Ford 7.3L Power Stroke (1999-2003) :: ICP Is Running Low - 460 To 480 At Idle And Bouncing All Over The Place
Jun 10, 2017
My ICP is running low, 460 to 480 at idle and bouncing all over the place. It doesn't get above 2500 or so at WOT acceleration the ECM is throwing a "pending" DTC for low ICP. I removed the ICP regulator solenoid coil and cleaned the inside, filled the connector with dielectric grease and reconnected. That worked for a while but it's creeping down again. I'm going to pull the ICP regulator and clean and rebuild it as soon as I figure out how to do it w/o taking the whole HPOP assy off. How to determine if the root cause is the ICP reg. or the HPOP? Regulator duty cycle is running 15-20% at idle and less than 30% the rest of the time which makes me think it's the HPOP.
View 14 Replies
Advertisement
This morning my 02 decided to turn the ABS light on, and start bouncing the speedometer. plus, the OD light is flashing when stopped with foot on the brakes, but the trans is shifting fine. Nothing changed on the truck except almost 3 inches of rain fell last night. Will AE tell me if the VSS is going bad?
View 14 Replies
2002 e350 7.3 diesel transmission... At 7 miles the speedo began bouncing and truck drops into second. Parked it 30 minutes, stated up no problem until 8 miles and the it started again. Have checked most of the electrical, changed speed sensor and transmission position sensor. Only error code 2-3 rd gear mismatch.
View 11 Replies
I have been "fighting" a front tire cupping problem on my L99 F350 Dually 2wd since I have owned it.
I got LOTS of paperwork with it, one of which was a service ticket from the dealer where it was bought new (with VERY low miles on it) saying several passing motorists had informed them that the front tires were bouncing down the road.
I have read this service complaint several times and I now feel that has something to do with it. I bought the truck with 70k on it some 8 years ago-the PO had installed EXPENSIVE Michelin XPS Rib steering tires on it and they were already destroyed by cupping.
I replaced all 4 shocks, and all 6 tires, begged the folks to FIND something wrong/loose/worn out on the front suspension/steering and they found nothing, they aligned it. THAT set of Cooper Discoverer HT tires did exactly the same thing, except I spent a lot of $$ having the tires rotated.
Now I have a set of Firestone TransForce tires on it and its been to a HD truck shop where I begged them to rip into the front end and FIND something wrong-THEY DIDN'T. THEY installed camber bolts and aligned it, yep, you guessed it STILL CUPPING!!
So, now I'm thinking is it possible that the wrong coil springs were installed at the factory causing this bouncing that the original owner reported to the dealer? I have now destroyed 2 more tires and getting tired of it.
View 9 Replies
2003 F350 6.0 with 290k+ ... It has a skip in the engine at idle and running. At times when running down the road skip seems to get worse. Changed both fuel filters, didn't work. Truck start up is normal, no leaks, and flashing no codes.
View 3 Replies
I have a 03 F-350, 7.3L. There is a slow oil leak that only leaks after I've run the truck. In other words, it doesn't just sit and leak overnight. I'll park it after running, and the next morning I'll notice a small pool of oil, approximately 2" in diameter. The leak appears to be coming from the oil pan area. I degreased the entire oil pan area to get a better visual of where the leak is coming from. I can see oil trailing down the front of the oil pan and the rear of the oil pan. Does this sound like the gasket? Or, what else could it be? I'm praying its not as bad as I think and need to replace the gasket.
View 3 Replies
I have a 2003 F250 7.3L. I put new injectors in my truck four months ago and all of a sudden, I have 2 cylinders not working correctly, making the truck to run really badly. I sent the 2 injectors from the bad cylinders back for warranty and they replaced both of the injectors but nothing was wrong. I put them in and the truck still runs badly. I have a new fuel filter, new ICP, new CPS and glow plug relay. I cannot drive the truck, it smokes white at idle. I can unplug each injector at a time and cyclinder 5 does not change how the truck runs
View 14 Replies
I have a 2001 ford 7.3l powerstroke diesel. When I first noticed the problem I was towing a trailer going up a grade and got into the throttle almost to the floor and noticed a loss of power and the service engine soon light flashing extremely rapidly a few times and never came back on. I made it home, still lacking power but not running rough. I drove the truck to work the next day and the truck was running rougher and loosing power. It ran great through lower RPM's but seemed to trip as soon as you gave it over half throttle. eventually the truck wouldn't run right at all and lacked complete power. It idled rough as well. My mechanic threw the computer on it and it said injector pressure reading too high or too low.
