Ford 7.3L Power Stroke (1999-2003) :: F550 Runs Low On Fuel Pressure After Approximately 20 Miles Or WOT Throttle
Feb 7, 2016
Just joined today, I have a 2003 550 7.3. New HPOP, 3 new injectors, new seals on others, new fuel pressure regulator, new fuel pump, sending unit mod to eliminate filters. 733 HPOP pressure, 65 fuel pressure at idle. Truck runs out of fuel pressure after its warmed up and driven about 20 miles. Haven't checked voltage at pump while driving. I had taken it to a seasoned tech of 20 years and he had replaced HPOP and 2 injectors and it does start better but problem is still there.
View 14 Replies
Advertisement
Having trouble with motor, driving home one day heard a noise under the hood. Then a lot of grey smoke started coming out of exhaust. Got the truck hauled home notice fuel was coming out at the number 7 cylinder at exhaust port. Thought it might be the injector just put rebuilt ones in, thought I might have received a bad one. I switch the number 7 injector with the number 3 injector. Did not make a difference still have fuel leaking out of exhaust manifold at the number 7 cylinder and a lot of grey smoke coming out of exhaust. Not sure where to start looking next? Could it be the injector cup is the problem?
View 14 Replies
So I installed my chip today. It's got anti-theft, high idle, stock, 50, 75, 100 tunes.
With the chip installed the truck starts. In all tunes except "High Idle" it idles at about 1000... normally it would be like 500-600. High idle position works (1100-1200 RPM). Anti-theft position works - it kills the truck. The throttle does nothing when pressed no matter which position it is in. Stock, 50, 75 or 100.
I removed the chip and the truck runs fine. Did these guys send me one for an automatic? Or do I have the wrong computer in my truck? My computer code is DAC3 and the truck is a 2000 with a manual transmission.
View 6 Replies
I had a fuse blow today that runs the throttle and we could not move it. Replaced it and it blew again. I think this fuse is blowing because the wires on my overdrive are broken. Is there anyway to disconnect the overdrive until I can get replacement parts? As there not enough wire there to put them back together.
View 1 Replies
Went to start my truck (2003, 7.3 F250) one evening and I found the headlights on. No keys in the ignition and the truck hadn't been driven for 2 days. There was a strong smell of plastic and or electrical components burning in the cab. The truck started without a problem. I shut it off and the lights remained on. Cycling the MFS and light switch would not turn the lights off. I had to disconnect the batteries and leave it till time allowed for trouble shooting.
I've had it in my shop for three months now and this is what I've found so far.
-Source of the burn smell is coming from the fuse panel. More specific it's coming from a bulkhead that plugs into the panel. One pin connected to a White wire with 2 purple traces. I've traced this wire to one of 2 small relay packs in the engine compartment next to the driver side fender. I've replaced the relay this white/purple wire connects to as a precaution. This did not remedy my trouble.
-The local ford dealer told me this relay was for the A/C clutch. I located a 10amp fuse in position 10 and removed it. The headlights finally turned off.
-I started the truck and the A/C compressor clutch still engaged and ran. Smoke began to pour from the fuse panel once again. I killed the truck and head lights remained off. All done with the fuse in position 10 removed.
Here's where it gets weird!
-With the key/engine off and I turn the headlight switch on and MFS to low beam the fuel pump is running. Change the MFS to high beams and the fuel pump turns off.
I've looked over the wiring harness and there are no noticeable problems indicating multiple wires being shorted. How are all these issues related?
View 2 Replies
Every time I hit a hill, loaded or empty, or get on the truck on level ground after about 15 seconds it acts like it's running out of fuel. The pump starts getting noisy like it has air in it, but it'll straighten out eventually. If you don't let off the fuel it'll eventually stall out. No check engine light, no codes. Truck has a ts chip but it does it on all settings. New fuel filter, changed oil with hot shots secret, new air filter, hutch mod done. I'm at a loss for what to do. Good fuel pressure also.
View 8 Replies
I have read many different threads regarding the TPS sensor on the pedal and EBPV deletes on the E99 7.3L Powerstrokes. I am trying to troubleshoot some issues with my E99 7.3L. Usually on cool mornings and after not being started for awhile the truck will seem to be stuck in an Idle. This is an intermittent problem that doesn't always happen.
