Ford 7.3L Power Stroke (1999-2003) :: F350 - Cranks Just Fine / Slow To Start
Apr 27, 2015
It's a 99 f350 7.3 diesel powerstroke. About 180k miles I think.
It cranks fine. I just changed the glow plugs(all were dead) but when you try and start from cold, it takes about 7-10 seconds to fire. The oil res is full, tried disconnecting the EOP sensor, still fires up and takes just as long. There is one near the oil filter, and that seems to not be it either.
Doesn't smoke, no oil leaks that I know of. Not sure what else to check before sending it to another shop to get put on a diagnostics machine. I read about the IPR, but it has no problems when running. Only problem is a very long time to start. Also changed the fuel filter.
View 3 Replies
Advertisement
My dad has a 99 F250 with a no start issue. Everything was starting and running fine one day. The next he gets a no start. Cranks fast and fine but wont fire up and start. He has a scangaugeII hooked up to it and his oil pressures and volts look fine. His tach moves when he is trying to start it. He checked the icp sensor and it had oil through it so he replaced it with a Ford part. Unplugged it and the scangauge pressure goes up but no start. He also replaced the ipr with a new Ford one just in case. He checked and is getting low pressure and high pressure oil.
I am having him check the fuel heater fuse #22 to make sure it is not blown. He had the block heater plugged in all night along with a battery charger to make sure they are topped off as well. We have gone through a couple of the checklists on this site for a no start condition but nothing has solved it yet. I think he is sitting at about 200k on the motor. No major issues or problems until now. He is currently also pulling the ICM to check it out as well. No codes are being thrown.
View 14 Replies
My '99 f350 lost a lot of power the other day, turned out the the injector harness got unplugged. So I swapped those out for oem ones, ohm tested the uvch and injector harness, put a brand new GPR, and still nothing. Cranks over but won't start, what else could it be?
View 5 Replies
I have an issue with my 2001 f350 7.3 PSD. Intermittently it will not start. It will crank really quick, but will not even try to start. I think it is not getting fuel. There are no CEL codes and I have a WTS light and the tach is moving while cranking. I hear a clicking/buzzing sound coming from under te center opf the dash. When I hear that sound it will not start. checked fuses and relays and it started before. not sure if removing the fue made whatever reset. this has happened a couple times. Now it will not reset. When I remove the number #24 fuse under the hood, the clicking stops. when i crank it, but still doesn't start. When it starts in runs perfect. Drained the batteries trying to trouble shoot, but have them charger now.
View 14 Replies
2001 F350 7.3 ... Below 35 degrees, truck is hard to start. Cranks for a while, sputters, dies. Repeat a couple times, finally starts running rough, surging and loping for 10-15 seconds before it settles down and runs smoothly. Recently had all glow plugs replaced. Next cold start didn't show much improvement (not as bad as sometimes, but wasn't very cold either).
Surfing here and other forums, I see suggestions about letting glow plugs heat longer after WTS light goes out. Some suggest as long as 60 seconds. In the past, I have tried waiting a little while longer after light goes out, or turning key off/on and letting it cycle again. But I've never really timed how long I was waiting.
We're having a warm spell right now, so I can't do much testing. But yesterday morning was about 30. I timed the WTS light and it went out after 10 seconds. I waited another 20 seconds.. about 30 seconds total. Starting seemed a little better than usual, and there was about 1 second of roughness before it settled down.
I need to do more cold weather testing to be sure, but it does seem like it might be better to wait longer than I have been.
On the other end of the scale, I saw a comment that glow plug cycle is dependent on oil temp, and they don't come on at all if oil temp is above 40. Is this correct? If so, is there any good reason to wait to start in warm weather? I'm usually pretty diligent about waiting for the light regardless of weather, but the truck doesn't seem to object if I get impatient and start it sooner in warm weather. If the glow plugs aren't even on, why wait?
Should I just totally ignore the light, and wait for some interval (or not at all) based on a semi-educated guess about how much glow plug time might be necessary for the current temp?
View 14 Replies
2000 F350. Starts great. Idles fine. After it warms up a little, it will run rough and lose power like it is only hitting on a few cylinders. It will eventually stall unless I push the clutch in and bring it back to idle and then it smooths back out. I figured it was starving for fuel but I can rev it with the clutch in with no issue. I ran it up to 2500 rpm and held it there with the clutch in and ran perfect.
