It's happened to me the last 3 times I've taken my truck out and drove through some deep snow. I have a hard time shifting the transmission from drive to park. The snow must get packed up under the truck near the shift linkages.
View 14 RepliesWhat's the truth behind the deep pan automatic transmission pans? I hear they are supposed to carry a few extra quarts of transmission oil and result in lower transmission temps. I've also heard this is not true since the amount of fluid going through the transmission cooler over a period of time still remains the same and therefore will not provide any lower transmission temps.
View 14 RepliesI noticed my '99 started getting difficult to get in gear & shift, within a coupe of days the peddle was barely off the floor before it would engage. A day later it started 'creeping' if started while in gear. Replaced the master/slave cylinders with no change.
Is a clutch replacement the next step? Just thought I would ask before throwing money at it, since the only other times I've had clutch issues there was slipping or it just plain exploded.
I have an early 99 F250 4x4 7.3L..... 4R100....
Brief history, a while back on way home from work I let off of the accelerator and had a loud gear meshing like grinding noise, got back on the accelerator and went away, let off and back, so I quickly stopped and pulled over, went through the gears and reverse, everything seemed ok,??? went on my way, got home parked the truck and went about my evening. came out next day to leave and truck wouldn't move in reverse, forward but not reverse. long story short I was told that the snap ring internally probably came out, I have heard of this being a big issue with these, so I set up for it to be rebuilt, got it back and installed and still same issue, what the crap so I ended up having to pull it back out and amongst my own trouble shooting I found the simple issue and was the nylon riders on the 4hi/4low shifter fork were completely gone and allowing the planetary group to free float in and out of 4x4 neutral!!! NOW on to the issue at hand. so far only thing has been done is rebuilt and those fork riders replaced.
now I can move but 2-3 upshift under a load(more noticeable) has a delay going from 2nd to 3rd and under a load it hits hard. I talked to the guy that rebuilt it and he said that the rebuild kits don't always the right springs for the valve body and causes shift issues, so he talked me into the shift corrector kit which I researched and did see what he was saying, so had that done and still no better, still does it, however, it does shift into the gear softer but didn't fix the delay or the hitting hard when it did finally go into 3rd.
After being forced to drive it that way I have since determined that what it happening is it is coming out of 2nd with a second and half pause and then shifting into 3rd, the hard shift comes in to play because during the delay the torque convertor is locking up making it a direct drive like popping the clutch on a standard!!!
I just swapped out the sol pack and I heard from a youtube video that the bolt next to the 2-3 upshift valve on the valve body could be to tight and making a sticky valve, so I re-torqued all the bolts and nuts put all back together and test drive proved to be worse, I now have same issue in all upshifts. all hit hard now, I am at a loss and don't know where to go from here, I can only imaging the sol pack is causing this but I have yet put my org one back in to see... oh and I found two bolts on the accumulator stripped and found one non torqued bolt on the main valve body!!
This is the first winter for my truck, and the first time I've driven a truck in the winter. I struggled to get out of my street this morning, through 15" of unplowed heavy snow. As the traction control seems to engage, and even sometimes when it doesn't, the truck literally shakes very violently. I even had to lock the rear diff to get out this morning, but that didn't seem to make the shaking any worse. What causes the shaking? Is it just my truck? I've driven Land Rovers with full-time 4x4 for years, never any shaking even when they are spinning like crazy and traction control is operating. One thing I did learn that seemed to be a question of several on this forum...traction control does operate on the front wheels when 4x4 is engaged, in addition to the rears.
View 14 RepliesI bought it 4 years ago with 205K, swapped trans fluid.. 10k miles later (I don't drive it a lot ). I am throwing the code P0750 Shift A malfunction.. i figured id swap the solenoid pack since I am pretty handy and it was affordable.. but it didn't seem to do the trick.. it drove around the block good for 5 minutes before it started shifting weird and throwing a code again.. almost seems to be slipping... I still have to check fluid level again and scan the code again but any suggestions? I have an apt to go to the tranny shop this week and would like to avoid the big bucks if possible.
View 14 RepliesProblems with my 2001 F250 4r100 transmission. Transmission will only shift to 2nd gear when throttle is feathered at @2500 rpm. All other gears shift perfectly. This problem is consistent.
