The fuel line on the passenger side under the turbo that leads to the head is leaking looks like from rubbing on the pedestal, anyone ever just cut it and throw in some fuel line and hose clamps?
View 14 RepliesNew to me early 99 (4/98) f350 7.3 6 speed. Truck started acting up a few days after I bought it. Return line at fuel bowl was leaking, so started there and found a bad seal on the Fpr (unrelated to the fuel leak due to disentegrated compression sleeve). Fast forward through a bunch of parts swapping that still resulted in miserable lift pump pressure readings, I pull the sending unit out of the tank, expecting to find a plugged screen.
Well, there was in fact a plugged screen... Attached to the bottom of an in-tank pump. How did that get there?!? Everything I've read says there should only be a pickup tube??? Should I get a new sending unit from a junkyard and do the hutch mod or???
What are the hose lengths for the 2 HPOP and cylinder head oil crossover line? How about what size oring boss fittings you need into the head?
View 1 RepliesSo my understanding is that if your turbo is leaking oil, you either need to rebuild it or get a new turbo cause the one you have is shot.
I have some oil leaking, but it's not a ton. One one of my buddies was telling me that it's possible that the amount that is leaking is normal due to the PCV (Pressure Control Valve) system, or something like that. Here are a few shots of the turbo, as well as the boots that are leading up to the turbo.
I bought a 2003 F250 7.3 Powerstroke from a buddy of mine with 99,500 miles. It is a former Michigan truck and has some significant rust issues. Oil pan and drivers door will need to be replaced in the not too distant future. And probably bed rails later too.
In any case, I noticed a puddle of tranny fluid on the driveway when I got home today. The passenger side line at the fitting into the bottom of the radiator has corroded through. The fitting into the radiator is pretty rusty, and the line fitting is darn near destroyed. The line itself actually has a hole in it.
I see the same part numbers on different sites with different descriptions. Driver side here, passenger side there, inlet here, outlet there. For the same number.
As near as I can tell, Dorman number 624-059 is the outlet line from the tranny to the passenger side radiator fitting, and should be the part I need. Correct? Dorman 624-058 seems to be the line from the OTA auxiliary cooler and back to the tranny. What I cant find is the line from driver side radiator to the OTA cooler. That fitting is corroded bad too, and I may as well do both of them.
My HPOP was leaking so I pulled it our last weekend along with the fuel bowl and put all new seals in. All my previous leaks are sealed but now this stupid fuel bowl is being a major PIA.
The return line coming off the FPR will not stop leaking! It was slowly dripping when I first replaced the bowl and I thought the leak was between the fuel bowl and FPR housing. I ordered new rings and put it back together.... still leaking.
I wrapped a towel around the fuel fitting and realized that is were the leak is actually coming from. I went to the parker store today and got 3 new 60VL5 sleeves. The first one tore while sling over the fuel line (I was using 2cycle oil as lubricate). The second one leaked even worse.
In a desperate attempt to stop the leak, I slid the sleeve onto the fuel line as far back as it would go. I inserted the fuel line into the bowl and then put a thin coat of rtv on the exposed fuel line. I slid the sleeve over the rtv and then put a light coat of the outside of the sleeve. I tightened the nut up and am waiting for things to dry before trying again.
Why is this fitting giving me such a hard time? I've pulled the FPR housing and it is not cracked so I don't know what the deal is.
2005 PSD 6.0L Excursion ... I suspect that have a fuel leak at the fuel line fittings near the driver side cylinder head. (I believe that it is fuel, since it is so clear, I guess I should collect a few drops and see if it burns vs. coolant.)
It appears to be at the junction of the fuel lines. This is the point where the fluid drops off the tubing and falls down. The clip that holds the two tubes together at the joint is very dirty, the one below them is clean. The tag on the line that is at the joint leaking is part number 3c34-9j338-ag. Is there a o-ring in side the joint? Do I need to replace both hoses of the joint? I can't find any posting of a history of this fuel line leaking.
Or... is it that the joint never fail, and the leak is up tube? I can't see any where it is coming out when viewing it from the top.
Having trouble figuring out how to remove the rear fuel line from the fuel pump. Doesn't seem to be the type that uses the quick disconnect tool like the front line does.
View 5 RepliesCouple of years ago I installed a fuel pressure gauge. I wrapped the fittings with teflon tape. Well within about a year it started leaking. So I shopped around and used Permatex Permashield fuel resistant sealant on the fittings. It says diesel resistant on the package. Couple months later leaking again. So I take it apart again, clean every fitting and follow the instructions to the letter. Well its leaking again. What will resist diesel fuel under 55 psi pressure. All the fittings seem to be pipe thread.
View 7 RepliesI am rebuilding the oil cooler and noticed since its removed I have great access to this fuel line pair from fuel bowl to soft lines below. How these disconnect at the soft lines? I happen to have a new set waiting to be installed. Is there a tool required ?
