Ford 7.3L Power Stroke (1999-2003) :: Hold Gear Selector Towards Park To Get Reverse Lights To Come On
Feb 5, 2011
I have noticed that I have to hold my gear selector towards park to get the reverse lights to come on. Also some times I have to hold it towards park to get it to start. I changed my tranny in Dec 2009 and occasionally it would do this while starting, just noticed the reverse lights about a week ago. Tried moving the cable where it attaches to the tranny a couple of serrations each direction. No luck. Is there another place I can make an adjustment?
View 14 Replies
Advertisement
I have a 2008 F-150. When moving gear selector from park to either reverse or drive, trans has a delay engaging. After engagement, it runs fine, shifts ok, downshifts ok....
View 7 Replies
Last November I forgot to plug my truck in and it got down to 0, my girlfriend tried unsuccessfully to jump start it. When I got home I jumped it and got it running. I took it down to a heated shop to troubleshoot the glow plug circuit. I discovered it was not getting 12v to the glow plug relay. Also I started it and tried to back it up in the shop, when put in reverse it killed the engine, not lugged it down it was like you shut the switch off.
Also I discovered if you turn the lights on it kills the engine immediately. It will not crank with the lights on either. So far I have replaced the computer,ignition switch,batteries, and cam positioning sensor. Now comes the weird part!! I decided to get it running and pull the bulbs out of the back up lights I pulled the drivers bulb first then the passengers side bulb. When I pulled the passengers side bulb it killed the engine.
It is not my daily driver so it still sits in my shop. I have a hunch it's a ground issue but I've checked and cleaned up all the grounds I can find and it still has the problem.
View 10 Replies
I'm wiring a backup camera and I need to energize a wire with +12v source that turns on when the truck is placed into reverse.
If I can connect the wire to 12v which automatically energizes when the truck is shifted into reverse, the backup camera will turn on automatically.
Surely I could pull the signal from the reverse lights, but I'd like to find something in the fuse panel because that is where the wire terminates and I'd rather not extend it all the way to the reverse lights on the back of the truck.
Where's a +12v source in the fuse box area under dash that energizes when the truck is put into reverse?
View 9 Replies
Reverse lights not coming on, and parking sensor stuck at ' OFF ' , have replaced switch to no avail
Any tips out there ?
2005 6.0 Supercab Lariat diesel Auto 4 wd
View 1 Replies
Would it be a good idea to change the injector hold down bolts when I do the injector o-rings? They have never been out at 333,000 miles.
Plan on doing glow plugs, injector wiring, valve cover gasket's, intercooler pipes and the dreaded oil cooler.
View 14 Replies
I drive a new to me 2005 F350, he has a 2001 F350. While we were talking he said he didn't think his pickup had the power it should have. He pulls a 5th wheel camper that weighs around 8000 pounds fully loaded. He said it takes a couple of miles to get to 55 mph, and it is hard to hold the speed. It doesn't have the power it did when he first got it last year. He was told that a diesel is slow getting started. He rode with me in mine, when I dropped it about half throttle to pass a slow car he said he could tell mine had way more power.
His check engine light is not on, it starts good both when hot and when cold. It runs smooth, no miss as far as I can tell listening to it. What are some common issues that could cause this? He did just change the oil and fuel filters, not sure about the air filter. He said the power loss came before he serviced the engine, and did not improve after the fuel filter change. Where to start? He was also told to check the filter inside of his fuel tank, so he is getting ready to drop his tank.
View 14 Replies
Auto trans. The Overdrive light flashes on the Selector lever. Never stops. I put tape over it because it is annoying. Especially at night. It goes into overdrive no problem.
A Couple of times it did not flash and was stuck in first till I manually shifted. Then the light started flashing again and works normal. What now......RPM Sensor?
