Ford 7.3L Power Stroke (1999-2003) :: Intermittent Throttle Response And Poor Fuel Mileage
Dec 6, 2015
I have read many different threads regarding the TPS sensor on the pedal and EBPV deletes on the E99 7.3L Powerstrokes. I am trying to troubleshoot some issues with my E99 7.3L. Usually on cool mornings and after not being started for awhile the truck will seem to be stuck in an Idle. This is an intermittent problem that doesn't always happen.
I cleaned the connections to the Tps and the IVS sensor and put them back in. No luck. On another note I am also seeing a reduction in fuel mileage and power like the truck is being restricted. I don't know if these symptoms are related or possibly their own issues. I am troubleshooting and possibly thinking it is the EBPV system that isn't working correctly. Considering doing an EBPV delete with a NON-EBPV Pedestal and Flange.
View 12 Replies
Advertisement
My friend has a F250. He was getting terrible mileage and the mechanic he took it to replaced the intake gaskets. After that the mileage went to 12 and he was happy. Now its down to 6-8, just highway. It seems to me the throttle response is terrible compared to my dad's 01 V10. And it sounds terrible. Exhaust manifolds aren't leaking that I see.
I've got AE and have hooked it up, but I'm really not very familiar with these trucks. I don't get any codes that would relate to anything. Had one trans sensor code but that was about it. Key on engine running test didn't say anything.
View 5 Replies
My7.3 is idling rough till I pull the fuse for the fuel pump them it will smoothen out I ran a by pass switch to us my truck but the fuel mileage is bad why
View 13 Replies
I just recently got my truck back, My father and I switched vehicles due to need and distance's being driven. 2005 F350 6.0, 164,000 miles
I couldn't wait to drive it again, I spent hours detailing and cleaning. Well I go to start and noticed it struggled to start, and didnt seem to be idling right. I looked under the hood and it was leaking fuel from the Regulator. I left it parked and never drove it since he last did. I read around on these forums and I bought the blue spring upgrade kit.
Now I notice it shakes at idle a lot more than it used to, pretty bad at times. Then upon driving it shakes even worse upon acceleration attempts, and has very poor throttle response. I have to put it nearly to the floor and even then the acceleration is nothing like it used to be. Most of my trip was highway at 60mph, and anytime it would start climbing a hill it would shake pretty bad with the acceleration. When i let off the gas to slow down before braking it stopped the shaking.
So I read around on here and I went back and used the factory bowl and valve for the regulator, still had the issue. Next I went back and replaced the blue spring with the original, still have the issue.
I just checked the FICM and it is reading between 48-49 during key on, cycle, and cranking.
Batteries are great
Alternator only reads 13.6 at 2k rpm idle, but have not had charging issues.
My father says he never noticed anything wrong with it other than it occasionally missing out. But I don't see how changing the fuel pressure regulator would have caused this. Especially since I tried every combination of oem and aftermarket parts, ensuring that all the connections and parts were installed correctly.
View 14 Replies
My 7.3 has no throttle response, the code reader says pass, and there are no codes, would it do this even thow it has a bad TPS?
View 4 Replies
I just bought my first diesel truck back in November. It's a 2005 F-250 with the 6.0L and the 5 spd torq-shift automatic tranny. Last weekend I drove the truck to South Carolina, about a 600 mile round trip from where I live. On the trip the truck only got 13 mpg! I wasn't towing a trailer and the truck was empty except for me and my suitcase. It's not loaded up with mods or anything, it's completely stock power wise.
I'm extremely disappointing, especially since a friend of mine has a 2006 F-250 identical to mine and he gets up to 21 mpg on his. What can be done to improve my mileage? I'm not a lead-footed driver, and the trip was done with almost all interstate and highway driving, very little driving on back roads or stop and go. If this is the best the truck will get, I'm going to sell it and buy a F-150!
View 14 Replies
I have a 99 F450 with the 7.3L in it. I brought it home the other day and parked it. Later I went to do something with it and I had no throttle response at all. I checked the wiring going in and coming out of the throttle position sensor. I have approx. 5 volts going in and the voltage sits at about .5 volts and rises as the accelerator is depressed on the outgoing wire. The other switch on the pedal is open and does close when the pedal is depressed, so it seems those are fine. I'm not sure what I'm supposed to have on the 3rd wire that goes to the TPS.
I have a Bully Dog tuner and it shows an exhaust back pressure sensor error and a couple of voltage errors to the accelerator pedal. I read somewhere that someone had an exhaust sensor short out and it starved the accelerator pedal from voltage or something like that but I do have good voltage at the pedal going in and out. I ordered a new sensor and tube.
