Ford 7.3L Power Stroke (1999-2003) :: Front Tires Started Rubbing
Aug 24, 2015
About two weeks ago my front tires started rubbing. I've been running the same size tires as long as I've owned this truck, and the PO ran the same size too. The rub is more noticeable when turning up an incline, but I've heard/felt the run on flat ground too. What would cause this "out of the blue"? Are my springs wearing out? FYI...I replaced the shocks less than a year ago, and bought the tires in March.
View 7 Replies
Advertisement
I have been "fighting" a front tire cupping problem on my L99 F350 Dually 2wd since I have owned it.
I got LOTS of paperwork with it, one of which was a service ticket from the dealer where it was bought new (with VERY low miles on it) saying several passing motorists had informed them that the front tires were bouncing down the road.
I have read this service complaint several times and I now feel that has something to do with it. I bought the truck with 70k on it some 8 years ago-the PO had installed EXPENSIVE Michelin XPS Rib steering tires on it and they were already destroyed by cupping.
I replaced all 4 shocks, and all 6 tires, begged the folks to FIND something wrong/loose/worn out on the front suspension/steering and they found nothing, they aligned it. THAT set of Cooper Discoverer HT tires did exactly the same thing, except I spent a lot of $$ having the tires rotated.
Now I have a set of Firestone TransForce tires on it and its been to a HD truck shop where I begged them to rip into the front end and FIND something wrong-THEY DIDN'T. THEY installed camber bolts and aligned it, yep, you guessed it STILL CUPPING!!
So, now I'm thinking is it possible that the wrong coil springs were installed at the factory causing this bouncing that the original owner reported to the dealer? I have now destroyed 2 more tires and getting tired of it.
View 9 Replies
I have developed a sounds that sounds like metal on metal. Not a grinding but more of a "swish swish swish" light metal rubbing when the truck has been running a mile or two. I can barely hear it over the radio but its very noticeable when the window is down. It is not affected by the pressing the brakes and it gets louder and faster in direct portion to speed. It will occasionally leave and start right back up. I touched the front rim around the hub and it was hotter than I wanted to hold onto. It didn't burn but it was hot. It was 105 degrees that day. Here is what I have done.
I replaced that front hub in 2010 and probably have 50K miles on it. I did the 3-9 test and there was no noticeable play. I spun the hub and while it seems to spin ok it does seem a little dry.... I will pull it tomorrow and see what it looks like.
I pulled the calipers off and the brakes pads are at half way and there is no burnt smell. I spun the rotor and it seemed flat and straight. I do have a small tiny lip all the way around them on both sides but I figured that's normal with 265K. I pulled the pins and they were dry but they didn't seem to be sticking. I cleaned them up with the boots and am going to replace them when I get some brake grease tomorrow. I have not looked real hard at the caliper but I plan on pressing that with a C-Clamp tomorrow to check it. Since the rotors and pads looked OK, I assumed there was not a stuck caliper although haven't ruled it out. The axle behind the hub seem to spin freely before I removed all this stuff and the hubs are not locked.
I think I covered it all .. I also thought it could be a rock or stick but nothing came out of my caliper or rotor when I took them off ..
View 14 Replies
I got an 03 f250 with a 10 inch lift on 40x14.50 tires on 20x10 fuel hostage wheels. They rub my springs pretty bad when trying to make even the slightest kind of tight turn and the sound they make when they rub is even worse than them actually rubbing. My question is should i stay with this tire and wheel setup and try to get some 6061 billet aluminum 2 inch spacers? (I'm not sure about going that route though because of what i heard about spacers) or go down to some 38s with a 20x14 wheel that hopefully would push the tire away from the hub like spacers would do. I'm leaning more towards going to 38s because of the rubbing and also because I feel they might look better on the 10 inch lift rather than the 40s but dont know whats the best thing to do.
View 12 Replies
I have a 2002 f250 7.3 and the belt is rubbing front edge of the belt and making a whipping sound at 65 mph. Have replaced tensioner, idler, water pump and a/c bearing & pulley.
View 2 Replies
I was out with the F350, drw, automatic, 7.3, 4 x 4, yesterday about 30 miles from home base. The transmission started pumping fluid out the front like I have never seen before. I am not talking a drip, I am talking a stream, a big one..... almost like pouring coffee from a coffee pot. I noticed it when I was backing into unload and was leaving an oil trail, a quite obvious one.
