Ford 7.3L Power Stroke (1999-2003) :: Front Wheel Making Screeching Noise - Lost All Steering?
Aug 28, 2016
Ok, so I leave the fire station this morning headed home and my steering felt weird. About 1/2 mile from home I hit a bump and my drivers side front wheel started making a screeching noise. I stopped and looked out the window and it appeared fine. I limped home and as I pull in the driveway, I lost all my steering. I look under the truck and this is what I found.
Not sure what to do. This is my daily driver and neither of my 2 mechanic friends will answer their phones.
View 14 Replies
Advertisement
So I have a 1999.5 F350 diesel and the fuse panel under the steering wheel is acting up. I was driving my truck home the other night and I lost power and my truck shut off. I have had a problem in the past with the #30- 30 amp fuse ( controls the PCM and glow plugs from my understanding) that is under the steering wheel, I replaced the fuse and everything started working normally again. Until the other night when my truck shut off, so I replaced the fuse the truck drove again for 20 feet died again, I was able to hold the #30 fuse and allow my truck to start up again but would eventually killed the PCM and shut off again and would not start up due to what I believe the fuse location shorting it out and killing the power to the PCM preventing me from starting it up again.
I had my truck towed home and charged the battery and it started up fine the next morning. If I push on the #30 fuse my truck the shorts out and kills the power, I do not know if this is normal? The fuse is sitting loose in the fuse holder is there anyway making it fit tighter to prevent it from being so loose? I have read every other post online about the problems and tried everything they have recommended but still can not figure out what was wrong with my truck. I disconnected the fuel filter heater, and also the wastegate solenoid to see if that would prevent the truck from shorting out if I pushed the fuse it did not work.
What the problem could be causing the #30 - 30 amp fuse to be shorting out preventing everything from working? Or how to test the fuse panel and all the relays?
View 5 Replies
97 F150 4x4 around 200k miles on it, Drove the truck to town today and it started making a screeching noise when I turn the wheel and moving at slow speed's It is not the typical Ball joint squeak, and they were replaced about 6 months ago. I also get a clicking squeak going down the road, everyone in a while from take of ill get a slide grinding or crunching noise. Also noticed that when taking a curve to the right i feel and hear a slight Bump but I don't when turning to the left/
Also it doesn't have the typical grinding noise of a bad unit bearing, there is a slight roar but Pretty sure that it is just the aggressive tire's... I am about to go out and Jack it up and have a look at it to see what it was. Also if I loosen the Cv nut on at the Hub that would show me if there was any play in the bearing correct? since the cv should keep the bearing's fairly tight even if they are worn?
View 3 Replies
I lost a hose in the driver side front wheel well this morning while pulling RV to a campground. By the time I got there and got the RV disconnected, I lost all power steering. I reconnected the hose using a zip tie and have a friend bringing me fluid to refill reservoir.
Is my pump toast now? Can I refill the reservoir and prime the lines and be good to go?
View 14 Replies
Driving home from movies tonight, I lost power steering and power brakes and the pump started growling. Looked in the reservoir and it was all foamed up. Within the last 20k mi I have flushed the system and refilled with power steering fluid. No apparent leaks at this time. And happened like someone flipped a switch. Fine one turn, nothing the next. What are the chances this is a fluid issue and not a mechanical one? Start with flushing system and adding Mercon V? Or is it likely pump is damaged?
View 7 Replies
I have developed a sounds that sounds like metal on metal. Not a grinding but more of a "swish swish swish" light metal rubbing when the truck has been running a mile or two. I can barely hear it over the radio but its very noticeable when the window is down. It is not affected by the pressing the brakes and it gets louder and faster in direct portion to speed. It will occasionally leave and start right back up. I touched the front rim around the hub and it was hotter than I wanted to hold onto. It didn't burn but it was hot. It was 105 degrees that day. Here is what I have done.
I replaced that front hub in 2010 and probably have 50K miles on it. I did the 3-9 test and there was no noticeable play. I spun the hub and while it seems to spin ok it does seem a little dry.... I will pull it tomorrow and see what it looks like.
