Ford 7.3L Power Stroke (1999-2003) :: F250 - Starting System Wiring Diagram?
Dec 28, 2015
I have a new to me 1999 F250 with the 7.3 engine. The previous owner installed a push button start to get around the ignition actuator being broke. Over the weekend I pulled the column and replaced the actuator but the truck will still not start with the key; with the push button it starts just fine. I'm not getting any power on the starter relay signal wire, so I suspect something in between the key and starter relay. I searched around a bit, but could not find a wiring diagram for a 1999 diesel super duty.
View 3 Replies
Advertisement
Where I can get a radio wiring diagram for 2003 F250 Crew Cab?
View 1 Replies
I can't find a wiring diagram for the UVCH pigtail anywhere. The one that came with the harness assumes the old one was still connected. My wires were burned through and I need to know what colors to wire in from the truck to the new harness so everything matches up.
View 9 Replies
I am looking at putting a couple small LEDs in the pinch weld area under the doors on the cab. I want to have them come on when I open up a door. Where is the best place to grab power from the door switch circuit for that? The passenger side I was thinking of grabbing it where it goes into the sleeve between the cab and the door, but on the drivers side there are a lot of things in the way to get to that point. Can I pick it up down in the door jamb area? Is there a wire going to the dome light there?
View 8 Replies
Got a 2002 7.3 f550 and the other morning it wouldn't go into high idle. Noticed my parking brake light was off. Messed with the switch and eventually jumped straight from the connector to ground... still no light. The light does illuminate with key on. I have tested the fuses. Where do I go from here? Looking for a wiring diagram....
View 14 Replies
Any pic or wiring diagram of the starter relay that is mounted to the fender. I'm trying to start the truck finally but it's just cranking and I think I might have mixed up the wiring. Is there supposed to be a constant hot at the glow plug relay when the ignition is off?
View 14 Replies
I am trying to add courtesy lights to the existing reflectors in the front doors of my supercab. I can't find a wiring diagram that shows where to connect the light sockets. 1999 F250 SD...
View 2 Replies
'99 F-250 7.3 PS 2WD Automatic 246,000 miles
Jumped in my truck a bit ago and it wouldn't start, although it is turning over. The "Wait to Start" light is not coming on and the Overdrive button on the shifter is lit up OFF and won't change with me pressing the button. I've checked all the fuses under hood and inside cab with multimeter and everything checks out ok.
Also, when it was raining last week I found that when I turned on my windshield wipers the truck would die. My solution to get home was to just flip it back & forth real quick every so often so I could see out the windshield.
View 11 Replies
My dad has a 99 F250 with a no start issue. Everything was starting and running fine one day. The next he gets a no start. Cranks fast and fine but wont fire up and start. He has a scangaugeII hooked up to it and his oil pressures and volts look fine. His tach moves when he is trying to start it. He checked the icp sensor and it had oil through it so he replaced it with a Ford part. Unplugged it and the scangauge pressure goes up but no start. He also replaced the ipr with a new Ford one just in case. He checked and is getting low pressure and high pressure oil. I am having him check the fuel heater fuse #22 to make sure it is not blown. He had the block heater plugged in all night along with a battery charger to make sure they are topped off as well. We have gone through a couple of the checklists on this site for a no start condition but nothing has solved it yet. If you need any info off the scangauge let me know and I will post the exact readings. I think he is sitting at about 200k on the motor. No major issues or problems until now. He is currently also pulling the ICM to check it out as well. No codes are being thrown.
View 6 Replies
I have a 1995 f-250 7.3 liter diesel engine. Truck starts fine and runs good for a while and then it will stall. I pull over and after a couple of attempts it will start and run fine for a while. I have changed the fuel filter and put fresh fuel in but it still stalls.
View 7 Replies
2001 F250 7.3l 294k miles
Ok so truck has always had difficulty starting cold since I got it about 12k miles ago. Replaced glow plugs, that made things slightly better but still no start unless temp gauge was in that first line above the C. Changed to Rotella, immediately after oil change starts better and at slightly colder temps.
Since getting the truck when you turn the ignition on you can hear a 'whistling' type noise which I believe is the fuel system pressurising. That used to last as long as the chimes did when you first turn the ignition on. More recently it lasts a lot longer.
Towed recently and had intermittent check engine light - believe this could be HPOP related, haven't checked codes yet as we're on vacation. No oil in the valley. But I do have a little oil carry over in the turbo intercooler pipes.
Truck slightly sluggish at setting off initially and then picks up reasonably well when not towing but my Dyno says I'm putting a bit more pedal to get the same performance from say two months ago
Pretty sure injectors haven't been changed since truck was new but can't be absolutely certain as there is no history. I was surmising this is probably both a HPOP and injector age issue but only from what I've found searching...
View 14 Replies
I have a 2001 F250 Crew Cab with Powerstroke. The dash lights are starting to go out one at a time. How do I get to and replace the bulbs?
View 14 Replies
Truck stalls out and cranks hard for 7-10 seconds before starting if I don't let it warm up adequately before I start driving. Transmission is hesitant to shift. Also, white smoke comes out exhaust if it's cold and I get in the throttle too much or if I hit 70+mph.
View 2 Replies
First, need a wiring diagram for the outputs on the back of the brake controller module? I want to check and see if there is a problem with the connection to the rheostat. I can activate the trailer brakes with the slider bar but not with the brakes.
Second, where I can get a new OEM controller that will replace my old one if I can't "Cypher it out"?
View 2 Replies
My truck didn't come with factory option aux switches. Can it be added, and is wiring present?
View 14 Replies
I need a wiring diagram for my 2000 F-350 power mirrors also to go along with the power window schematics that I posted before.
View 8 Replies
Where I can find a wiring diagram of the inside and outside lights on the 6.0s? I'm trying to wire up my running boars lights to my dome lights and tail lights but don't know the colors or locations of the wires. The tail lights wouldn't be as hard to find as the dome lights, what is the location and color of both.
View 14 Replies
Looking for the wiring diagram with colors for which port should be what wire for the obd2 connector for my early 99 f-250. I actually think it is obd 1 on our trucks but you get the idea. My truck doesn't have power to the plug I guess. I have a guy plug in a scanner to take a look at everything but he said the plug wouldn't power up his scanner. Just trying to get this fixed. Another question, if I buy a AE does that require the truck to power up the software or does it get powered my the laptop?
View 11 Replies
2013 F350 Lariat with the factory OEM rear view camera. I am replacing the tailgate with a 5th wheel tailgate for a few months and would like to still retain the convince of a rear view camera.
I have obtained a Ford camera harness to use as a jumper for a non OEM camera which comes with the standard basic RCA wiring which I plan to mount to the bottom of the 5th wheel tailgate.
My hope is to wire the camera direct to the Ford wire harness which is a 6 wire pigtail. Which wires on the camera mate to which wire on the trucks wire harness.
View 14 Replies
I need to connect a remote start stop for a bucket truck attachment to this new 2016 F550. Found everything except the ignition wiring harness diagram. Need to know what I can tie in to.
View 4 Replies
Working on putting this project back together and cant find my notes when I pulled it apart last year. Any schematic or picture of their brake lines from the master cylinder to the rabs or front brakes? Better yet, which port on the master cylinder goes to what axle?
View 9 Replies