We took off the tc cover as it was coming off that to find a dry tc and flywheel, but fluid running out off the case. This is the second time this trans left me high and dry in 165k miles. The first time was a stripped tc/ input shaft. We repaired the transmission then but I don't think we replaced much besides being sure no debris went though everything, fixed what was broken. That was about 25,000 miles ago.
View 8 Replies
I have a 2001 F350 7.3 with a 6" lift..I have a extended pitman arm for the lift and I have just noticed that it is rubbing when I do a left turn....
View 3 Replies
I have a 2000 F250 super cab and the doors rattle going over bumps. I've seen the weather stripping mod and intend to do this but my drivers side doors are touching at the top. Would this indicate that the busings are shot? With the doors open, when I lift on the outer edge there is no movement in the hinge area. The drives door and drivers side back door actually touch and rub at the top. Any pointers?
View 10 Replies
So changing the oil in my truck the other day, I noticed the exhaust clamp at the union between my down pipe and first section of my exhaust has been rubbing the trans cooler line and there's a Nick in the granny pan. Lookin at the rubber grommet on the hanger, its stretched tight and looks like the exhaust has shifted over. What could have done this or possible fixes?right by now it's got a gob of high temp silicone acting as a stand off. Don't wanna put the new line in until I have the situation remedied.
View 10 Replies
I want to put 305-75-20 on my stock f250 4x4 will they work?
View 1 Replies
The issue: when I reach 37-40mph I have a new sound which I believe is the transmission 4R100. It sounds like a flat spot on a tire, or the sound tires make when they leave the sticker on them. The cadence of the sound is slower than the rotation of the wheels.
If I let off the accelerator, the sound stops, as soon as I add load by pressing the accelerator the sound returns. If I shift to Neutral the sound is gone.
If I coast at any speed the sound is gone. It is only audible when under load at speeds above 37-40 mph. The cadence does increase as I speed up, but it doesn't sound as fast as the motor is turning (~1900 rpm's).
I monitor the truck with torque pro using the PIDs defined here on FTE. I can see lock-up in 3rd and the shift to overdrive. When in lock-up, I see 1-7rpm TCSlip.
Watching transmission temp as reported by torque, the hottest I see is 183* pulling an enclosed 6x12 @ 75 mph. Ambient temp is 95*. Excursion currently has 240k miles on the clock.
This sound was first heard by my wife two weeks ago. I thought I had tire issues and they needed to be rotated. The sound is still present, and now identified only when the truck is in drive, and under load, regardless of me pulling a trailer.
Yesterday on my 500 mile trip, the truck hiccuped several times which I believe was around the time I was either moving in or out of overdrive. Details in a different thread: [URL] .....
Anyway, I've looked at all culprits and can't find anything with the motor, or electrical system. I can't get to a transmission shop until Monday, and won't have my AE until I get home Sunday night. I have a 500 mile run tomorrow. I checked the transmission fluid and it's at a good level, pink, and doesn't have a bad smell.
View 14 Replies
My transfer case engages the front drive shaft spins but even when I manually lock my hubs neither of my tires will pull! I was thinking either the hubs are shot but I was told it could be the 4wd locking solenoid??
View 1 Replies
Thought batteries were bad and replaced batteries truck started and ran. Shut it off and went to restart 30 minutes later and had no power what so ever like no batteries were in it. Put new batteries on charger the were full so hooked batteries back up and it starts. 10 minutes later same as before like there was no batteries in it. 2001 7.3 464,000 miles
View 4 Replies
I was driving my truck then all sudden truck started losing power then slowly died. I restarted it, it was a lil shacky then died again. Iunscrewed the fuel filter and looked in the housing and there was lil fuel in bowl i turned the key to on position and bowl did not fill with fuel looked as if it were shooting some bubbles up(air) could it be outta of fuel???
View 10 Replies
A few weeks ago I replaced my CPS on the 99 7.3. Today was the first day I drove my truck in the rain. When I turned my wipers on, I noticed that I lost power and my truck started hiccuping. I read on these forums that an aftermarket CPS is most likely the problem, so I am planning on getting a ford CPS this afternoon. My biggest concern is that before I replaced my CPS, my wipers only had 2 speeds. Also, if I pressed the end of the blinker switch to squirt the cleaner the wipers would not turn off until I turned the truck off. I am not sure why this would be happening and I wanted to ask if there is more than just the CPS involved with this.
