Ford 7.3L Power Stroke (1999-2003) :: F250 - Transmission / Torque Convertor Slipping
Oct 31, 2016
My son bought a 1999 F250 Diesel about a year ago. The seller gave him receipts showing that the 4R100 had been rebuilt and a new T.C. installed 25k miles before the sale. The problem is that it is slipping. He says it started with 2nd gear, now it will hardly move in 1st.
Fluid smells a little burnt. We pulled the transmission pan expecting to find lots of friction material. It does not have as much as I thought it would, not as much as I have found in the the pans of the few other auto trans I have seen with worn out frictions. Below are pics of the inside of the pan.
Or, is it the T.C. that is slipping. I have never had a vehicle with a bad T.C. How do you diagnose it? I have experience rebuilding (GM) Turbo 400's and 4L60's. Never had a ford AT apart.
View 3 Replies
Advertisement
My '01 f350 up and running the last 5 years. The truck has 130,000 miles on it and the transmission quit on me two weeks ago. My mechanic pulled the tranny and sent it to a very reputable rebuilder for a complete rebuild. My mechanic then reinstalled the tranny. I picked up the truck and when I paid the bill my mechanic told me that the rebuilder provided a new 4-plate torque convertor and that I would hear it rattle when I was at stop signs, stop lights etc. and that this was normal for these types of torque convertors. I have searched this forum and found all kinds of reasons for this rattle. None of which tell me this noise is normal or should be expected. I have no problem going back to my mechanic and discussing flex plate cracks, engine/tranny misalignment or any of the other causes...
View 2 Replies
I bought a "rebuilt" 2wd AOD off craigslist for my bronco 2wd conversion that ended up needing re rebuilt due to wrong parts installed,since it was a bearing issue and worried about metal shavings I did not reuse the 2wd torque convertor and used the one from the 4x4 trans since I knew it worked. Are there any differences in a 2wd vs 4x4 convertors like stall speed to keep the motor running a little higher for off road performance.
View 1 Replies
I was driving my 7.3 down the road and it started acting like the trans was slipping, it revved up and tried kicking down a couple times and when I slowed down and went to speed back up it just had no power coming through the trans to the wheels it just revved. I put it in neutral and it idled up for about 5 seconds. I put it in park n shut it down. I fired it back up after looking everything over and it moved about half mile down the road and no power to the wheels again. The trans is full of fluid, is there a sensor that could of went bad or just the torque converter or the entire thing shot? Only owned my truck 6 months has a trans and motor swap already from previous owner. 180k on current motor n Trans. 382k on my truck. t6 4" turbo back banks exhaust only mods I know of.
View 11 Replies
My tranny is acting odd. I put in drive and seems to slip a lot in 1st, barely even move at some times. If I put it in 1st with the shifter it goes in and grabs then I can shift up to 2nd or drive and there aren't problems. It drives normally when not from dead stop.
Transmission has 50k miles on it since replacement. Fluid level is normal. I don't tow and drive it particularly hard. I will have to go back and look at miles since last fluid change. I should be right around 30k miles since last change.
View 11 Replies
I have a 2000 Ford F450 7.3 4x4 dully with a PTO driven winch 108,000 miles. The truck has develop a transmission slip.
I have changed the transmission fluid twice and it drives better but it slips badly. I can drive it up to highway speeds but it has problems getting from 0 to 10 MPH. The transmission runs hotter then normal but nothing major maybe around 205 degrees
Do I need a complete rebuild? This is a beater truck that I use to tow mainly. It is not worth a major investment. I need the PTO gear and 4x4.
I have several 2000 through 2003 7.3 E350 and E450 short school buses. Does the transmission from these has a PTO gear? I am thinking of pulling the transmission from one of them and swapping it.
It looks like the transfer case just bolts to the back of the transmission; I believe that a 2wd van 7.3 transmission will work with the 2000 F450 setup.
View 2 Replies
I recently bought a 1999 F250 Super Duty 4x4 7.3 Powerstroke MT with 280,000 miles. The reverse is out and after reading several posts am I to understand that any ZF6 well interchange in it or is it year specific. Guess what my question should read "What year vehicles well the transmission interchange and that there isn't any difference between trucks that run this motor with MT except for the powertrain, like F250 F250 super duty F350 and so on. The second question is how hard would it be to fix the reverse myself. I do have some mechanical experience. Except for the reverse, the trucks run perfectly.
This is my first diesel truck . I'm also confused because it has an adjustable gauge mounted on the bottom of the dash that you can select the performance from. I was told it has a performance chip and that's what that was for. I was told by the man I bought it from that the truck had been bullet proof but I don't know a thing about diesel upgrades or what to look for if it has. Except for reverse, everything works. Low high 2x4 & 4x4. Got it because he had to pay the bail bonds man. Guess I got a deal on it I was told.