I pulled the calipers off and the brakes pads are at half way and there is no burnt smell. I spun the rotor and it seemed flat and straight. I do have a small tiny lip all the way around them on both sides but I figured that's normal with 265K. I pulled the pins and they were dry but they didn't seem to be sticking. I cleaned them up with the boots and am going to replace them when I get some brake grease tomorrow. I have not looked real hard at the caliper but I plan on pressing that with a C-Clamp tomorrow to check it. Since the rotors and pads looked OK, I assumed there was not a stuck caliper although haven't ruled it out. The axle behind the hub seem to spin freely before I removed all this stuff and the hubs are not locked.
I think I covered it all .. I also thought it could be a rock or stick but nothing came out of my caliper or rotor when I took them off ..
View 14 Replies
Was making a U-turn, and out of no where, had no brakes and no steering.. Not a fun situation to be in....
View 14 Replies
I can take one finger and spin my steering wheel full left and right. There is no Resistance at all. Very scary to drive. Would it be the steering box. I am supposed to be at a military school tomorrow need to fix asap.
View 4 Replies
Initially had indications of a leak under the wheel arch on the drivers side.
About 3-4 months back replaced both PS lines and the leak stopped - briefly (maybe a couple a weeks).
Now the leak is back, but what's interesting is I lose more ATF fluid on a single long haul run than I do running round town for 3 weeks. I can't work out where the leak is coming from to identify what else to replace - short of just buying a pump and reservoir and replacing them as I've already done the hoses.
My turbo cooler pipe was hard up against the old PS pipe where it entered the side of the reservoir until I did the replacement hoses. Now I have it out the way but I'm wondering if it's caused some unseen wear or damage.
If I just do the pump to see if that works are the reman units any good out of Autozone or O'reilly's?
View 9 Replies
Having searched I believe that I need to remove two torx screws from the back of the wheel to remove the air bag. These have that damned protrusion in the middle so I'll have to find and buy a torx driver just for that job. What size is it?
View 5 Replies
Just bought a 1999 F250 7.3 cab and a half standard 266k miles. The steering wheel is really loose. Not loose as in turning the wheel to turn the tires but like moment up and down and side to side. Are there bearings to replace?
View 4 Replies
I think my pcm has gone bad. My wait to start light won't come on an when I turn my key on I can't hear my fuel pump cut on anymore. My vacuum pump is also making a loud noise.
View 10 Replies
I have a 2002 f250 7.3 and the belt is rubbing front edge of the belt and making a whipping sound at 65 mph. Have replaced tensioner, idler, water pump and a/c bearing & pulley.
View 2 Replies
Steering wise, it seems very likely that I'm due for a steering box. Lots of slop when I turned the wheels back and forth. Also, as per the seller, it seems like the the wheel bearings and ball joints are in good shape.
The sway bar end link bushings are smoked, so those need replacing. As for oil leaks. I'm thinking it would be best to pull the motor. It looks like this engine has had the pan off, but I do believe I have a front pain leak. The crank case breather is going into the intake which is annoying. And I believe the intercooler is full of oil, explaining the mystery oil leak by the passenger side intercooler boot.
Couldn't see any oil in the valley of the motor but I see oil coming down the down pipe of the exhaust, out the bell housing of the motor and dripping from a weep hole maybe 8 inches down the transmission as well? Seeing as to how I'm not sure what clutch I have, it make sense to pull the trans. And If I have the dreaded oil pan leak and a intercooler full of oil, why not just pull the motor? I'd also like to trim out the front panel for 05+ head lights and clean up the wiring on this thing. Found a cheesy electric compressor for a small horn. Sounds like a clown horn, no kidding.
View 8 Replies
Just recently i have noticed my truck acting up. the other day at about 10 to 20 mph i made a 90 degree turn and noticed my steering wheel wouldn't return but i had to bring it back. than this morning the same thing happened. I made a 90 degree left hand turn and it happened again. the truck wanted to keep going left but i kept turning right. it almost feels like my power steering pump is going out. The pump was changed about 4 years 90k miles ago. I'm curious to see what others have to say. What could it be????