If the exhaust pressure sensor was shorting out and I unhooked the wires could that make the pedal work if the sensor was the problem or would the accelerator pedal not work at all without that sensor being connected? (The old tube was somewhat plugged up and I saw it had a small rust hole in it)
If it's not the sensor, what else can I check? Where can I check under the hood to see if the wires from the TPS are getting power to where they need to? I assume they go to the computer and that tells the pump or whatever to give more fuel.
View 10 Replies
i got a 99 F250 powerstroke with 148K on its clock, i have a couple issues that i cant find a definitive answer for, 1 just started recently, Its an automatic and when it shifts into third around 40 mph the rpms drop to 1200-1300 or so, its done it since i got it, but recently it wont accelerate like it should or used to do, i have to put it down and make it downshift to recover.
Now I have no CEL. and it is still running perfect just has very little power, I do have a 4 inch turbo back exhaust and have a TS 6 position chip with i usually run in +50hp mode, but it does this in all positions. Now issue 2 is when its 30 degrees sometimes it will not start. It'll turn over with now fire. but if i cycle the key again it'll fire right up like a champ? It has a 4 month old starter and batteries and a month old alternator and i have tried several CPS' and Contently check the connections.
View 2 Replies
I own a 2000 F250 7.3 Powerstroke 4x4. The only aftermarket engine modification I have is a Tymar intake. The problem I'm having started about 6 months ago in a very erratic fashion. I would pull up to a traffic signal and as the light changed to green, without warning the truck would have no throttle response. The engine was running fine; there was just no response as I stepped on the accelerator pedal. Usually when I put the transmission in neutral, revved the engine a few times, the throttle would come back on line. This happened 4 or 5 times over the summer and then went away completely until today. Today it came back with a vengeance. At one point I had to shut the engine down completely to restore throttle response. It's a bit unnerving when it happens in the middle of a busy intersection. I was told that it may be the throttle position sensor. Does this sound correct and does it need to be replaced?
View 14 Replies
7.3 2001 model starts ok at 32-35 F. Feels a bit sluggish / slow response on the road. Reach a hill after 3-4 miles. Engine temp then beginning to go above low level mark. 100 meters up the hill, going around 30 mph there is a sudden surge in the throttle although my pedal is steady. Going back a few minutes later, on flat ground at bottom of hill and with no accelerator pressure, the engine suddenly stalls. Starts fine again after I stop. The same history actually repeated on two separate days recdently on the same hill. CPS is recently replaced. Had some jerking before that, but not the behavior explained above. Current CPS is Delphi light grey. Recent fuel filter change and oil change as well
View 14 Replies
Finally had a chance to pull the coils for inspection, and give the truck some very needed plugs. anyways, since i got it, the truck on initial start will rev itself up to about 3k rpms. it will almost always die after that rev. with the MAF sensor disconnected, it will rev to about 2k rpms, and the idle, if you can call it that, around 1k rpms. it will buck, jump, spit, burp, chug, pop, blow, and phew noises the whole time. I can rev the truck at this point but the throttle repsonse is poor. it does rev with a slight misfire, but no popping like what it does at idle. the exhaust has been dropped before the cat, so i know its not a plugged cat. i feel it could possibly be a sticking idle control valve allowing air past behind the MAF sensor causing this crazy scenerio
View 7 Replies
Is it possible bad spark plugs and wires affect poor acceleration and bad throttle response.I have no error codes and the engine is rebuilded.Idling sound good.Difficult to start engine first time(seconds after-easy to run the engine).
Tyre size 195/65/15 winter?
View 1 Replies
Just joined today, I have a 2003 550 7.3. New HPOP, 3 new injectors, new seals on others, new fuel pressure regulator, new fuel pump, sending unit mod to eliminate filters. 733 HPOP pressure, 65 fuel pressure at idle. Truck runs out of fuel pressure after its warmed up and driven about 20 miles. Haven't checked voltage at pump while driving. I had taken it to a seasoned tech of 20 years and he had replaced HPOP and 2 injectors and it does start better but problem is still there.
View 14 Replies
Looking for some tried and true fix to make these parking brakes hold just a little? Winter coming and with a six speed would like some resemblence of a brake....short of a brick in the drive. I have adjusted.....no luck. New cables ( thinking maybe stretched)..no luck. Shoes are new. Did notice levers where cable attach look to be worbled out.....gonna try to tighten that are up a little to see if that works but.
View 7 Replies
So while driving just now the truck went down to idle and no matter what I did to the gas pedal the throttle would not change. The truck didn't die but would just sit at idle. It was like the gas pedal wasn't connected. About a minute later it surged a little and then I was able to drive like normal.
History- last week while at a red light the engine surged and then almost died. Light changed and I hit the gas....and stayed at idle...then died. Restarted and died two more times and then just drove like normal. Changed fuel filters and and checked fuel pressure. Under boost it was 38-40 psi. Idle it was 45. Cac tube replaced due to cracks.
