Ford 7.3L Power Stroke (1999-2003) :: F350 Won't Crank At All / When Turn The Key To Start Power Drops
Sep 17, 2015
New to the forums, not new to fords. 1999 F350 7.3L Diesel. This has been a work truck and has seen multiple devices in and out over the years. I removed the last crap for GPS tracking etc from the last owners. The truck has worked well for a long time since until...
I'm moving slowly to a different state and so the truck got parked for 2 months. went to start it and nothing. the dash comes on and all the lights come on but when you turn the key to start the power drops and nothing.
Testing so far:
replaced the fender Solenoid
tested the starter motor and solenoid -passed
replaced the ignition switch
tested continuity of the hot and ground wires to the fender and starter and everything passed
When I shorted across the fender solenoid the starter works and tries to start the truck (unsuccessfully so far)
So the wire that goes to the fender solenoid is not working and where to trace it to and what needs to be fixed. Is there a relay or fuse besides number 30 that is in the way? where does the magical wire go so i can check its continuity?
I am stuck 800 miles from where i need to be and I am stuck here. I don't have the cash to get a mechanic and my mechanic friends are stumped. I do have a Snapon modus tester, what to do with it.
FYI the batteries are new and fully charged.
View 14 Replies
Advertisement
I've replaced the alternator and starter recently and both batteries and the truck ran fine befor that. But it sat for roughly 2 months and now it seems as if its not getting fuel. Will start with a shot of ether but will die as soon at it burns it off
View 14 Replies
I have a 2000 F350 7.3 ... A couple weeks ago I noticed that it was taking longer to start then it should be. Now I have to cycle the key switch 3 or 4 time to get it to start. There is a clicking coming from the relay block under the radio. Sometimes the truck will start sometimes it has to be rolled off. I have recently replace the starter and alternator. I have had the batteries tested and they are good. I replaced the two small relays in the block under the radio, one is for the fuel pump and the other I understand is for the door locks? I also read on here the large blue one is for the turn signal so I have not changed that one. After all this I still have the same problems.
View 9 Replies
I just started having an issue on my 01 7.3 f350 with 203k miles, it will crank much longer then normal to start. If you shut it off then try to restart right away it starts normal, if you wait 10 minutes long crank again. if you shut it off and turn key back on but don't start it you can wait an hour then start right away. IDM bad? Vacation in 2 weeks and I would like to get this fixed first.
View 14 Replies
A month ago I got into my truck in the morning and when I turned the key to Run everything lit up like normal and after the glow plugs warmed up, I turned the key and there was about a two second delay between me turning the key and the engine cranking over.
The next couple times I tried starting the truck that same morning I had to try to start it a couple times because it wouldn't try to crank over the first couple times but it would always eventually start.
It's been continuing to give me problems but never stopped running once it was started and then this morning I tried starting it for 45 minutes with no luck.
What I have tried so far is:
Resetting batteries
Jumping the truck
Checked to see if the starter is getting power. ( I put wire testers on it while someone else started and I didn't get a good reading even when it did start. New starter was put in 9 months ago.)
I also made sure wire going to starter wasn't corroded
Battery terminals are also not corroded
Checked fuses
Tried starting truck with fan clutch disconnected
Cussing at it
Tapping starter with a hammer while trying to start it
Also, everything sounds perfectly normal when I turn the key, it just doesn't even try to turn over.
View 7 Replies
Alright so I have a 99 7.3l. One day I went to start my truck and when I turn the key to the on position all is normal and then when I turn it all the way to crank it nothing happens. I hear a relay click ann thed that's it. Me and a buddy of mine spent quite some time on going through the entire truck. The starter was replaced, the neutral safety switch was replaced and the ignition switch was replaced yet the problem is still there. We then discovered that fuse #20 under the dash keeps blowing with every turn of the key. The manual states that this fuse is a starter motor relay coil PCM ( gasoline only). So if it's gas only why is it even in there. Let me just say that I can jump the fender mounted relay and the truck starts.