View 14 Replies
Yesterday coming home from Morgan Hill I noticed my injectors making a odd sound on all the down hills while coasting - IPR % would drop between 9.8-9% making it almost sound as if the motor was about to complete shut down, RPM range was 500 -800 rpm, ICP 450-550 but the motor almost had a sputter to it... no codes, lights and it didn't run weak or have a lack of power but I've never noticed it before ...
ICP is only a couple years old
IPR is about 1.5 old
Both replaced with OEM parts .. Is this normal - or do I need to start digging somewhere?
View 3 Replies
My pickup has 316,000 miles on it. It's a 2000 ford f250 7.3 powerstroke. I have always bragged how my truck can pull anything because it has alot of power. Yesterday when pulling a 28' travel trailer up an incline I noticed I didn't have much power and it steadily got worse. Now I'm at a crawl when I hear a noise sounding like it lost air compression for a few minutes then the noise stopped. I stopped and looked to make sure everything under the hood was still attached and everything seemed fine.
I got back in and continued very slowly a few more miles home. Gauge were all good, never got hot. I put a scanner on it and it threw two codes. P1247 and P1248. I haven't noticed any unusual smoke. This is my second ford I've owned and know that when weather gets cold you may have to plug it in. But this truck it doesn't matter if it's 100 outside it will not start without plugging in for at least 1 hour. I've replaced all glow plugs hasn't worked. So I am assuming this break down now has something to do with it. I really am starting to not like fords!
View 13 Replies
2001 F350 XL... Fitting on PS pump broke and I lost PS and PB with fluid everywhere. Replaced the hose with a new one from Autozone and I have no noticeable leaks.
I know I lost more than a quart but I could only add less than a quart (Mobil 1 Synthetic ATF). I'm also getting a whine from the steering wheel when I turn stop to stop. The power steering is back and there are no leaks (that I see) but the brake pedal is mushy. I've pumped and turned stop to stop for a while. Do I have to bleed the system like I'm doing a fluid flush? I hate to waste the synthetic fluid that I changed about two years ago.
View 7 Replies
The steering on my truck has become a little heavy after making a turn and bringing the steering wheel back to center. The steering feels heavy like I had a front tire half way down. There's a lot of drag then once on center it's gone. Could it be the beginning of the end for my ball joints?
View 10 Replies
So I have a 1999 F350 diesel and the fuse panel under the steering wheel is acting up. I was driving my truck home the other night and I lost power and my truck shut off. I have had a problem in the past with the #30- 30 amp fuse ( controls the PCM and glow plugs from my understanding) that is under the steering wheel, I replaced the fuse and everything started working normally again.
Until the other night when my truck shut off, so I replaced the fuse the truck drove again for 20 feet died again, I was able to hold the #30 fuse and allow my truck to start up again but would eventually killed the PCM and shut off again and would not start up due to what I believe the fuse location shorting it out and killing the power to the PCM preventing me from starting it up again. I had my truck towed home and charged the battery and it started up fine the next morning. If I push on the #30 fuse my truck the shorts out and kills the power, I do not know if this is normal?
The fuse is sitting loose in the fuse holder is there anyway making it fit tighter to prevent it from being so loose? I have read every other post online about the problems and tried everything they have recommended but still can not figure out what was wrong with my truck. I disconnected the fuel filter heater, and also the wastegate solenoid to see if that would prevent the truck from shorting out if I pushed the fuse it did not work.
What the problem could be causing the #30 - 30 amp fuse to be shorting out preventing everything from working? Or how to test the fuse panel and all the relays?
View 2 Replies
I have some whine coming from my front wheel bearings so I'm going to replace them both. I'm not sure if this had been done on my truck before, but I'm thinking so since I have Moog greaseable ball joints.
Truck has 250k miles on it. I'm going to check the pads, rotors and slide pins. Anything else that might need work? I'm sure the half shaft could use a once over, but I don't keep my hubs locked so they don't turn much in regular driving.
View 7 Replies
