Ford 7.3L Power Stroke (1999-2003) :: Key Lock On The Steering Column Broken / Starter Never Engages
Jul 21, 2015
My truck was stolen over the weekend. Fortunately, it was recovered but they broke the key lock on the steering column and I'm having a hard time getting it started. I can turn the ignition all the way to the start position with my key or a screwdriver but the starter never engages. I'm sure I'm missing something simple but I can't seem to figure it out. Looking for instructions on how to get this started again?
View 14 Replies
Advertisement
I have a mostly stock '02 F-250.
The other day I parked the truck and as I was walking away I could hear what sounded like the 4x4 clicking on and off. I wasn't sure. I figured I would continue to run the truck to get more symptoms and come up with a diagnosis.
Later, backing out of the driveway, I heard what sounded like a buzzing/grinding noise, like something was trying to engage. It quickly went away.
The next day, the 4x4 light came on as I merged onto the interstate. I pulled over, tried switching the ESOF switch to get it to turn off. I never heard 4x4 engage or "felt" it. Re-starting the truck got the light to turn off. It hasn't been on since.
Today the truck made more buzzing/grinding noises. When I tried turning on 4 high with the ESOF switch I got no response. It went into 4 low and the light came on.
I re-started the truck. Tried putting it into 4 high again and the light came on. When I put it into 4 low the light quit and wouldn't come back on.
I run with my hubs unlocked and they were unlocked at the time, FYI. Also, I have air coming out of the vents, so no vacuum issues. I actually disconnected the 4x4 vacuum lines because I don't use the automatic locking future anyways.
I did do some work with my truck and boat during the flood in Louisiana and I took her through really sketchy stuff. My guess is that the ESOF motor is shot, most likely from being submerged.
View 7 Replies
Went to start 'er up, key spun forwards, power came on but no start, no click, nada. Turn key back and power stayed on, back forward and no resistance whatsoever power stayed on. Took screwdriver, jumped starter relay and viola away we go. Get home, get cylinder out of hole and the tip is broken off down in the column. BTW, had to disconnect batteries to shut it off. I drilled hole in the tip still in the column, insert screw and no come out. Must need to be turned somehow first I'm thinking.
View 14 Replies
1998 f250 4.6 4x4. In park the starter engages with key on . Ounce running the starter is still engaged in park and neutral. No engagement in the drive gears. Changed the ignition switch and neutral safety switch on the trans. When key is off instrument cluster is still on.
View 3 Replies
I broke my radiator drain plug got a replacement but how does the stock one come out? Is there a clip or something?
View 7 Replies
Just bought a 03, the seller showed me a exhaust leak. I found a bolt broken off, flush with the head. Looked at the passenger side when I got home, that side leaks too, and found one broken off bolt there too. Question, are these easy to do? As in, I have extracted broken bolts before, but they where on my V10 and I could just weld nuts to them and they came right out.
View 14 Replies
So I received my International bellowed up pipes from Riffraff and I figure I will start soaking all of the bolts with some aerokroil before I get started on monday and I see the very last bolt head near the up pipe is gone. The bolt is there but the head is gone and you can definitely see soot buildup everywhere near it. I don't know if I should order a new manifold for the passenger side and new bolts, order a driver and passenger side manifold and new bolts, or just order one set of new bolts and try to get take the passenger side manifold off and replace the one broken bolt.
View 4 Replies
I had a problem with this issue a few months ago, was 45 minutes away from home, blew the fuse to the starter. Switched another one in, blew it too. Had it towed to a shop, they did some diagnostics, felt like it was a short in the starter, replaced it and all has been well (as far as that particular issue) until this morning. Got in it, turned the key it cranked for less than a second and stopped. I pull the fuse, sure enough, blown. Swap it with another, it blows.
I know I have a bare wire in the column, the OD light wire is chaffed, I fixed it before but it must be worn again because I can get it to light up depending on positioning of the shifter lever and as I recall, every time the fuse blows the steering wheel is cranked to the left.
View 14 Replies
I just reinstalled my turbo and started the truck up to test it. After 15 seconds or so it shut down so I hopped out to take a look. I had about a gallon of oil coming down around the starter. All I did was reinstall the turbo (I had previously installed without the rear pipe hooked up). I can't see where the leak is coming from but this thing is not even remotely drive-able. My best guess is the pedestal somewhere?
View 11 Replies
Edit, I have also noticed I have been getting low on coolant, but without any noticeable coolant leaks. My engine oil still looks clean, where could the oil be going? How do I fix it?
2003 Excursion 153,000 miles - stock injectors, gt38r with new pedestal, Adrenaline HPOP, double transmission cooler.
I've noticed after some heavy towing with my camper (8,300 lbs), I've been getting a new oil leak showing up on my garage floor. I crawled underneath this afternoon and found three large oil droplets on the starter. See picture. What could this be dripping from?
View 14 Replies
Well I just "did" the glow plugs on my recently acquired 99 7.3 and while 7 came out with no problem, one of them gave me more resistance when turning than expected and then "snap". Now here is the interesting part. What actually came out is the threaded top portion of the outer wall, while the rest of the outer wall and the electrode are still in the block. I have done a lot of searching and it seems that usually the electrode detaches from the outer casing and the entire outer casing comes out with only the electrode or part of the electrode stuck in the shaft (usually due to carbon buildup or swollen tip). In this case though, the outer wall of the plug sheared in two, which seems to imply that the outer wall itself is what is stuck in the shaft and not the electrode. The attached picture hopefully explains what I am trying to say.