View 7 Replies
I have a 99 f350 Ford 7.3 service truck. It will crank and run but when it gets to 150 or 180 degrees it shuts off and will not crank back until it cools off. I have change the ECM I have change the IDM still same thing it runs till gets hot and then it cuts off. I have changed IPR valve IPC sensor .check the high pressure oil pressure it is around 800 900 at an idle it is around that pressure but when first starts up it is higher once it starts and runs it idles around that pressure 800 900 psi....
I have hooked up my scanner and it shows around 150 degrees oil temperature it shuts off . The high pressure oil stays the same as it was when you first crank it the low pressure crankcase oil is 60 psi ... Once the oil temperature reaches around 150 ~160 degrees the engine will shut off . Once you let it sit overnight or for several hours it might crank up ....
View 2 Replies
I have looked through a ton of threads to see if I can find one similar to my problem but have not. I have stock setup but had a dealer installed anti-theft device. The first time it would not crank, it was like the the anti-theft plug was missing so I checked out the key, tried the spare and finally removed it all together. I checked all the fuses and swapped the Starter relay for another of the same part number.
I later sifted it into neutral assuming it was the P/N Switch and it started. This continued intermittent for several days but then Neutral wouldn't work. I got under the truck and pushed on the actuator rod for the transmission and it started again for a few days. If finally failed again and I had time to buy a replacement switch.
Once installed I verified I had back up lights in reverse but still no crank. I have since pulled off the starter and had it verified as good. Is there more to setting/adjusting the neutral switch or is there something I am missing before I tow it in?
View 4 Replies
I recently (in the last few months) have noticed my truck (1999 F350 duallie) seeming to be running very rich … I pull a 32' trailer with it and noticed on the art few trips the front and right side of the trailer covered with diesel fuel spots when I got home …. It also smells very rich when idling…. The last couple times I started it in the mornings it seems to crank a very long time before it starts …it still runs but its got issues evidently … it has these 3 codes :
P1280
P0475
P1670
The 1670 will clear , but the other 2 I can't clear, they are right back every time you turn the key on …
View 14 Replies
I have an electrical problem and my parking lights will not turn off. I had to pull the fuse in the power distribution box (engine compartment) to get them to turn out.
Pulled the switch in the dash (lights still work) and the switch is good so it appears I'm getting power to the circuit somewhere in the harness? Literally, when I pulled the switch out of the dash and replaced the fuse, my lights came on.
Looking for a schematic for a 1999 F350 SWB 7.3PSD? Perhaps it's a relay gone bad?
View 14 Replies
I have an 02 f250 230,000, first 7.3. I've owned it since Oct and put less than 6,000 miles on it. I have another cold crank no start. New glow plugs and Glow plug relay last weekend. Worked fine that weekend. It sat all week, then crank no start fri night, it was like 70 degrees for the high that day. Plugged it in over night and it started. Did not fire right up cranked it for a couple seconds. I drove it all day, started every time. Valve covers have 5,000 miles on them. Fuel Filter heater fuse not blown. But don't know how to check it for sure. And don't know where to go with it from here. Getting frustrated with crank no starts. No troubles found.
View 2 Replies
I got a 2000 7.3l with 400,000 miles on it that decided to just not start anymore after I parked it for a couple days. Its always been a hard starter due to needing glow plugs but I can deal with that. it doesn't even try to fire anymore. I replaced the CPS (my tack bounces when cranking). The ICP has oil in the plug so I just unplugged it for now till I replace it.
I pulled the IPR and cleaned it really good and bench tested it with 12 volts and could here it clicking so I put it back in. I can get under the drivers door with the key on and hear the fuel pump running. I gain oil pressure on my dash gauge when cranking. I check all my fuses. my WTS light comes on . I just don't have any fancy scan tools to make this easier. Also just cause I was feeling lucky I just went out and bought 2 new batteries for it yesterday so we are good there.
View 6 Replies
I have a 1997 F350 7.3 with standard xmission. Have not messed with it since Oct of last year. Then it would crank but no start. Now when I turn the key there is no wts or nothing the gauges move, and tach moves when cranking, but nothing else.
The cam and crank pos sensors have been changed. The high pressure sensors changed. Now when I hook it to the AE it says cannot connect to truck. Where I need to start? Have checked all fuses that I know about.