View 7 Replies
Driving home from movies tonight, I lost power steering and power brakes and the pump started growling. Looked in the reservoir and it was all foamed up. Within the last 20k mi I have flushed the system and refilled with power steering fluid. No apparent leaks at this time. And happened like someone flipped a switch. Fine one turn, nothing the next. What are the chances this is a fluid issue and not a mechanical one? Start with flushing system and adding Mercon V? Or is it likely pump is damaged?
View 7 Replies
Well about 4 days after my HPOP replacement, the ol Ford is at it again. Apparently, one of my power steering lines has been rubbing on the top of my driver side front shock mount. It let loose in a giant black plume of black smoke and grinding gears as I was pulling into the corner store. Limped her home and inspected it. From what I see, its not a terribly expensive hose and shouldn't be too terrible to replace. One thing after the other [URL] .....
View 3 Replies
While headed back to town my 2000 f350 7.3 with 444,650 miles (I'm original owner) and have performed maintenance and repairs since mile 3. Truck started to loose power and eventually stalled, was able to restart several times to limp home 7 miles in one hell of a snow storm. Very confused, replaced cam position sensor ( keep one in jockey box ) replaced fuel filter truck starts then stalls out. Don't know if a bad HPOP would allow start up at all. Fuel pump???
View 6 Replies
So my OD light started blinking on the way to work today. The fact that my truck dropped out of cruise control and then started downshifting out of OD on the freeway and back into OD started this ordeal. A quick scan of the dash made it easy to notice the OD light strobe, especially in the dark.
I've read some posts in the past in the event it happened to me since my truck is far from new. I had it in the back of my mind that I would attack the VSS sensor with some contact cleaner then replace if that didn't fix the problem. Doing a search revealed a far greater spectrum of culprits. In addition to the VSS potential I have read about transmission handles, chafed wiring in the steering column, and even the transmission itself. Instead of re-inventing the wheel I'm looking for those that have more knowledge on this issue than I do. Here are my symptoms:
1. Drove 5 miles from my house to the freeway with no issues.
2. Shortly after getting on the freeway I set my cruise control at 65mph.
3. Shortly after that my cruise control 'dropped out' and the truck started to slow down (obviously).
4. When I got back up to speed the cruise would not work which is when the out of OD and right back into OD started. It did that all the way to work (it would go out of OD and back in every couple of minutes or so).
5. Transmission hunted on surface streets too (25mph).
6. Turned the truck off, waited a couple of minutes, then started it back up. OD light is off and truck drives fine.
A couple of things to note. This is the first time anything like this has ever happened with the truck. Also, I have Torque Pro and my instantaneous MPG meter was at 0.0 the entire time this was happening. When I turned the truck off and back on, the MPG was displaying again normally. This is what made me thing something with the VSS connector.
I decided to search the issue and confirm my suspicions then found out that this could be a lot more difficult to pinpoint. Since it cleared up when I cycled the key I am ruling out a transmission issue (for now).
I plan on cleaning the VSS connector (that's the plug on top of the rear axle right?) and then pulling the cover off the steering column to see if I can see any chafed wires. Is there anything else to check out while I'm rooting around? I will add that my transmission handle has always been loose (I think the original owner used to drive with his right hand resting on the handle).
View 14 Replies
Installed rebuilt transmission 1 month ago. Have noticed reverse has started to go away. Feels like it is slipping or tires are losing traction with a lot of vibration in the steering wheel.(tires are not slipping that's just the way it feels).. Does it worse when trans is up to temp. I suspect feed bolts but want opinions.(Mark K.) All forward gears seem fine with no issues. I have never been under the pan deep enough to access the feed bolts.
View 3 Replies
I have a 2001 F350, 7.3. My service engine light came on and immediately the truck started to run rough and lose some power. I've checked the under the cover connections and they were both connected, I replaced the cam position sensor and I still have the same problem. The worse part of the hold thing is that there are no codes stored so I'm flying bind. Where to go next.
View 8 Replies