I cleaned the connections to the Tps and the IVS sensor and put them back in. No luck. On another note I am also seeing a reduction in fuel mileage and power like the truck is being restricted. I don't know if these symptoms are related or possibly their own issues. I am troubleshooting and possibly thinking it is the EBPV system that isn't working correctly. Considering doing an EBPV delete with a NON-EBPV Pedestal and Flange.
View 12 Replies
Low power on my 2003 7.3 F350. The truck runs fine but I can tell it is low on power (seat of the pants). I figured it to be fuel related so changed fuel filter and oil with no change. When that didn't work I installed a fuel guage and this what I found. Key on no start fuel pressure 45 psi. Start truck the pressure will get up to 61psi. Under a load it will drop down to the low 30s. I have dropped the tank mixing chamber screens clean and so was the tank. Changed fuel pump and now under a load it drops to the high 30s. Does this sound like the fuel pressure regulator is leaking by and causing low pressure under a load? Truck is stock besides superchips 1705 programer.
View 9 Replies
I bought an Autometer 4763 gauge that didn't come with the correct fittings to plumb the sender into one of the extra ports on the back of the bowl. I went to the Ace hardware store right across the street and they didn't have anything (not surprised) and then Napa. They couldn't find a fitting to match either. He found that the plug threads are 7/16 20 tpi and the sender is 1/8" NPT. He suggested getting a 7/16 20tpi bolt, drilling it rifle-style, and then tapping it for a 1/8" NPT. The alternative, and what I ended up doing, was to use brass fittings to tee it off one of the supply lines to the heads. I ended up going that route but wanted to know if I should have looked harder for the right fitting.
Here's a pic of what I have now. I've test fit it, and it seems to work although I will need to insulate the hard lines because they rub due to the offset.
View 8 Replies
Looking for pics of where/how they mounted their fuel pressure gauge? I'm getting ready to install one.
View 11 Replies
Next mods are for the fuel rail cross over and the high pressure oil cross over. I see the unused ports will come in handy.
Fuel delivery? any specialty mods to run the fuel lines? I see it's a #4 ORB fitting. Anyone ever use a "T" or a splitter off the fuel bowl to have a quad line set up?
Saw the FRx from RiffRaff .... not sure how it eliminates air from the system 7.3L Diesel Fuel Rail Crossover? (FRx) 99-03 Powerstroke
View 14 Replies
Last night when i left work I noticed my fuel pressure was running about 77 psi, it normally runs about 68psi. today I took my daughter to practice and it was around 83psi, on the way home it was up to 95psi, so I parked it and took another truck to work.
About a week and a half ago I lost fuel pressure going down the highway and the truck died, finally decided my pick-up foot must have come off and had my sister in law bring me some diesel and it has drove fine ever since. (it was right at a quarter tank).
I have the FRX from riffraff and am thinking some pieces of that foot have got into the fuel bowl and plugging up the return. Things to check? Could it be a problem with the fuel gauge or wiring, and how to test them. It is an autometer gauge from riffraff.
It will probably be a few weeks before I can do much more than clean out the fuel bowl. I don't have anywhere inside to work on it and it's been rain/sleet/freezing rain/snow for the last 10 days. I have most of the stuff to do the hutch mod and its next on the list but was hoping to put it off till spring.
View 13 Replies
Ok, I have a early 99 F550 that had a tired engine when I bought it about four years ago, but I kept using it just dealt with the low power and blow by. But last winter I decided the truck deserved a complete overhaul. New cab, new transmission, overhaul the engine, and everything else that goes with. I tore the engine down to find out it was already a ford reman. Had the heads completely gone through, new pistons, new exhaust manifolds, new turbo, brand new injectors, new 4inch exhaust, new valve cover gaskets uvch harnesses and repair ends for harness side, and a new IDM.
Now with everything back together, the truck starts an idles fine but has absolutely no power driving it takes like a half a mile to get to 45mph. No check engine lights no smoke. I took it to ford they said only stored codes were for ebpv which I deleted out of turbo housing they recommended changing injectors. So i did no difference. They also said my hpop was about 1600 at idle. And said that's enough pressure. I did resistance readings on all wires between idm an valve covers.
