Ford 7.3L Power Stroke (1999-2003) :: F250 - Transmission Cooler Line Leaking?
Jul 28, 2016
I bought a 2003 F250 7.3 Powerstroke from a buddy of mine with 99,500 miles. It is a former Michigan truck and has some significant rust issues. Oil pan and drivers door will need to be replaced in the not too distant future. And probably bed rails later too.
In any case, I noticed a puddle of tranny fluid on the driveway when I got home today. The passenger side line at the fitting into the bottom of the radiator has corroded through. The fitting into the radiator is pretty rusty, and the line fitting is darn near destroyed. The line itself actually has a hole in it.
I see the same part numbers on different sites with different descriptions. Driver side here, passenger side there, inlet here, outlet there. For the same number.
As near as I can tell, Dorman number 624-059 is the outlet line from the tranny to the passenger side radiator fitting, and should be the part I need. Correct? Dorman 624-058 seems to be the line from the OTA auxiliary cooler and back to the tranny. What I cant find is the line from driver side radiator to the OTA cooler. That fitting is corroded bad too, and I may as well do both of them.
View 9 Replies
Advertisement
As explained in the photo annotations, I can't figure out how to remove this line from the radiator so I can remove the radiator for cleaning.
View 7 Replies
Transmission oil cooler line, lower one, is leaking. I think to use pvf, black ones, brake line instead of new transmission oil cooler line. I did replaced upper one with new transmission oil cooler line before a few years and it is rusty already as those line are only zinc plated as opposed to plastified brake lines.
View 12 Replies
So my 2000 f350 is leaking transmission fluid from the cooler line. It goes to the rear of the transmission, but where does it go to from there?
View 5 Replies
So changing the oil in my truck the other day, I noticed the exhaust clamp at the union between my down pipe and first section of my exhaust has been rubbing the trans cooler line and there's a Nick in the granny pan. Lookin at the rubber grommet on the hanger, its stretched tight and looks like the exhaust has shifted over. What could have done this or possible fixes?right by now it's got a gob of high temp silicone acting as a stand off. Don't wanna put the new line in until I have the situation remedied.
View 10 Replies
I have 2002 F150 5.4L gas 4X4 Lariat FX4. Last winter when it got to -30C here in Manitoba one of the lines near the power steering cooler began to leak. I had just bought this truck and upon investigating found that the original line had been replaced and reattached with hose clamps. I had this "farmer fix" redone but then this winter when it hit -30C it blew apart. Obviously something happened to this line before I got it, so I am curious if there is an issue with these power steering cooler lines when it gets really cold. Should I just get factory lines installed and hope for the best?
View 3 Replies
I have a 2008 Ford F250 V-10 Superduty and recently I had a transmission cooler line start to leak. I ordered replacement lines and the tool for the quick disconnect. The line that's leaking is from the radiator to the quick disconnect. I was able to replace the one line, however the second line (problem area) has been a nightmare. The line cracked right at the quick disconnect fitting.
The hard line is tight in the fitting and corroded. broke the tool trying to remove from disconnect. The line is flush with the quick disconnect. How to get that out of the fitting? or another method of fix? Its a hard 1/2 line going into connect crimped to rubber line going to transmission.
View 13 Replies
I've had my early 99 f350 7.3L for a lil while now. Starting to see few problems surfacing. while doing my weekly fluid levels found oil in coolant and after looking around found oil covering bottom of driver side engine. As far as i can see it looks like oil cooler leaking from front side.. Should i just replace oil cooler or rebuild?
View 4 Replies
New to me early 99 (4/98) f350 7.3 6 speed. Truck started acting up a few days after I bought it. Return line at fuel bowl was leaking, so started there and found a bad seal on the Fpr (unrelated to the fuel leak due to disentegrated compression sleeve). Fast forward through a bunch of parts swapping that still resulted in miserable lift pump pressure readings, I pull the sending unit out of the tank, expecting to find a plugged screen.
Well, there was in fact a plugged screen... Attached to the bottom of an in-tank pump. How did that get there?!? Everything I've read says there should only be a pickup tube??? Should I get a new sending unit from a junkyard and do the hutch mod or???
View 9 Replies
My HPOP was leaking so I pulled it our last weekend along with the fuel bowl and put all new seals in. All my previous leaks are sealed but now this stupid fuel bowl is being a major PIA.
The return line coming off the FPR will not stop leaking! It was slowly dripping when I first replaced the bowl and I thought the leak was between the fuel bowl and FPR housing. I ordered new rings and put it back together.... still leaking.
I wrapped a towel around the fuel fitting and realized that is were the leak is actually coming from. I went to the parker store today and got 3 new 60VL5 sleeves. The first one tore while sling over the fuel line (I was using 2cycle oil as lubricate). The second one leaked even worse.
In a desperate attempt to stop the leak, I slid the sleeve onto the fuel line as far back as it would go. I inserted the fuel line into the bowl and then put a thin coat of rtv on the exposed fuel line. I slid the sleeve over the rtv and then put a light coat of the outside of the sleeve. I tightened the nut up and am waiting for things to dry before trying again.
Why is this fitting giving me such a hard time? I've pulled the FPR housing and it is not cracked so I don't know what the deal is.
View 6 Replies
The fuel line on the passenger side under the turbo that leads to the head is leaking looks like from rubbing on the pedestal, anyone ever just cut it and throw in some fuel line and hose clamps?
View 14 Replies
I picked up this 2004 Chevy Venture for my daughter and it has a power steering fluid leak coming out of the power steering cooler line that runs along the frame in front. I know that the procedure to replace this line calls for disconnecting the intermediate shaft of the steering and lowering the subframe to gain access to the line connections on the rack. My question is, is it possible to replace that line without lowering the subframe? I ordered the new line and it's on its way. I wanna do the job right.
