Put in my new S&B intake today and when I stomp on the gas I am getting a loud shuddering noise from the intake when I change gears. Also sounds like a squealing sound sometimes. Doesn't sound like other trucks that I have heard. What that could be?
View 14 RepliesWhen I accelerate i get a loud squeal until my truck changes a few gears. Its only when I accelerate and only if my trucks warm and has been running or a few minutes. Cold start it wont happen right away. What it is or could be. Changed my serpentine belt that didn't work...
View 7 Replies2002 F350 single wheel 4x4, 280k miles chipped with a 6
My problem first started when the bottom of my sending unit broke off in tank causing me to run out of fuel at 1/4 tank. I dropped tank and repaired. A week later I noticed fuel dampness on my tank and discovered I crossthreaded cap on sending unit. About this time I started getting a shutter at slight acceleration only and a harder hit at idle. I thought air in lines so I dropped tank and reassembled. No air in line at all now but I still have a shutter so I replaced fuel filter in case of obstruction. No luck. Now since I have owned truck it has been a pain to crank in cold weather if it wasn't plugged in over night. It has been hard lately even in moderate weather since shutter started so I replaced both batteries today.
I replaced the ICP today also because I noticed the other day when there was oil on and around harness to it and when I unplugged it today the truck changed idle and there was oil inside. After I changed it I took it out and it still had the shutter and sound of a miss. At about 8 miles in it just died going down the road. I coasted to the side and it cranked right back up and drove home. The shutter doesn't fill as bad but there. Also I live in the mountains and on my way home after cutoff I had chip in Stock position and had to put peddle to the floor to climb hill. I've never had to do that. I'm getting worried I work for a living and caint keep throwing money at it aimlessly. I'm thinking at this point IPR or CPS. But I'm no mechanic so I could be completely wrong.
Picked up my truck from the local transmission shop yesterday and on the way home (less than 3 miles away), I noticed the ABS light was on. I turned around back to the shop but the guy behind the desk couldn't pull the codes (his mechanics smart with codes don't work Saturday). So I will head back tomorrow when his code-smart dude is back but was wondering is there anything they could have done during the tranny install to muck up the ABS system? Or do they need to do something because of the new transmission?
I checked the #15 5-amp fuse under the steering wheel but it looks good. Truck runs good to me and shifts fine in the 10 or so miles I drove it yesterday but I'm not savvy with transmissions or ABS.
So just got a new pcm installed since i fried the last one anyway. I had a new trans installed almost two weeks ago factory 4r100 now i have a p0720 code. Id take it back to that dealer.
View 8 RepliesShut my truck off for about 15 minutes and wouldn't start back up. Installed new fuel filter. And gonna try changing cps. Torque says Rpm 180
Ipw. Bouncing between 600 - 3000 Hpop. 250 while cranking Voltage 10.9 while cranking. Ipr starts about 15% and slowly climbs to about 88%
Fuel pressure about 65%
Tried unplugging cps. Gonna check oil now though I check it every time I fill up and it never uses any.
Title says it, I just installed my Hydra Chip, now my edge says it cant communicate with PCM. I have checked all the connections on the edge, all is good. I planned on just using the Edge only for gauges. Will it not work anymore now that I have a Hydra? If not I will just sell it and buy an Edge Insight, so long as that will work.
I think its the Edge EVO 2, its this one.
How many gallon tanks were installed in the E99s?
View 6 RepliesWhat does it mean when you find oil in in the cold air intake, is this normal?
View 14 RepliesWhile doing a visual inspection I noticed that the AIH hot wire (captured nut wire) had broken off and was laying loose. I removed the wire from the relay and made a new 8 gauge wire, I connected it to the relay and was about to add it to the AIH when I got a healthy spark ( it touched the ground wire ) and yes the truck was not running and the key was out at the time.
This sounds to me like the relay has gone south, am I right??? I have a new OEM relay to install but I have a question. In what order are the wires and ceramic fitting go on the AIH post???
Noticed a while back that the plug for what I assume is the air intake temp sensor is looped. I assume because I can't find the sensor anywhere. how critical is the sensor? The new S&B has a hole for it so it's either gonna need a new sensor or a plug. The local autozone has one for 16.99.