I let the clutch out and start rolling....missing again. The check engine light does come on but my scanner says that there are no codes stored. If I idle it, it will smooth out, and the light goes off. All I have done so far was change the fuel filter which was almost plugged shut and the housing was full of rust looking debris which I cleaned out. BINGO! Nope. Same issue.
I am really at a loss as to where to start. I bought this with 120k on it and it now has 170k and I have not had to do anything other than routine maintenance.
View 14 Replies
While driving my 99 F350 7.3 it died and I was lucky enough to coast home. No WTS light, no tach movement when cranking, no fuel pump, no CEL, Cranks great but no smoke or fire. New CPS & PCM still no lights or tach. Moved relays checked all fuses. WTF is wrong?
View 14 Replies
Went to the store came home no problems. Went out to go to work next morning truck won't start. Cranks just fine just doesn't try to run. Was not getting voltage at ficm replaced board in ficm have correct voltage now but still won't start
View 2 Replies
I'm TSing a no-start on my 2005 6.0L F250. Engine cranks fine. I've been working my way thru the TSing guide and using my new ScanGaugeII. No codes found. At glow plug warmup, (dash light goes off), I'm getting 40.5v FMP, 11.0v FLP, 14.8% ICP, and 0psi IPR. After cranking for 10-15 sec, get 35.5v, 10.0v, 84.7%, and 446psi. I've had a trickle charger on all night to keep the batteries charged. Have not seen FMP over 45 or IPR over 470.
View 14 Replies
Went out to start my truck this morning and it wouldn't start. Cranks fine and almost started once but died. Checked all fuses all my voltages are good. Oil and coolant are good. When I turn the key on I can hear the fuel pump and sounds like it's priming correctly. Might be an issue with a clogged fuel filter? Maybe? Haven't had any problems or issues otherwise.
View 6 Replies
I bought a 99F350 with a 7.3, it was not running when I bought it. Batteries good, new starter, turns over just fine, fuel pump works, but now I don't know what to look for.
Was testing ohms for my injectors and at the plug on top of the driver side valve cover, couldn't get a reading at all, tested the ohms at the pass. Side valve cover plug and got good ohm readings.
View 14 Replies
Truck is a e99 f250sd 4x4 7.3 manual trans. The truck started and ran fine to work this morning. Went to leave this afternoon. Hopped in, put key in and tried to start it. Engine just turned over, never started. Thought that it didn't start because I didn't let the plow plugs warm up enough. Turned ignition off, turned back on and let wait to start light to go out. Same thing happened again. Just turned over but wouldn't start. As far as I can tell the fuel pump is running. Felt it vibrating while the ignition was on. What to check.
View 14 Replies
Ive got a 99 7.3 with 250,000 miles on it. It has run fine all day but just jumped in and won't start. It cranks over but won't fire. Check engine light doesn't come on. About two weeks ago it cut off twice at idle but haven't had that problem since.
View 2 Replies
I have a '99 7.3 that I am working on for a friend. He was moving out west and got to the next state. He stopped to use the washroom, when he came out, the truck would crank but not start. He had it towed back to my house. I have some diagnostic information. Fuel pressure measured at the fuel rail in the head is 60 PSI for the passenger side head. I pulled the plug on the drivers side, it was under pressure and sprayed fuel.. I did not measure it there.
WTS light comes on and then goes off in a normal time frame. Tach shows around 500 RPM while cranking. Engine oil pressure on dash gauge builds up and Low Press Light goes off. Pulled the plug on the High Pressure Oil Res., oil is present at the top. Are there any other checks that I can do until I can get a scanner. My friend has a Snap-On, but he's almost 100 miles away.
View 14 Replies
My Mazda has 50k miles on it. I have recently gotten a new job where I park my car in a covered parking garage.When the car is parked in this parking garage It cranks fine but it is slow to start. The car does this odd behavior only inside the parking garage when I am coming home from work. It starts fine in the morning. Recently I did not start it for 2 days, and it cranked up and started just fine. I am not sure what exactly is wrong with it. My other question is how long is too long, is a 4 second start time too long or am I just over thinking this one.
