I'm checking my fuel filter regular (draining, examining.....basically OCD **** stuff) and I'm spilling diesel around the bowl. I've learned to put a rag around it now, but what's best way of cleaning diesel around that area? I'm tired of my wife complaining about smell. Simple green, purple power, etc???? Also, tell me what to watch out for.
View 14 Repliesjust bought this truck and it has a brittle cap and i cant get the cap to turn, its been on there awhile . 99 f250, anyway might have to destroy this cap to be able to remove it. Doing this without damaging the filter housing?
View 14 RepliesMy fuel filter lid o-ring keeps blowing out upon hot start, this has happened 4 times now once last week, I replaced filter and all was ok until Thursday it happens again I change the filter allis fine! Now today!!!!! TWICE I have to install new filters because the o-rings are blowing outside the bowl lid! I'm using the same BALDWIN PF7698 filters I've used for years, my reg. Is set at 75psi and holds steady! No spikes but I haven't been able to watch it when the o-ring blows out! Injectors and o-rings are new (<1000miles) no problems during operation at all!
View 14 RepliesShut my truck off for about 15 minutes and wouldn't start back up. Installed new fuel filter. And gonna try changing cps. Torque says Rpm 180
Ipw. Bouncing between 600 - 3000 Hpop. 250 while cranking Voltage 10.9 while cranking. Ipr starts about 15% and slowly climbs to about 88%
Fuel pressure about 65%
Tried unplugging cps. Gonna check oil now though I check it every time I fill up and it never uses any.
I am attempting to change my fuel filter - have a new Napa unit complete with new lid.
I can not get the old one off (this alone tells me it's been on there too long). The hex is 26mm and all I have is a 26mm box end. It just rounds the corners of the plastic hex off.
As the new filter has a new lid, I am using a steel chisel and hammer (in a CCW direction) at several places on the top flange. I have also smacked the top flange liberally to get it to let go of whatever is holding it.
I'm about to get out my map torch out and warm up the plastic but would rather not produce a flame on something with fuel directly behind it.
I have a 2001 f250 7.3l 4x4 and the fuel filter housing is leaking real bad from either the back or under it. I need to get info on parts that i would need as well.
[URL]....
I'm in the process of replacing my HPOP lines and fittings and after I got everything removed and started cleaning the threads before re-assembly I noticed this green wire (located above the fuel filter assembly) that apparently I pulled out of its socket.
What is it for? Can I just push it back in its sleeve right below the red wire??
I just changed the drain valve on the fuel filter bowl. All went well and no more leak, but now I am getting an "emission system" warning light.
After I replaced the valve, I filled the fuel bowl with diesel fuel. Was there any other priming that needed to be done (if any)? What the emission system warning light may mean?
2002 F250 7.3L 4x4.
We have had our Ford 6.7 diesel for a week today and on the way home I am pretty sure it did a regen. It flashed up and said "clean exhaust filter, then the miles per gallon dropped to down around 11 from 15.5 rather quick. The truck smelled really hot and we drove it for about 35 miles to home and MPG started going up and now it's ok. The thing that stumped me was that the truck only has 620 miles on it vs 6.7 miles it had when we bought it last weekend.
View 11 RepliesI've been having frequent, low speed, short trips lately and have been seeing the 'Cleaning Exhaust Filter' message pop up. Given that I have only been mere minutes from my destination in each case, I thought 'good luck with that'.
Today I see the 'Drive to Clean' message, followed by the 'Cleaning Exhaust Filter' message which stayed on (I have been used to it appearing for only a second or two.)
It should all be fine tomorrow though as I have a longer trip planned.
I have a 94 F250 5.8 liter with 96K miles. Can I remove the fuel rail and clean or replace the filter that is placed at the top of the fuel injector?
View 10 RepliesI am at 34,600 miles and had the oil changed yesterday afternoon. My son picked the truck up for me and on his way home the "drive to clean exhaust message" came on with the "check engine light" at the same time. I get home from work, re-check owners manual and no mention of the check engine light coming on with the drive to clean message.