I was told to replace the IPR on the HPOP and I did. (I also replaced the fuel filter and changed the oil). After replacing the IPR it ran great, had full power! then it began to slowly die like it did before until it sounded like it was running off 4 cylinders again. I pulled the ipr out, cleaned it and changed the oil again. It seemed to clear it up for an hour and ran great but then began ran rough again. I also replaced the CPS sensor. I feel like its not getting enough fuel or something, im just wondering if it could be the ICP or the lift pump. There is no check engine light at all. Its just got me stumped because cleaning the IPR clears everything up.... temporarily.
View 14 Replies
Where I should start? My 7.3 is running but losing all power. Pumping the fuel pedle will get it started and it will run for a few then lose everything again. Should i just drop the tank and check the sending unit and intake and filters first then work my way up?
View 5 Replies
2000 F250, 7.3, 170K, running rough, knocking loudly, missing, shaking, no power to get up driveway, intermittent, no codes spit out at all. No smoke visible, no leaks visible, New fuel filter, air filter, update cam sensor, new fuel rail lift pump, new uvc harness, new glow plug relay.
View 14 Replies
Well, I was headed out from work this morning, on my way to fill up as I was a bit below 1/4 tank.
Truck was running good, like normal, until after 5-6 minutes, when it started running rough and had no power. Worried, I pulled off the side of the road. As I did so, it died, and wouldn't start again.
I whipped out my phone, pulled up TorquePro, and ran a code check. Nada. Well, it sounds to me like it's not getting fuel possibly, so I figure the best way to check, is to drain the fuel filter bowl, and crank it some, and check the bowl. No fuel in bowl.
Wifey came to pick me up with the can of diesel I keep for starting my forge (had 3 gal maybe?). Poured it in the tank, cranked it, no start. Still nothing in the bowl.
I'm taking her to work now, so she won't be late, then I'm headed back with a full can of diesel.
If that full can still won't get it, should I keep shuttling diesel cans, or should 8 gal or so be enough to get it back to the fuel pickup level? And if it's not fuel level, what else should I start checking on the side of the road?
View 14 Replies
I have had this happen twice now. Starts fine, idles fine, then either sitting or just driving a block or two it starts running very rough, no smoke that I remember seeing, and now no power. Barely makes it up a hill. The first time I thought is was related to the heavy rain the night before. I had the tow truck coming and decided to try it again, this was after a few hours sitting. Ran perfectly. The second time, no wetness/rain, pulled away from the house and in a block or two, same thing ... rough, no smoke, no power. Pulled back into driveway, turned off for a minute, restarted and ran fine. Ran perfect today. What is the best injector cleaner to use in the fuel?
View 3 Replies
2002 F250 7.3L suddenly idling and running very rough, and doesn't have any power. Truck has been running perfect, it's my daily driver, and just put a couple hundred miles on it yesterday with no problems. I had been having some transmission issues when I tow heavy so I bought a new transmission yesterday. This morning I pulled the truck into my garage to change the transmission. Again truck ran fine, no signs of any issues before the trans swap. I changed out the transmission, which included unhooking the trans wiring harness from all the various sensors, and unbolting the starter.
I didn't mess with anything in the engine bay except for unhooking the batteries. I had also repaired the overdrive button wires, as they had been pinched in the steering column and the button wasn't working. When I got everything hooked back up I cranked it up to get the trans fluid flowing through the transmission, it started right up and idled good. I had it running for a few minutes and it was beginning to make a little more noise than usual. When I started to back out of the garage it was getting pretty rough, almost like it was running out of diesel. I put it in neutral and gave it some throttle and noticed I was getting white smoke out of the exhaust and could smell diesel pretty strong.
I checked my injector resistance at the valve covers and got around 4 ohms +/- on all of the injectors. I rechecked all of the clips and harness that I had messed with. I took a look at the ICP sensor and it has oil in the connector which I know can cause a rough running condition in some cases. It looks like it has had oil on it for a while. I unhooked the batteries again for about 20 minutes to try and reset anything that may have messed up. I checked a bunch of connections under the hood to see if anything was unhooked or loose.