View 3 RepliesIs this job worth doing as a preventative maintenance item? I replaced the rear fuel rail plug (aka banjo bolt) o-rings because they were very easy to get to with the up-pipes out. But the cylinder head plug in the rear is pretty high up and even with the up-pipes out, there isn't enough room to get a breaker in there that's long enough and has enough movement to loosen it. The front would be easier to get to, but both accessory brackets need to come off to get to them on both sides.
As far as I know, none of them leak but they're all 17 years old... BTW in case you haven't been following, I'm doing up-pipes, injectors, turbo, rebuilt HPOP & fuel bowl, boots & clamps, etc. so I'm trying to knock out any PM items while I have it apart.
2003 Excursion 7.3
There is fuel leaking from somewhere on the passenger side of the engine.
What things should I be looking for? I'm thinking injector? Is it easy to identify and replace?
I have a 2001 f250 7.3l 4x4 and the fuel filter housing is leaking real bad from either the back or under it. I need to get info on parts that i would need as well.
[URL]....
The ford dealer in Las Vegas replaced my turbo with a remanufactured one. Coming off the line (like quickly pulling into traffic) it goes flat on power until I get a few RPM's. Even with the old turbo it never did that and I drove it for the last 30k miles with it throwing the low turbo boost code. They put a little over 100 miles on it for road testing (I did have other things that they worked on. {4x4 2006 F250, 6.0 engine, 110k miles and I bought it new}....
View 4 RepliesEver since i bought my truck i have had a bad power steering whine. Replaced the pump and its still there. I got the truck in 2006 and think i replaced the pump in 08 maybe. Anyway I've purged, bleed, changed the fluid. Pulled a vacuum on it and still no luck. So I've just dealt with it for 11 years.
Well i can remember reading something somewhere about ford up-dating or redesigning one of the power steering lines that was causing this noise.
My father inlaw just bought a 02 and its so pleasant not to hear that when riding in his truck. It made me want to investigate the matter. SO if its as simple as a updated line I'm buying one asap. He got rid of his Chevy because of the reliability I've gotten out of mine.
Well I am at a loss now. Rebuilt the turbo with a new wheel and kit from Riffraff. I still have no power, no boost and no codes. The new wheel whistles. I can hear it. It sounds way better than the old one. But still no power. I really don't know what to do now.
View 14 RepliesI just replaced my 3rd HP power steering line last night( 3rd in 300K, always blows the same point....fitting comes apart where it attaches to the pump.
I'll start, mine have gone about 100K plus or minus 10K, almost thinking about making it a 100K maintenance item.
2003 XL 5.3L with a leaking fuel line between the tank and filter. Mechanic says that this line is only available in a kit that includes all fuel lines for the truck. Hard to believe you can't just get the one line.
View 4 RepliesAs I was getting ready to leave town with the tractor loaded up, I was accelerating with the turbo spooling up when I heard a bit of a pop and lost power (engine still running and all, just very low power like you get when the turbo fails). I wasn't far from the shop so I came back and started getting a lot of white smoke out of the exhaust, it doesn't smell like diesel, probably more like oil. Definitely smoke, not coolant. I pulled it around back and shut it down to go grab AE and scan it and it shows a P0475, starting it back up has light smoke at idle and it idles fine but as soon as you give it any throttle it starts smoking pretty badly.
Researching it looks like the most likely cause for this is the EBPV itself but before tearing it down that far. This is the only code it's showing.
Truck has 272k on it, turbo was rebuilt a couple of years ago but we didn't do anything with the pedestal at that time. I guess in retrospect, I probably should have done the EBPV delete and the resistor fix then but I didn't think about it at the time.
On another note, my AE is not showing any of the system test for some reason, the drop down is blank. I have version 7.0.1, so it's an old version but I'm working on an old truck, so... What that might be? I've got the truck pulled into the shop now to let it cool down. I'll probably let it sit overnight and take the turbo and EBPV out tomorrow unless someone has a better suggestion...
While my turbo is out I decided to delete the EBPV. I removed the butterfly and rod, & pounded in some 3/4 inch freeze plugs. Are there any mods that need to be done to the pedestal, or can I just leave it the EBPV plunger unhooked? It's not leaking, but will it leak if left unhooked? Or do I have to gut it and tig weld the oil gallery's
View 14 RepliesDropped her off at the dealer for the 30k service and minor oil leak near the turbo.
-Water pump replaced (never did whine nor did I notice it leaking)
-Valve cover gasket replaced
-Oil inlet line on turbo leaking
-Wastegate clamp
-Driver side window regulator
Already had my intake mani replaced around 25k miles. Hopefully this will cover all the known/dreaded Mk6 issues. My 1.8T was bulletproof.