View 12 RepliesDumb question but how do I remove the air filter intake from the turbo Its a little oily there from a fuel or oil leak but I dont see a clamp holding it on the turbo?
Also what is the e clip? Is it the little thing holding the wastegate rod on the exhaust turbine? Can I just pull the rod up off the clip?
I own a 2003 E450 (transit bus conversion) with a 7.3L w/ California emissions. I recently noticed I have a considerable amount of oil in my air intake going back all the way to my turbo starting where the crankcase breather tube attached to the air tube. The breather seems to have some sort of filter housing that is attached to the top of the valve cover. I removed it and it appears to be fairly heavy as in if it's a filter, perhaps it's full. If I'm getting oil into my air intake from where the breather tube comes off that housing and joins in my air tube back to the turbo, could that filter or housing have gone bad? It appears to be a dealer stock item only for 225. I've saw on the web people posting "reroute kits" for the 6.0L but nothing for the 7.3. Does this part simply need replaced or could I be facing a separate issue as to why I'm getting oil in my air tube?
View 14 RepliesAir Intake Heater Plug Code Eliminator P0541
In conjunction with the AIH Delete Plug??
Ok let's start I have a 1999 f350 7.3 4x4 Work Model that I'm have some odd transmission problems. I drove it 20 mins to do a 2hr job no problems finished that got in took off I few seconds down the road it was like the tranny just dropped out no sound just reved no gears at all. So I shut it down tried to start again would not start in park without pulling up on the lever which had experienced here and there for a good while. So got it started went in gear took off same thing went popped out no gears. I started it again this time used reverse same thing as drive so got it where I knew I could leave it but now it would not start in park anymore at all. Next day picked up a neutral saftey switch changed it now it starts in park every time but still starts going looses the gear then have no gears shut it down sometimes had to wait a few then again same issue.
View 14 RepliesDriving along today my trans started doing some weird stuff. It lost all gears. Forward and reverse. If I turned the truck off and let it sit a while it would go again for awhile then loose drive again. When I got home I checked fluid level and did KOEO o/d off and back on. I drove it around the block and it seemed ok, so I went on my way. After about 20 min I noticed the OD light flashing. I checked codes and It had P1754-ccs.
View 14 Repliesmy first diesel, and second 2002 f250. I picked up my 7.3 4x4 automatic CCSB last week. 202k on the odometer. I need to change the air filter but idk what to use. I don't think it's stock. The side of the air box says aFe. What the part number for the filter is? I don't see one on the filter anywhere.
View 6 RepliesIv heard a few things about changing the valve body. I tow a trailer so was wondering on pros and cons of changing this. And also what brands are recommended.
View 5 RepliesOk, the swap is all done and I have an engine in the truck that has compression in more than (7) cylinders.
2002, 7.3, 4wd - ~120k miles on trans. Fresh fluid (Mercon V).
Put the gear selector in reverse and it goes right into gear with the normal tug and functions as it should. Put it in low gear and it also appears to work fine. But, when selecting '2' or 'drive' it feels almost like its engaging 2 gears at once?? There is limited forward motion and it feels like the brakes are on. I have not driven further than the driveway yet, but I have a long driveway...
The OD light does not come on. I am not getting any codes from AE, but I really don't know how to use it for transmission stuff (I've been using a different scan tool that I no longer have).
We have not put the bed on the truck, so no tail lights - but 3rd brake light has new bulbs and was working (didn't check this AM though... )
I have a couple other codes, CEL, 'check gauges' and no tach. Gonna start another thread for those issues, I'll put a link here in case its related.
I am changing the rear Diff fluid in my 1999 F250 Super Duty with limited slip differential. I have read in the manual that 8 ounces of friction modifier is required, ford dealer said it only required 4 ounces. I bought 8.
Also I asked for a inspections plate gasket and ford said use silicone... When I removed inspection plate it had a gasket. So, silicone or gasket or both? Differential capacity is 6.9 pints 75w/140w synthetic.
My shift indicator switch on the trans seized up, so a local trans shop replaced it for me. Now I get no low range when I select it. I understand it needs to see the truck in neutral to do this, is there a simple adjustment? The trans shop is a long way away.
View 2 Replies