I also cleaned up the connector on the ICP sensor. I started the truck back up and it idled perfect so I pulled it back out of the garage and headed down the driveway. It almost immediately started running rough again and barely had the power to go up a small hill. I pulled back in and tried unplugging the ICP while it was running, which made a slight difference in the idle but still very rough. I plugged it back in and the idle progressively got worse until it was chugging really bad. I shut it off after that and haven't messed with it again.
What might have happened? Could it be a bad sensor or transmission position sensor in the new trans? Is it just coincidence that this happened with a transmission swap? I am going to get a new ICP, but if there is anything else I can try/check before I can pick up the ICP on Monday let me know.
View 1 Replies
I was wondering if fuel injectors throw a code when it goes out. I have a 02 7.3 been running rough when you accelerate bogs down and looses power not sure but sometimes gas light would come on knowing I have gas in it could that be a sign of the sending unite and that's why it runs rough..
View 3 Replies
No start. Changed starter solenoid. Changed starter. Now it runs although when I turn the key to the off position and remove it the engine continues. The only way to get it to shut down is remove the small wire from the positive on the battery and then turning the key to the off position or vise versa. The machine seems to be pulling power even when completely shut down. The batteries drain power with "nothing on" i d m shot? Someone stop me before I go to the dealer.
View 5 Replies
I bought a 2002 body with a late 99 engine with lower miles a couple years ago. I knew it had an oil leak when I bought it. My other truck had a turbo pedestal leak. This truck has a small pedestal leak but it's not that much of an issue as there is little oil in the valley and next to nothing running down the back of the engine.
The other leak is getting worse. It has been leaking somewhere up front and coats the main steering arm off the steering box, the lower rad hose and the rest of the steering linkage. Last night after driving around 100 Kms I have oil running out from under the engine across the floor.
I changed the LPOP after thinking the front leak was from there. Unfortunately i don't think it was.
I am hoping it's the oil cooler and not the HPOP. One other thing is before yesterday's trip, I installed my homemade ccv mod off my other truck. I don't think the leak is coming from that either.
View 14 Replies
A little background information is that I was towing a large gooseneck trailer about a year ago when half way to the destination the lights quit. Not just the trailer but the truck tail lights, turn signals and everything except the headlights. Well after getting there and unplugging everything it stayed the same. Well on the way home without the trailer the lights began working again. All the truck lights acted as it never happened. No blown fuses or anything.
Well things are are going ok since then but I can never get running lights to any of my 3 trailers to work. Turns and brake lights are fine. What gives? All the fuses are fine and the truck running lights work just fine. One thing I have noticed is that on my horse trailer I have the little led lights on the sides operational... I would have assumed these to be the same as the tail running lights.
View 3 Replies
Traveling right now. Limited access to FTE.
On the way to the airport this morning at 4:30 am, the engine simply did while running down the interstate. Absolutely no symptoms leading up to it. Turns over fast but will not start. White smoke from tall pipe while trying to start.
I unplugged the fuel bowl heater and checked the IPR tin nut and the ICP sensor connections... Nothing obvious.
Problem was CPS and the engine is now running fine again.
View 14 Replies
I have a 2001 F350, 7.3. My service engine light came on and immediately the truck started to run rough and lose some power. I've checked the under the cover connections and they were both connected, I replaced the cam position sensor and I still have the same problem. The worse part of the hold thing is that there are no codes stored so I'm flying bind. Where to go next.
View 8 Replies
2003 CC 4x4 ... I am pretty sure I know what is going on, but I wanted to start a thread for when I confirm it. I am driving to work this AM and I hear the door ajar chime and I think to myself, uh oh...gauges all look good, there are no lights illuminated on the dash. I get to work and turn the truck off and my fan stays on. I think the ignition module is going bad. Either that, or my remote start is going on the fritz. I will update when I find out more.
View 3 Replies
My brother is having a issue with his 99 F350 diesel automatic tranny pu. When in manual 1rst gear the engine stumbles and runs like crap. In drive or 2nd gear it runs fine. He's getting a code for a bad cam sensor. A new OEM and aftermarket sensor has been tried with no solution to the engine problem. What might be going on?
View 1 Replies