View 7 Replies
Friend's 2000 7.3 wont start, just crank and crank tried to fire but nothing in the cold leave it plugged in and it starts leave it in a shop over night and it starts with a shot of either, he is a truck driver and the truck will sometimes sits for 6 weeks at a time this time 2 weeks before I touched it. He wanted me to install a fuel pump so I did and started the following:
Cracked fuel lines to see if I had fuel psi at both heads
I tested glowplugs they all read at 0.3 on all 8
I have power to harness as the same at both sides of the relay
RPM tach jumps
Oil psi gauge rises
Using my phone I can read hpop and 2000 at cranking (how accurate that is im not 100% sure)
All fuses good
View 7 Replies
So I got all 8 injectors upgraded and excited when I get them back I put them all in in kind of a rush. And in that rush I left the cylinders full of excess oil. So obviously when I tried to start it hydro locked. Angry at myself. I kept trying to crank hoping it would fire and just shoot that oil out. Nope, so I went back to taking all the glow plugs out and firing it all back out. Put it all back together then tried to fire her up. Took a minute but she started and I let it run for a while. Hit the gas a few times and then it died. Couldn't get it started again. It would just crank, I checked the icp and ipr and the icp did not build above 35 psi and the ipr was at 98.04% so I just figured the o rings blew out when it hydro locked.
So I took it all back apart put new o rings on, took my time and put it back together right double checking everything. Got it all back together and went to start it, it would just crank around 160-170 rpms, battery voltage at 10.6 icp built up to 140 but now it won't build past 40. Ipr still goes to 98.04. The engine ran just fine prior to injector change, I put a new upgraded hpop prior to injector change, new ipr, icp, cps. Everything checks out, but it will not build oil pressure while crank I've killed a set of batteries then went all out and spent 350 at napa for some optima red tops. I did notice the cylinder 7 injector is the AE injector. It suppose to be in cylinder 8, idk if that's affect the oil pressure building up?
But as far as I know, I'm not building oil pressure. So idk if the hydro lock could have ruined something to keep it from building oil pressure?
View 14 Replies
i have a 2001 f250 7.3L PSD. it turns over but will not run. replaced the CPS , starter and the #30 fuse. IPR is new and all injectors are new, new gaskets and harness and new glow plugs new batteries. still just cranks and cranks. no oil pressure build up and no tach movement, oil level is good in HPOP. What could it be?
View 14 Replies
So back ground is as such. Truck started fine before I replaced the hpop with t500 and did the driven diesel regulated return. I have double checked everything is plugged in. Now when I try to start it cold it will just crank. Yes I get smoke and oil pressure both places. If I give it a shot of ether it will start right up and run fine all day. What am I missing? Yes I know ether bad.
View 14 Replies
i have a 99 f450 7.3 that cranks but will not start. I did an injector buzz test but it sais no communication between the computers. it has a new rebuilt engine, new ipr, icp, hpop, water pump, and both computers.
View 4 Replies
Found icp sensor with oil in plug and codes p1211 and p1212. Icp sensor reading 0 pressure. Changed out icp sensor. Still cranks no start check oil level in hpop resverior, check with brake clean spray nozzle and no oil on it. Filled resverior with oil. She tried to start. Had to put the charger on her and she finally lite off and came to life. Questions, how would that resverior empty out? Was it because I pulled that sensor? Is there s check valve in that resverior hanging up?
View 2 Replies
Anyway, I went out to start my truck just now and I'm getting a weird symptom.
The truck gets partial revolution and then to me it seems like the starter bendix pulls back in prematurely and this nasty clank and then a slight "zing". all within a second.
If I try a few more times, it seems to fire. But all the attempts before it fires sound pretty nasty to me.
Does this sound like a symptom of a bad starter/bendix?
A little further history, my excursion was broken into several years ago and they stole my pioneer head unit, in doing so, they forced the shifter down and since then it has been a little "loose". I'm wondering if it could be a neutral safety switch on the transmission?
Anyway, I'm getting ready to order a new neutral safety switch but wondering if I should go ahead a purchase a new starter as well?
View 6 Replies
I have a 99 F3 50 with the 7.3 L I am done a lot of work to replace the HPOP pump and the ICP sensor as well as the IPR it cranks but does not start it will sputter and smokes but doesn't run SOS. Also there are no dtc in computer....
View 8 Replies
