone but still misses, will be checking uvch, injector buzz test showed no faults. Old diesel guy said to flood with Stanadyne fuel treat?

View 9 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2002 F350 - Rough Idle / Lack Of Power

I have a 2002 F350 4wd with the 7.3. I was driving the truck and all of a sudden it was running like crap. the engine light was on. after a minute or so the engine light goes off and the truck is running fine. then again starts running like crap. I am close to the house so I limp it home. runs like crap.... will barley climb small hills. engine light is on. get home turn it off... next day... starts up and runs great for 10 - 15 min. engine light comes back on... runs like crap.... my neighbor says "It's the crank position sensor" I replace it.... runs great for a month.... now it's doing the same thing......

View 9 Replies

Ford 7.3L Power Stroke (1999-2003) :: Power Breaking And Rough Idle When Stop At A Light

We have a 2002 7.3 f350 2wd this darn thing is now tripping me out. At first when ou start the truck its all good but when it warms up the idle is funky when you go to stop at a lite its like im power breaking and rough idle once stopped the idle is about between 800 and 900rpms at a stop really high idle but plenty of power on take off...

View 2 Replies

Ford 7.3L Power Stroke (1999-2003) :: Idle Roughly - No Power - Got Codes P1280 And P1316?

Started my truck yesterday and drove about 1/4 of mile and all of a sudden I lost all power but was lucky enough to creep back home. Had a friend put it on a scanner and it spit out P1280 and P1316 codes. My truck will start and idle rough but has no throttle response and no power. I changed out the CPS and ICP and the problem still exists. I got an infrared thermometer and checked the heat coming off each manifold and the driver side was reading about 200 while the passenger side was reading about 75 while at idle. Pulled valve pan cover off the passenger side to check and see if the harness came loose and everything looked fine. So my question is do you think this could lead to a bad IDM?

View 9 Replies

Ford 7.3L Power Stroke (1999-2003) :: Missing At Idle - Power Loss At 50 MPH - White Smoke From Tailpipe

My 02 excursion is missing at idle and jars the whole truck around going approx 50mph feels like good amount of power loss but still pushing 30psi boost, just got autoenginuity all injectors buzz fine on the test, contribution test show balance fault in cylinders 1&8, should I look for o-rings to be bad, uvch, cups cracked or what ----- turbo fine, hpop great condition, new IPR, new fuel pump and hutch mod, about. 250k miles on truck nothing else major showed up on ae.

View 5 Replies

Ford 7.3L Power Stroke (1999-2003) :: A/C Won't Work At Idle?

I have a 99 f350 and my a/c does not work at idle at highway rpm it blows cold. but once i let it sit and idle even on 1300rpm high idle it will now blow cold. it blows hot untill i rev it up aroung 2000rpm or drive down the road. I have charged the a/c system it has the proper about of refidgerant in it compressor gap is correct. Is it supposed to be like this? If not what are some things to check?

View 14 Replies

Ford 7.3L Power Stroke (1999-2003) :: Truck Sometimes Won't Go Into Idle

So for a while my truck sometimes and sometimes won't go into idle when I floor it and I've been trying to get the code and I finally got it it's tps high voltage so faulty tps??

View 1 Replies

Ford 7.3L Power Stroke (1999-2003) :: 2001 - Hesitates And Won't Go Above Idle Sometimes

I have a 2001 f350 4x4 edge programmer 330k miles. I bought it not running right and thought it would be a easy fix. I'm fairly knowledgeable with the 7.3. Original symptoms where it would run for 5-10 minutes lose power and quit. No restart until it sat for a few hours. P1211 was code, so I figure it's a high pressure oil problem. The truck has a new icp, Ipr, fuel pump, a receipt from dealer where they replaced 1 injectors o ring. I figure the o rings where bad. I replaced all of them.

1 injector was pretty bad the o ring was kinda tore up and disfigured, and 1 had new o rings. Why they would just replace 1 I'll never know. Well the problem still exists, it starts fine sounds good. It will idle 20-30 minutes then get sluggish if I give it any fuel. It's a lot better than before I can floor it and it will rev up and after a few revs it gets better again. If I unplug the icp the idle will go up and down and almost die. Trying to start warm it will just barely run at 4-500 rpm then quit unless I can get it to rev. Once it revs up it seems ok. Does that sound like a hpop problem or am I even on. The right path?

View 7 Replies

Ford 7.3L Power Stroke (1999-2003) :: Rough Idle - Stalls Out?

Truck has a rough idle and finally just stalls out. I replace the under valve cover wiring harness and put in new glow plugs. With valve covers still off I started the truck in the issue still persist. I went ahead and unplugged each injector and each time the motor had a hick up .

What am I pulling apart and replacing next?

View 13 Replies





Copyrights 2005-15 www.bigresource.org, All rights reserved