View 14 Replies
I have 01 F550 6spd 4x4. sounds rhythmic, smooth at idle but just over 1200 is a pattern surge but doesn't sound like one cylinder, cel is off, ICP and pigtail changed as it was leaking , no change. From what I've read duty on ICP and IPR should be about same % I've included the codes I've gotten, I have the epc disconnected right now as I thought it was a wastegate issue, checking the ICP plug next,anything I've missed? It had a cyl 8 contribution at idle which I hear is common? Will changing CPS work with that one? Think it's a grey one. There's no water in bowl I replaced filter, since replaced ICP, pigtail, and bleeding fuel bowl and new filter the codes are gone but still misses, will be checking uvch, injector buzz test showed no faults. Old diesel guy said to flood with Stanadyne fuel treat?
View 9 Replies
This applies to a 2001 F-350 with 73,000 miles on the engine. Engine oil level is good, batteries charged, HPOP reservoir is full and passes Cody test with flying colors. Fuel pump runs for 20 seconds at key on. Start takes about 6 seconds. If I shut the key off and restart immediately it starts in under 2 seconds but if I wait about 30 seconds it's a 6 second start. Here is an AE that I ran on it, it has me stumped. FWIW it seems to start quicker when AE is hooked up. ?? An odd whir type of noise comes out from somewhere under the hood when I first turn the key on and when I clear the codes with AE.
View 14 Replies
The last couple of days with the temps in the 50's, my 2000 F550 with a 7.3, will start normally and idle fine. When I try to drive it, I get less than a quarter mile and it just looses power and will die.
If I flutter the pedal, sometimes it will keep running, very poorly. And when it does this, it is putting out blue smoke. After it does this, it will run fine. Just like nothing is wrong.
What do I look for, or is this normal. I have had the truck since last October and this is the first time it has acted like this.
View 12 Replies
I am installing a fuel pressure gauge into my 02 7.3 I went to the thread the sensor into the plug hole on the fuel filter housing and it wasn't threaded, turns out the sensor thread is slightly smaller and a different thread ... The directions say to install it into the filter housing or the lift pump ... So I'm assuming I have to go the lift pump direction of installing it but where the lift pump is or how to install the sensor into it while not throwing a code or causin problems ... A step by step and even pictures.
View 14 Replies
I just did an engine swap and have an odd noise that I was curious on where to start. It sounds like a buzz test on an injector at 2,250 rpm and gets louder as rpms increase but starts out very faint and get louder. Makes noise converter unlocked and locked in gear under load and free rev no load.
-2002 F550
-Fuel pressure is 60+ psi all the time
-Regulated return fuel system
-New injectors all AD
-Stock tune
-38R turbo
-New flexplate
-injector hold down tight
-new degas res
-new water pump.....
View 2 Replies
I seem to not be catching a whole lot of luck lately. The rear end on my F550 has a bunch of play. Going reverse to drive it clunks pretty bad but no ujoints are bad. I can rotate the yoke by hand and hear clunking so i am guessing the ring and pinion are bad, at 100,000 miles. Seems like the rear ends should be more stout than that, certainly look it.
Where to find a source for reman third members since this one had a drop out? Most axle places won't touch it
View 7 Replies
I just replaced all 8 injectors in my 01 F550 with remans from FFD. I have noticed a constant knock at idle but truck runs great. Blowby has no pressure behind it, truck does not smoke. Does this sound like a problem unrelated to an injector?
It did not make this noise before replacing the injectors
[URL] .....
View 12 Replies
I was driving my bosses f550 with a 7.3, and while towing a loaded 40' flatbed of hay, it started bloing white smoke and lost all power and had almost no pedal feel. It wouldnt even go past 2500 RPM. Then, all of a sudden, it started billowing black, and BOOM backfired and shot flames out the exhaust. Then, I pulled over at a parts store and replaced the fuel filter, which worked for a while, but then it started blowing white smoke again. Once I limped it home and unhooked it, I took it out and let her rev a bit and it seemed to stop blowing smoke, but it still has less than the normal power it used to have. It has 226000 miles and is completely stock.
View 8 Replies