View 2 Replies
I bought a 2003 F250 7.3 Powerstroke from a buddy of mine with 99,500 miles. It is a former Michigan truck and has some significant rust issues. Oil pan and drivers door will need to be replaced in the not too distant future. And probably bed rails later too.
In any case, I noticed a puddle of tranny fluid on the driveway when I got home today. The passenger side line at the fitting into the bottom of the radiator has corroded through. The fitting into the radiator is pretty rusty, and the line fitting is darn near destroyed. The line itself actually has a hole in it.
I see the same part numbers on different sites with different descriptions. Driver side here, passenger side there, inlet here, outlet there. For the same number.
As near as I can tell, Dorman number 624-059 is the outlet line from the tranny to the passenger side radiator fitting, and should be the part I need. Correct? Dorman 624-058 seems to be the line from the OTA auxiliary cooler and back to the tranny. What I cant find is the line from driver side radiator to the OTA cooler. That fitting is corroded bad too, and I may as well do both of them.
View 9 Replies
I have a 2000 F250 4x4, it has been sitting in my garage for about 3 weeks. I cranked it up and backed it up about 10'. A few hours later I noticed a lot of transmission fluid on the floor. I remember hearing a hissing sound when I cut it off but didn't think anything about it. The fluid is on passengers side of truck, right side of the engine. Most of fluid is toward the rear but some ran down in front of the axle also. It's up high also, I've got fluid on rear of valve cover. I've cranked it up and let it run but can't get it to leak. Where did all this fluid come from?
View 5 Replies
What are the torque specs for tie rods for a 4x4.
View 4 Replies
Thought I had these bookmarked but not. What is the torque value for the 13 mm bolt , replacing the tensioner.
View 4 Replies
I bought this truck with a stock automatic transmission and 260k miles back in October expecting the transmission to be the first thing to go. Recently I had a transmission code, OD OFF light flashing, for the bad speed sensor which i got replaced. Then the OD OFF light started flashing after some hard driving when I would put into neutral or park so I took it back to the mechanic, Hanahan Truck and Auto in Sc. They looked into it and there wasn't any different code in the system but they noticed when you lay into it driving it slips some between 2nd and 3rd gears so that could cause the computer to put in a code.
They said usually a rebuild runs from $2k-2.5k and they also recommended a Jasper reman for roughly $2.8k which comes with a 100k mile 3yr warranty. So I figure replacing the transmission is probably the way to go. Any recommendations for a replacement. I've heard ATS and Sun Coast are decent options that I could build one. I'm looking to stay close to $3k. My truck is a 2000 F250 lariat 4x4 with 268k miles. I'm installing an S&B intake, 4" MBRP exhaust, and DP-Tuner's F6 chip when I get the transmission work done.
View 11 Replies
So my transmission drove perfectly fine I just wanted to put an upgraded torque converter in especially after driving a customers' truck with a low stall converter. I know their not like for racing or anything but it's a work Truck with some mods to the motor nothing crazy. So I went ahead and bought a low stall triple disk converter and I drove around the block fine and went to go on the freeway and got into fourth but lost it as I hit 75 (was not flooring by any means and had it in the stock tune) now it will not go past second gear. Once it did this the o/d off light started to flash and I decided to do a stall test.went to 1800 in a Second. Suppose to stall around 1200-1300.
2000 f250 7.3 powerstroke dp chip stage 1 camshaft and 180/100 injectors coming at some point but stock for now
View 3 Replies
1999 7.3/4r100 4wd with the rattling torque converter.
I bought this truck 10-11 years ago to use as a tow rig for my landscaping company. It has been a great problem free truck, I have done brakes a few times, a water pump, ball joints but no issues with motor/drivetrain.
I don't know the history of the trans before I purchased. Ford didn't have history of it being replaced and even now it still has all the labeling on the case. I would have thought it would have been washed off in a rebuild. Again I don't know. When I bought the truck it shifted nice and crisp, having owned trucks before it made me think it had been rebuilt but this was my first and only 4r100. Other trucks are ZF6 manuals.
Anyway 10 years and 100,000 miles later it still shifts very crisp and fluid, has been changed a couple times, is nice and cherry red. I added a 6.0 cooler, temp gauge and filter. Never see the temp rise and haven't seen much in the filter.
About 25,000 miles ago the TC started to rattle, a known 99 problem. I figured surely the trans would go and I would do a rebuilt from Ford. It keeps going though so being a work truck I have kept running it.
A couple weeks ago the starter just spun and wouldn't engage. I pulled the inspection cover and noticed some missing teeth on flex plate. Got it to start my turning crank bolt a bit to good teeth and the starter caught. Now we are carrying a breaker bar and socket. It has happened a few more times so I need to replace flex plate.