View 2 Replies
I have a 2003 f250 with the 5.4 in it. When I bought the truck the odometer and fuel gauge weren't working. So I tried disconnecting the battery and when I hooked it back up the odometer started working again and the fuel gauge went from below empty up to full then just dropped back down to below empty and won't move at all. I haven't tried disconnecting the battery again. And I know more than likely I will have to replace sending unit but trying not to if I don't have to.
View 6 Replies
This past weekend I noticed I was loosing boost pressure on my 2003 7.3l F250 so I pulled my turbo out found the problem fixed it then put the turbo back in. After it was all said and done I went to start the truck up and it just cranked and cranked a cranked but no start. Worried I didn't hook something up right I checked and rechecked everything to do with the turbo, all good nothing out of the ordinary.
I tried to start again, nothing. Spent all day yesterday trying to figure this out. Replaced the cps still nothing. No movement in tach but I don't remember any on startup anyway. Drained the fuel filter had adequate pressure and such but replaced the filter anyway. Still nothing. Checker all my fuses, one by on and non were blown but I still tried disconnecting my fuel bowl heater and still got nothing. I tried disconnecting the Icp still nothing. There was no oil around the icp either.
I'm getting frustrated that the truck wont start, the truck ran perfectly fine before the turbo removal but now wont even give a sign of kicking up. Just cranks and cranks. Also checked Hpop to see if that's the cause and it's filled like to the brim. But when I'm cranking the truck about 10 sec into the oil pressure gauge kicks up and reads good but only when cranking.
View 7 Replies
I have a 2002 f350 psd. I pulled it inside today to wash it. After washing it wouldn't start. Pcm is working. No oil pressure on guage and no reading on tach.
View 9 Replies
Truck cranks wont start. Fuses and relays good, New motorcraft; IPR, ICP with pigtails, New T500 hpop, New 180/80 Injectors, Push rods, 910 valve springs, Mellings lpop. Motorcraft oil cooler.
Reservoir full, oil new 15-40w Amsoil, Rails full, Fuel bowl full and clean, HPOP drive gear rechecked and torqued.
RPM 180
Temp oil 88*
ICP duty cycle koeo 14.8, crank 64.85
ICP pressure 250 -450psi
ICP voltage .27-.50
Manual gauge on oil rail 250 -450psi when cranking
Inj pulse width .0005,
Buzz test was good
Vref 5v all sensors. 12v at IPR w/koeo
Fuel pressure 58psi
Air test hpop hear no leaks with stethoscope.
DTC codes: P1280, P0380
Also put straight edge across injectors to double check they were seated.
View 11 Replies
I have a 99 Ford e350 7.3 Powerstroke with about 150000KMS on the clock. However I am having a really hard time starting it in the Cold Canadian Winter (-30). Last week I changed all 8 glowplugs, the batteries, the oil, fuel, fuel filter and yes i always keep it plugged in.
It cranks really well, but it just wont fire not even with a shot of start fluid. I don't know anything about these trucks much less a diesel engine. A guy took a look at it and said my engine needs to b replaced. (I think he is wrong)....
View 11 Replies
My 99 F350 cranks, but won't start, and the "water in fuel" light on the dash stays on while cranking. I have never paid close attention to it in the past. Is it supposed to be on while cranking?
I drained the water from the yellow lever located on top of the engine, and tried to start it. The light went off for the first few cranks, but again the truck still will not start.
I just came from a 10 hours round trip to NC. I filled the truck up two times from gas stations on the way. Is it possible that the fuel is bad? I drove on the same fuel almost 3/4 of this tank and now at the last 1/4 I am having this issue.
A little update:
I took the top of the fuel bowl off to see what the filter looks like, and it is nasty and completely black. I could not tell if the fuel in the bowl contained any water, but it looks greenish and uniform, no the obvious separation that happens when you mix water and oil.
Could the fuel filter be the problem?
A little history about the truck. It's always hard to start if cold and not plugged in overnight. I know it's the glow plugs relay, so I just keep it plugged in all the time until I get a chance to fix it.
IDM was acting up shutting off half of my engine, but I took it off, cleaned it, plugged it back in and it has been working fine for over 2 months.
View 14 Replies