View 10 RepliesMy 1999 4X4 is allergic to snow! In the morning, after a blowing snow night, the transmission won't shift up. 15 miles or more in low, sometimes second, before it will find drive. Something gets wet! It only happens right around the freezing point. Maybe the Manual Lever Position Switch, or whatever it's called, on the side of the trans?
Also the throttle hangs up and it wants to race about 2000 RPM at the same temp. That could be ice in the throttle body. Shut it off for five minutes and it's OK, but it darn near put me into a snowplow yesterday when it wouldn't slow down.
Well I've been towing for almost 150,000 miles with a 2012 6.7 Lariat 4 wheel drive. Things have been going pretty well with the truck. I noticed some sluggish and indecisive type shifts early on but now I'm worried. I depend on this truck for pulling a horse trailer all over the country and Canada. Just recently I've been getting a hard shift or a thump or a clunk when shifting up or down in to second gear. I'm at about 152,000 miles and did a hot flush with LV ATF at about 148,000 miles. Should I worry or keep running?
I have a 97' PSD I'm thinking of giving a nice paint job and a flat bed but am reluctant to do so due to financial concerns and the fact that some folks may not want to see me pull up in an old truck no matter how nice it looks. My tranny temps have been stating under 200F and I really keep an eye on the temps when running up and down the hills while towing. The trailer is a 35' Gooseneck with a max GVRW or 14,000 pounds. Should I wait for the tranny to grenade and then drop in a built tranny and if so who's building these tranny's stronger than stock? Long time no see but this site has always been my go to for all my Ford truck questions, upgrades, etc.
I have a 4r100 on in a 99 7.3 4x4. The shifting problem I have appears to be intermittant. it seems loose after warm up especially at the 4th shift overdrive and passing gear. possibly due to low presures ? sometimes (lately more often than not) hunts back and forth between 4th and o.d when passing or hill climbing. Under normal driving it shifts somewhat firm with 4th being an exeption.I have changed my crank position sensor filters and fluids which had turned dark and improved slightly. When I pulled the pan and replaced the filter the pan was spotless. No residue or signs of plates or debris. There is about 100,000 miles on the tranny and 350,000 on the truck. Questions: Is there a tcm for this transmission and if so could it cause these problems? I'm considering a purchase of an unlocked 1705 superchip to change the shifting but unsure if this will work for my issues...
View 14 Replies2000 powerstroke 4r100 transmission. It has 155k just had it rebuilt and the shop is having a night as am I. It was shifting hard and the o/d off light would start flashing after you drove it a while. Its still doing the same thing and the shop checked the whole wiring harness and replaced the accumulator twice believing they got a bad re-manufactured one. The only code I can pull is a 605 pcm read only memory error. Could the cause be a bad pcm? The shop doesn't seem to have a clue at this point and I'm out 2500. IV taken it back twice now and Iv driven it a total of 35 miles since the rebuild...
View 1 RepliesBack in January I had my right front wheel bearing and u-joint go out, so I replaced them both. At the time I didn't realize my outer stub axle shaft was wore so I just put it back in. After a little driving the right side started to "thump" and "pop" when I would make hard left turns driving around town.
I replaced the outer front stub axle shaft and seal again because the old one was worn down. This eliminated any play in the u-joint. After a bit of driving the thumping and popping noise came back.
I decided to dig into it today so I pulled it all apart. When everything is apart it turns easily, no issue at all. When I assembled the wheel bearing, torqued it to 55 ft/lbs and installed and "locked" the hub I noticed something peculiar. I can barely turn the whole assembly by hand. I have to put a good amount of force to get the whole assembly to turn at all. When I walk to the driver side with all the same parts there i can turn the wheel bearing and locked axle shaft with one finger on the studs.
I have been in this thing 5 times and can not figure out what the heck is wrong. I can't figure out why this stupid axle shaft and wheel bearing are so hard to turn, together or separately, and I can't figure out how to get my front end to stop that thumping and popping.
I have been having an issue with my 4-5 gear shift under hard acceleration and know that a rebuild is due soon but I was wondering if any high performance kit available with all the clutches and friction discs needed to rebuild.
View 6 Replies03 6.0 with 90k miles. New heads, all orings , stand pipes, injectors , glow plugs, egr delete , oil cooler and studs . Has sct livewire. Just took the truck to the shop for a hard start issue and misfiring at around 30% throttle driving. It would fire up great in the mornings with some white/blue smoke till warm. But after it was warmed up you shut it off it would fire right back up but very slow to reach proper idle.