View 3 Replies
I let a small leak that I thought was engine oil go too long it appears before checking the transmission which had still been working ok. I added a whole quart of Lucas and then another quart of Mercon so the level was pretty low. What to do next as I am about to leave Alaska and go back down the highway. Is my ZF trashed now? Still seems to work fine. Or is there a seal somewhere that I can change?
View 6 Replies
I have a 7.3 and I think it's leaking oil out of the HPOP but I'm really not positive.
View 2 Replies
I purchased the truck over a year ago and never had a problem with the transmission. The only issue was a leaking transmission pan gasket so I changed it put the same fluid that came out back in it since it looked brand new and didnt smell burnt or anything. So fast forward time and my girlfriend was driving the truck over the winter and lost control of the truck and spun it around and hit the front end of the truck into a rock wall.I have a weston bar on the front end that took the majority of the hit.
Shortly after the transmission would start to run warmer than normal. It would be 20 degrees outside and my transmission temp sensor would be reading around 140. Now that the weather is getting warmer the transmission is heating up a lot more. I took it to a guy to have him look at it and thought maybe the cooler was clogged or something like that and possibly put a larger cooler on it. He called me up a few days later and said their was a larger cooler already on it but it was not hooked up. It is a black one mounted on the front of the radiator. He said he cut the lines off of the old one and there was a slight bend in the one line so he cut a little higher than that line and then hooked up the cooler.
He told me he blew in the lines and there was no restrictions in it, i guess no pressure when we blue on the lines. I drove it home and the temp went higher than ever before up to 220. The cooler on the front was ice cold and trans pan was hot.I am starting to think maybe the bypass is bad and the fluid isn't getting to the cooler. The fluid is still pink and does not smell burnt so I want to fix the problem before any issues arise. The truck has 137000 miles on it. I have attached pictures of the cooler that he said was already there but not hooked up.
View 13 Replies
I have a 2003 Excursion with a 7.3 and 240,000 miles. I have oil leaking around the transmission and the local diesel shop found the pedestal leaking. I installed a new pedestal from Rotomaster Part # A1382205N. It came with new O-rings and turbo bolts. I ran the truck and it began leaking again. Thinking I had pinched an O-ring I pulled it apart again but found nothing. I cleaned and inspected everything and reinstalled. Its still leaking. I used a straight edge to ensure the sealing surfaces were straight.
View 14 Replies
My transmission on my 2002 7.3 4x4 is pouring fluid from somewhere above the rear of the pan. I thought it was the pan at first. I pulled it off and replaced the filter. After adding fluid while it was running for 4 or 5 minutes it started pouring again. It's not the pan. It's coming from above the pan somewhere. It won't leak unless it's running. Is there a place it can leak on top??
View 7 Replies
Anyway I have a 2001 F250 7.3l 4X4 supercrew 8 foot bed. Have an upgraded turbo, 4" exhaust from turbo back, k&n cold intake. Has 207,000 miles on it, 198k from first owner, the rest from me. Anyway the transmission is a automatic R4100 tranny. Since I have owned it it would shift from 3rd to 4th on slight grade. It would continue to shift up and down till I got back on flat again, rpm's would not vary to much depending on the grade. So that problem continues and now today I was towing a 14' trailer with 3 wheelers on it and I smelled smoke. Pulled over and it was pouring oil from the bellhousing. I had no choice but to drive back home about 20 miles. I first stopped and poured 2qts of ATF fluid in and then babied her home. What are my options here, what I should be looking for to fix?
View 1 Replies
I'm presently traveling and my '02 F-250 with a 7.3 PowerStroke has developed a pretty steady drip of what I am almost sure is diesel fuel. It's dripping from the very front, from the shroud around the fan and radiator area.
I have some basic tools with me, but no experience on this engine or the fuel system. Does the fuel line go up into the radiator area? What should I be looking for? I'm stranded in a campground until I figure this out.
View 14 Replies
I've just (a couple of weeks ago) purchased an 03 Santa Fe. I noticed some trans fluid on my driveway a week later, and not a small amount. I took the lower cover off of the engine, and the leak is coming from the transmission oil cooler area. I had hopes that it would be something fairly straightforward to repair, so I got a replacement oil cooler and some spare hose, just in case it was just a hose. After getting the front bumper off, I found that the bottom of the oil cooler is clean and dry-- not the issue. It looks as though the leak is coming from what they're calling the Trans oil cooler "tube assembly", as illustrated on the Hyundai Parts Department trans cooler page as item number 5, part number 2547126011. Am I correct in assuming that I'm going to have to remove the entire radiator to get to this thing to replace it? It appears to be fixed in place, but I can't see any hardware to remove it.
View 10 Replies
2003 250 superduty 6.0 ... I had to do the icp sensor. I went in from the top and discovered that the oil cooler was failing also. Replaced the icp and the oil cooler. Got it all back together. It would crank but wouldn't fire up. it did try for a about a tenth of a second. that's as close to firing as it got. The shifter has been loose. i ran it through the gears and the back into park. now it won't even crank.
Took the starter in to have it tested. it tested fine. Went to put it back on the truck. With no real force tightening the electrical connection it just snapped off the solenoid. put a new solenoid on it. Still no crank. Checked all related fuses and relays. They all seem to be good.
When I turn the key to on I get the buzzing noise and everything. Been through a lot of the no start check list. I don't have the ability to quite test everything. But what i can check. i do have an obd2 scanner. I cleared the code for the icp. I don't have any other codes showing. I have tripled checked that. After the weekend I am going to have to give up and take it in I think.
View 14 Replies