I called my service rep and he says drive it as per owners manual, so I head out drive about 45 miles, averaging 60 mph nothing changes, both lights/messages are still on. Truck seems to be running fine and the last cleaning exhaust message was Sunday and I believe I was out long enough for it to do its job. It will go into the shop tomorrow, but was looking for thoughts from the the rest of you pros before I go.
I mention the oil change only because after the last oil change at around 30,000 miles I drive to work 2 days after and my water pump starts leaking.. coincidence I know.. but getting freaked out as I approach 36000 miles..Truck is a 2011 and I bought it new in Jan of 11.
doing injectors and pulled the valve cover, and noticed its not as clean as i expected. in the oil on top of injectors i noticed its got some grit in it. this cant be good and not sure how this debris got in there as i always change oil and air filter regularly( unless previous owner neglected). is there a safe way to clean this? Is this a normal find for you guys that have done injectors?
View 1 RepliesChanged fuel filters today. Now my water in fuel light is coming on. But the truck is not running any different no sputtering or anything. ????? Could this be human error
View 14 RepliesHow can I tell if my truck has a cabin filter and where would it be located? I looked through the OM but it was little to no luck....
View 3 RepliesI have a very slow fuel drip off the housing for the fuel filter on the engine. Can't see where it's coming from. It started sometime after I changed the filter a couple of months ago.
View 5 RepliesDumb question but how do I remove the air filter intake from the turbo Its a little oily there from a fuel or oil leak but I dont see a clamp holding it on the turbo?
Also what is the e clip? Is it the little thing holding the wastegate rod on the exhaust turbine? Can I just pull the rod up off the clip?
my first diesel, and second 2002 f250. I picked up my 7.3 4x4 automatic CCSB last week. 202k on the odometer. I need to change the air filter but idk what to use. I don't think it's stock. The side of the air box says aFe. What the part number for the filter is? I don't see one on the filter anywhere.
View 6 Replies2000 F350 with 340000 on it, have had it for the last 140000. It's an old service truck from south west gas with one owner in between them and me and he put about 5000 on it. I have the big cylinder open air filter, billet compressor wheel, 4" exhaust all the way and an Edge tuner. Don't have any codes I can pull with the tuner. Have been good to me so fare only need regular maintenance, but always had smoke out oil filler with a little pulse.
2500 ago I changed oil and add 1/4 of Lucas oil. 3 days ago when I started in the morning it smoked white smoke out the exhaust as a steam train and idle rough, but cleared up as I went down the street and will do so every time I start cold or warm. Ok, might need new GP, did that yesterday yet the same. Now I start checking stuff and have smoke out the oil filler as a steam train so the cap won't stay.
I know it sound like alot of problems, just try to verify some of them. The smoke out oil filler is blow by? The smoke on start up is that related to bad injectors? Can a bad injector dumping fuel create the blow by? Coolant level ok Transmission fluid level ok Engine oil Rotella T6 added 3 quarter in 2500 miles. I do not have a scanner or any other advance test tools.
I own a 2003 E450 (transit bus conversion) with a 7.3L w/ California emissions. I recently noticed I have a considerable amount of oil in my air intake going back all the way to my turbo starting where the crankcase breather tube attached to the air tube. The breather seems to have some sort of filter housing that is attached to the top of the valve cover. I removed it and it appears to be fairly heavy as in if it's a filter, perhaps it's full. If I'm getting oil into my air intake from where the breather tube comes off that housing and joins in my air tube back to the turbo, could that filter or housing have gone bad? It appears to be a dealer stock item only for 225. I've saw on the web people posting "reroute kits" for the 6.0L but nothing for the 7.3. Does this part simply need replaced or could I be facing a separate issue as to why I'm getting oil in my air tube?
View 14 RepliesIPR CF2 Byasss High Flow Coolant Filter Ford 6.0
Made for the 6.0, the biggest problem on the 7.3 might be finding real estate for the filter assembly.
One review refers to using it on a 7.3.