View 11 Replies
I am having trouble with my 1999 F350 Ford Powerstroke, Looses power but the motor never quits and also starts up fine, will set and run and warm up on the coldest morningIdles fine, It will hold back sometimes and not increase speed. I can take it out today and it may be fine and tomorrow can't run 2 miles. I was thinking CPS but after reading information I am not sure. What may be causing this issue. I just put a High Pressure oil pump on it could this have anything to do with it. Was not having a problem before the pump was changed. The pickup has 190,000 on it actual miles.
View 7 Replies
So I have the luk full ceramic clutch now, this is my second one (about every year it needs replaced) and it's getting close to needing a new clutch again. Right now my 7.3 is sitting at 442hp and 864 TQ. Im Building a forged rod motor with the idea of getting 5-550 HP to the wheels out of it and hitting the 1000 TQ mark. What clutch will hold that and not chatter and try to knock my teeth out like my current clutch. The closer to a stock clutch engagement feel the better, I hate backing up or starting out with a load more than 10k (I have to start in low, or 4wd low to backup). Truck is a 01 crew cab, on 35's stock gears may be going to a 6" and 37's in the future but that's it.
View 5 Replies
I have been reading here about alternate methods to torquing the hold down bolts for the injectors. This winter I replaced my old stock split shots with new alliant single shots. I installed the injectors into a cold engine and torqued the hold down bolts to 10 ft lbs. I did not ever go back and re-tighten.
Is it suggested to go in and re-tighten the injector hold down bolts to 10 ft-lbs after the engine has been heated up and cooled down? What are some symptoms of a loose injector? I am imagining premature wear on the injector cups, low compression and maybe some mixing of oil into the combustion chamber.
Did just throw the injectors in and go back later to retorque only to find they were all fine or were some loose?
View 14 Replies
I wanted to know what happens when the injector hold down bolts are not torqued down to spec, what problems would arise and could it be a reason for somewhat hard starting?
View 1 Replies
Parked truck, went to leave and truck starts and runs fine, says brake problem on message, wont let me move gear selector out of park, is there a way to do this manually and get it to neutral so it can be towed??
View 2 Replies
Seems like I have an issue every other week of driving my truck. Today I arrived at work and attempted to shift into park but it wouldn't go. I went to tighten the bolts and after tightening it still wouldn't work. So I tried tightening them again and the top of the top bolt broke off. So I took a nut and a lock washer and put it on the other side (was very hard) and got it tightened best I can. It looks tightened pretty good but I still can't shift into park. Maybe the bushing for that piece are bad? I have no clue where to go from here or what I need or even if putting a nut on the bolt works.
View 4 Replies
Won't shift into park, Checked the two bolts and they were tight. Ended up having a rock wedged behind shift lever on the transmission.
View 3 Replies
Isn't the park gear selector indicators suppose to me illuminated when you turn on the lights, mine aren't. Why?? stick shift between seats on floor.
View 5 Replies
My truck will not always start when in park, Have to switch it to neut sometime, and sometime after putting it in park it won't fully engage, I know the part that I need to replace just don't know the name or the part number for ford....It is the part that adjusts the shift indicator...
View 2 Replies
I have 2000 F-250 7.3L when I start it up and push the brake it won't come out of park and when I push the brake the volt meter goes to 8 volts. If I shut it off and try again it is ok. Might take a couple of times of doing this then it's ok for a couple of days then it happens again. I've checked the connection on brake switch and everything looks ok. What to check next?
View 1 Replies
Whenever I manually pull my gear selector into first gear it blows one of the 10a fuses (not sure which number). I lose all gauges and accelerator pedal. It's about the fourth fuse from the right on the bottom row.
View 4 Replies
My cousin has 1999 f-150 v8 automatic. Anytime you take it out of park you get forward gear. Was fine when parked just started happening on startup.
View 1 Replies
I have a 2002 f250 CC 4wd 7.3 and I have no power to my reverse light sockets. I am stumped, all my fuses are good, I don't think there's a relay so i haven't checked that. My neutral safety switch is good, I'm getting power to both the blue/pink and black/pink wire. What it could be, at first it was constantly blowing fuse 27 every time I put it in reverse but then it stopped blowing it obviously because they won't come on.
View 8 Replies