I can easily latch on to the end of the electrode with some vice grips, but even if I managed to get that out, I would still have the outer wall of the plug in the hole. At the moment I just screwed the threaded part back in to keep the everything from blowing out so I could crank the truck. It cranked right up and seems to run fine. My inclination is to just leave it as is and hope that 7 good glow plugs will do the job, as I have some nightmares about making things worse in trying to make them better. Any chance of the electrode falling into the cylinder if this much of the outer case is still there? How to remove stuck electrodes, etc. but none on a stuck outer casing?
View 9 Replies
I just bought a 99 F350 to replace my 01 F250 5.4 and I'm pretty stoked. There are several problem (some i knew about, some were surprises) 1 of which is the starter. The guy I bought it off said that every 100 starts or so (more like every 4-5) the starter sounds like it free-wheels but you just wait for it to stop, turn the key again (sometimes twice) and it engages and starts (although it takes a few seconds of turning over before it fires up).
I have a buddy with the same truck and he has had to replace his starter many times and I read in an old log book from the original owner that he had replaced the starter every 25,000kms (15,000miles). I am not the kind of guy who likes to fix things to have them break again.
SO my question is, WHY do the starters on these trucks keep breaking? What is the weak link? Is it possible to re-build one with better parts at home?
Is the problem partially because my batteries are only 650CCA and 750CCA and it takes more to turn this beast over? Could it be a bendix issue?
View 6 Replies
So I've begun to notice an annoying intermittent squeak/screech in my steering column while driving, obviously aggravated by the rough roads we've got down here. I can silence it tho, if I push in/up real hard on the steering wheel, so I'm pretty confident there's some bushing or bearing in the steering column that needs some lube or maybe just outright replacement.
View 7 Replies
Four months when you tried to start the vehicle sometimes you will hear the starter. Drive in gauge but not meet the flywheel. Sometimes it would take three or four tries to turn over the engine. Yesterday went out to start the engine turn the key nothing happen no noise nothing but all the lights were working OK..
The repair shop said it was not the starter but flywheel missing teeth. But they said the main thing wrong is a need of new battery terminals. They change them in the truck started fine last night Today when my wife try to start it then come home saying thing happen nothing no sound, no nothing. Am I dealing with a bad starter solenoid perhaps or a combination of a bad flywheel??
View 1 Replies
Any pic or wiring diagram of the starter relay that is mounted to the fender. I'm trying to start the truck finally but it's just cranking and I think I might have mixed up the wiring. Is there supposed to be a constant hot at the glow plug relay when the ignition is off?
View 14 Replies
Upon trying to start my 2003 f250, it keeps blowing the 15A "Transmission Range Sensor then to Starter Relay Coil" fuse. Initially the truck would still start if i did not use the aftermarket Viper keyless start. however, now it doesn't start at all and keeps blowing fuses. I contacted the guy that installed the alarm thinking it might be something on his end. He walked me through reconnecting the factory starter wires which would isolate the issue if it was something on his end. it's still blowing fuses. battery terminals are good and clean.
View 3 Replies
Batteries charged, connection & cables checked. After turning ignition switch, gauges on dash jump around & starts clicking in fuse panel. Top left relay then clicking sound from beside steering column on right side next to trailer brake box. Been having electrical issues & something draining batteries...had absolutely no cold start this winter. No decent mechanics here other than to be ripped a new one @ local dealership.
View 1 Replies
I replaced my starter with a new one from car quest yesterday, it was starting to turn the engine over slow. I checked the batteries, they were fine, so went for a new starter. After installing, the new starter turned fast and fine, started the truck ok, but I noticed a fast clicking sound from under the dash. Ran it home and tried to start it up this morning, turns over fast, the clicking sound is still coming from under the dash, but the engine won't fire. Just turns over. When it's turning over the check engine (and all the other dash) lights flash.
View 3 Replies
So I tried to replace my thermostat and housing and the housing bolt snapped off. Ok so I tried to extract that bolt off and the extractor bolt snapped off inside. I am guessing it might just be easiest to replace the water pump now? I am pretty much at the end of my mechanical rope which is short anyhow.
View 6 Replies
So I just bought a E99 f350 lariat. I wrecked the truck on the test drive and felt like the right this to do was to buy it. Finally have everything fixed and replaced on the truck and have run into other issues now.
While flushing the coolant system I started noticing that the starter was engaging randomly. After doing some research I found out it could be the GEM under the dash. Looked under the dash and I could here a sizzling sound and seen "smoke" /water vapor something coming off the GEM. And there is water coming through from the window/cab lights.
So. All the post I seen where from like 6 - 10 years ago. Where is the best place to buy a GEM? Will having the window replaced take care of the leaking issues on the window? What's the best after market cab lights? Cause I think they are leaking too.
View 6 Replies
My brother has a '99.5 with about 130k on it. It's extremely slow to startup even the the starter is spinning it over pretty quickly. I pulled my Edge CTS out of my truck to get some #'s off of his. At idle mine has about 700+ ICP, his has about 480. My IPR is about 14%, his is about 10%. The only other obvious things noticeable is that his oil pressure gauge takes 3+ solid seconds before it comes up. Once it's running, it's seems normal and ICP & IPR match mine under full acceleration. The only other thing that is odd, while cranking his volts drop to mid 10's but isn't turning over slow. Where to start?
View 6 Replies