Question is, since I need to pull trans to replace flexplate, should I replace TC (I would like to get rid of the noise)? Some people have said I will be replacing trans in a couple months if I mess with it. They say just spend $3000 on a rebuilt now with a converter. Not trying to be cheap but hate to just dump this trans that is still working great and has served me well.
I have replaced many transmission and done clutches in many trucks so I am familiar with the steps of removal and installation, just stuck on what I should do.
View 14 Replies
I will be changing all the glow plugs in a few days. Should I re-torque the head bolts or anything while I am in there? Don't want to button it back up and then wish I had done something while in there.
View 14 Replies
I have a 2001 F350 with a PCM labeled "PMT2".
The SES light is triggered every time I try and pull fault codes using Torque Pro. It has done this since I installed Torque Pro many months ago. Same thing happens in another local member's (2000) truck, although I don't know his PCM version.
I'm very comfortable with the Torque Pro settings that have been detailed in other Torque Pro threads. I have been careful to choose conservative settings, including trying debug mode. I have uninstalled and reinstalled Torque Pro to see if that solves the problem - which it does not.
Question: "PMT2" PCM been able to pull fault codes using Torque Pro without tripping the SES light?
I realize another variable may be my OBD2 Bluetooth device. As an aside, I have removed the AIH and would expect to see a fault code but Torque Pro reports no fault codes.
View 8 Replies
The SES light in my 2001 7.3 came on about a month ago while I was towing a light trailer in the SoCal mountains. When I got home I spent about 2 weeks replacing the injector o-rings and glow plugs. I discovered while I was in there that the head bolts on the driver's side where loose. I retorqued them to spec.
Both batteries were disconnected for the 2 weeks. When I started the truck the SES light was still on.
My Torque Pro app isn't showing any error codes, and is reading live data correctly. (I didn't have the app when the light first came on; I only purchased it after I finished the repairs). Am I missing something? Is the SES light not necessarily connected to fault codes? If so, wouldn't it reset after 2 weeks with the batteries disconnected?
View 5 Replies
I have been reading here about alternate methods to torquing the hold down bolts for the injectors. This winter I replaced my old stock split shots with new alliant single shots. I installed the injectors into a cold engine and torqued the hold down bolts to 10 ft lbs. I did not ever go back and re-tighten.
Is it suggested to go in and re-tighten the injector hold down bolts to 10 ft-lbs after the engine has been heated up and cooled down? What are some symptoms of a loose injector? I am imagining premature wear on the injector cups, low compression and maybe some mixing of oil into the combustion chamber.
Did just throw the injectors in and go back later to retorque only to find they were all fine or were some loose?
View 14 Replies
I'm working on a couple of repairs and have encountered a few questions:
1. Are the bolts supposed to come out of the top of the end link? Mine don't so I don't know if that's the way it is or mine are so far gone that they are frozen in the sleeve. My poly bushing kit does not have any new bolts so I'm hesitant to lay into it with a 10 ton press and ruin the bolts (I don't know how much they are from Ford to buy or if I can even buy them).
2. HPO rail plug. I'm removing my HPX as I'm tired of it leaking (hopefully when my HPOP comes back as a T500 I won't need it anyway). I've seen 33 ft-lbs and 96 ft-lbs. As I go towards the 96 ft-lbs it feels like I'm going to strip the threads out so I backed off and they are at 33 ft-lbs now (I don't need that headache and my wife would go through the roof). I got the ones from Riffraff as I misplaced the ones I took off 8 years ago (go figure). The HPO line connections to the head (or pump for the matter) are 19 ft-lbs. I use Loc-Tite on those but both have an o-ring (which provides most of the seal) so I'm not to keen on gronking the rail plug.
3. I'm also replacing both HPOP gaskets. I know that the HPOP and reservoir mounting bolts are 18 ft-lbs (from Ziggy. in the tech sticky) but is there a spec for the cover bolts too? I know the gasket provides the seal but I'd like to make sure that the force is distributed evenly across the gasket (Sous isn't the only OCD person around).
Hopefully this fixes most to all my oil leaks (still have to tackle the oil cooler). The valley is covered (as well as the front of the reservoir) and there is a lot of weepage on the paper towel test. There are years of buildup everywhere and will take a few tries and several cases of Simple Green to see the metal again.
View 2 Replies
I read 18lbs for the water pump but it took a cheater bar (perhaps due to corrosion) to get the water pump lower elbow bolts off.
On reinstallation, what should the lower elbow bolts be torqued to? Checked the sticky (Ziggy's Torque Specs) but didn't see the specs for this item.
View 2 Replies
I wanted to know what happens when the injector hold down bolts are not torqued down to spec, what problems would arise and could it be a reason for somewhat hard starting?
View 1 Replies