But if it set for about an hour it would crank great start but same lazy idle up but now it wouldn't get over 300 rpm before it would die. And do this for 5 or so more times before finally idling up. Then runs pretty good other than the misfire. So he said it's either the hpop ipr or icp. I had him replace all 3 with motorcraft parts. Still the same issue ! Return the truck to stock tune and it doesn't have any power . My pockets are only so deep...
I have an 04' R32 with about 56k on it. Here's the problem; when I drive it hard and speed shift from 2nd to 3rd it grinds just a little. It doesn't do it when I'm just cruisen grany shifting. For awhile now I've been thinking that the synchronous from 2nd to 3rd gear was going bad, till I talked to a friend with a 20th GTI who said that the 6 speed trannies will start to do that, and there's really nothing you can do about it. Is this true that I just have to deal with it or can it be fixed?
View 12 RepliesSeems like I have an issue every other week of driving my truck. Today I arrived at work and attempted to shift into park but it wouldn't go. I went to tighten the bolts and after tightening it still wouldn't work. So I tried tightening them again and the top of the top bolt broke off. So I took a nut and a lock washer and put it on the other side (was very hard) and got it tightened best I can. It looks tightened pretty good but I still can't shift into park. Maybe the bushing for that piece are bad? I have no clue where to go from here or what I need or even if putting a nut on the bolt works.
View 4 RepliesWon't shift into park, Checked the two bolts and they were tight. Ended up having a rock wedged behind shift lever on the transmission.
View 3 RepliesWe have a 2002 excursion. I have replaced the 4x4 selector switch on the dash as well as the front hubs they are now the warn premium hubs and the transfer case shift motor all part are ford all but the hubs. My question is it will not shift from 2 hi to 4 hi to 4 low, I have done all the right things that the book says to do, put vic in neutral keep foot on break, switch selector switch to 4x4 or 2 or low and it will not shift. When the transfer case shift motor was off i put the truck back in 2 wheel drive by hand with a wrench and it moves free no binding what else could it be the fuse under the steering wheel is good and new parts are good as well...
4x4 2002 excursion limited 7.3 only mod is cold air intake....
The truck: 03 Ranger, 2wd, 2.3L, 5spd, 160k mi
I bought the truck two years ago and it's always been difficult to shift (especially into 1st, 2nd, 3rd). I don't drive it often and only put 5k mi on it since I bought it.
The problem: Someone more mechanically inclined than I once told me that the hard shifting is probably due to the clutch not fully releasing due to low hydraulic pressure brought about by a failing slave cylinder.
I just noticed today that there is a high-pitched squeaking coming from somewhere on the truck. At first, I thought it was the rear end, but now, after pulling it into the driveway, I noticed that the squeaking noise vanishes when I push in the clutch pedal and returns after I release the clutch pedal and drive in 1st gear.
The transmission oil level is good, but I've never changed it and I'm not sure if the previous owner ever did either. I'm hoping I haven't damaged the transmission.
After reading a few threads, it seems the problem might be the input shaft bearing. To replace it, I'd need to drop the transmission and borrow a couple of tools I don't have (feeler gauge and bearing puller). If the ISB is the problem, it seems like it would be a good idea to change it now before it seizes and leaves me stranded somewhere.
Iam looking at a 2000 7.3 Powerstroke that has some problems first it is hard to start cranks like it has a dead cyl. Second after starting it has no power not even enough to move. At first it would only run if held wide open but once it warmed up it would idle and rev and move but barely still had a miss. The weird thing is it did not smoke blue-black or white also no strong smell of diesel and no smell of oil at all. The truck has 230ish miles and there are no maintenance records.air filter was new.
View 7 RepliesI've got an E99 powerstroke. Recently it's been getting hard to steer, if not impossible. When I'm parked i can't turn the wheel and it gets better if i Rev the engine up, driving is usually ok and going around corners. It's just low speed, low rpm that it won't.
Also every once in a while when braking it feels like i lose all power brakes. The pedal goes to the floor and the brakes let go, then i can feel the pedal pump back up and i get a good feeling brake pedal again that actually stops well. All this happens within about a seconds time. But the steering is by far the worst.
I just did the power steering flush with atf and it didn't work. I'm thinking i need a new power steering pump, but want to ask here first to make sure. The truck has 290,000 on it, and it never has been replaced to my knowledge. I bought the truck with 147,000 however so it may have been done before that.