View 14 Replies
I recently bought a 1983 Ford Ranger Diesel pickup truck (2.2L Mazda engine, manual transmission). The dealer said to expect a little above 30 mpg on fuel mileage but the two fill-ups I've done show an average fuel mileage of 22 mpg. About half of these are highway miles.
I thought diesels are supposed to have good mileage. Is this typical for my year and model truck? Is there any way to increase the mileage? I just replaced the air and fuel filters and also changed the oil and oil filters.
View 9 Replies
I am curious to see what you think. I had my car chipped by upsolute. For as long as I have had it and even when I took the chipping off, restoring my car to stock, i was getting pressure spikes, lousy throttle response and lousy gas mileage. For a while, I was going to the dealer every other week or so, trying to find out why my car was kicking into limp mode. Upsolute said it was the car and the dealership said it was the chipping.
Anyway last saturday I was inspecting my air filter and airbox (nice little pile of sand and a couple of leaves in there-I am sure that didn't work my mileage any). I moved the airbox a little and the hose which connects to the airbox underneath the air intake ductwork, fell off the airbox on its own. It was never clamped in place. I am told that is the hose that goes directly to the MAF Sensor.
My question, if all else is tight, do you think I have found the source of my over pressure and lousy gas mileage problems? The car certainly feels like it. I went and tightened up every hose connection I could find. My car feels like it has a new motor with a healthy growl to boot. Mileage appears to be up as well. What do you think? I thought about restoring my chipping but I wont do that.
One is that I have a very good extended warranty still in effect and don't want to risk losing it. They would love to hear the car is chipped. Then its good by policy. The other reason is that the guy who chipped it said he would put it back in but would not remove it if I am wrong. The dealership said they could not and would not restore my car to stock even though I cannot believe they don't have the tools around to do so.
View 1 Replies
So I was driving to work and the truck lost throttle response. There was very little of it! Came to a stop then it didn't barely want to move, pulled over then it died on me! No clue what to look at! 2005 6.0 232k miles
View 14 Replies
I just completed installing rebuilt injectors in #2 and #4. for the 2nd time. The first set had failures with those two. After assembly, the engine runs rough which is understandable considering the air introduced. I can run the RPMs up while in neutral or park, however; there is almost no throttle response in drive or reverse. It will barely move and only slightly raises the RPMs. I am unable to drive it to get the air out until this particular issue is solved.
Prior to the tear down for #2 and #4, the throttle response was fine.
Current Codes:
P0272 - I am hoping this would go away once the air is gone.
Software:
AE w/ Ford Bundle (New to me)
Buzz test is fine
Power balance looks great
FICM logic and power are good
Skills:
DIY w/ limited electrical knowledge
Recent Mods in last 300 miles:
New heads
ARP studs
ICP
IPR
FICM w/ Atlas 40 from FICMreapir.com
Injector harness
HPOP
Chemical flushes
Oil Cooler
Leak Proof Ball Tubes
Stand Pipes
8 Rebuilt Injectors
Batteries
MAP Sensor
New Turbo w/ updated supply and return
All associated gaskets and orings replaced with the above
All OEM where available, except injector rebuild service
View 5 Replies
I've been having rather slow throttle response with my 6.0 f250 diesel at lower RPMs. Obviously, this is to be expected to some point.. Whether I'm cruising on the highway or through the neighborhood, if the truck is at lower RPMs and I try to accelerate, it doesn't want to. In order to get it to accelerate, I have to press the gas down enough to downshift it then it'll take off.
The truck doesn't have a loss of power at higher RPMs, it takes off like a bat out of hell. I've put 175CC injectors in, tuned it, power max turbo, EGR deleted / studded, etc. It's almost go out with acceleration, or go turtle power with acceleration.
Oil pump was replaced a couple years ago. This problem existed through it all, and it's rather annoying. The truck doesn't want to produce any low end power. If I try to hit the gas enough to accelerate but not enough to force a downshift, I'll just blow smoke, spool the turbo, and barely accelerate until I down shift or push the truck through it. Turbo PSI is roughly ~15ish-20ish during the sluggish transition.
View 14 Replies
2007 F350 6.0L 230,000 miles
Yesterday, while driving home from a weekend out of town trip, all of sudden lost throttle control. Just went to idle while at cruise speeds, could pump pedal and no response. Then got pedal control back and seemed to run normally.
This happened several times. Hubby suggested moving the adjustable pedal which I did slightly. Although I was not using the cruise control, we had a sense that maybe it was engaging??? So I hit the off button a couple of times. After these two interventions, drove the last 80 miles home with no further incidents.
Today, we checked codes and had a PO231, Fuel Pump Secondary Circuit Low. I don't think that is our problem with above based on research, but we will look into fixing that too. We are thinking TPS or a position sensor on the accelerator pedal. We could replace those easily ourselves.
View 14 Replies
