Ford 7.3L Power Stroke (1999-2003) :: F250 - Missing And Jerking - Code P0541 / P0640
Jan 16, 2017
1999 F250 7.3 .. The truck seems to idle fine and and runs smooth all the way up top cruising speed, but when it levels out at say 65mph then it starts missing and jumping. I can ease into the throttle a little and it smooths out up until it levels out again.
I have the Vgate Elm and Car Guage Pro and a couple of other apps and the only DTCs I'm getting anymore are:
P0541 Intake Air Heater Circuit Low
P0640 Intake Air Heater Control Circuit
But from what I've read, neither of those should cause this issue.
Buzz test sounds good.
Cylinder Contribution test throws code for #4 Cylinder
I'm trying to do everything possible before throwing an injector in it.
View 6 Replies
Advertisement
Air Intake Heater Plug Code Eliminator P0541
In conjunction with the AIH Delete Plug??
View 14 Replies
1994 f250 7.3 turbo problem.. runs great on the level.. Cruises 65 no problem.. We have an 8% grade coming from town and half way up it starts cutting out and sounds like a jack brake under the hood and loses power.. Once over the top it clears out and runs fine again.... I just changed the fuel filters but no luck... I have been wrenching on cars all my life but no diesels..
View 6 Replies
Just picked up a 99 F250 7.3 Stroker, it had sat for two years in a warehouse, the truck had just had reman injectors put in right before it was parked. We fired it up, and it was missing, and smoking a lot (light blue, almost white) I checked the oil filler cap, and no water on it, after it ran for a while, it stopped. Shut it down, went and got my trailer ready to load the truck, fired it up, and no smoke to speak of, by the time I got it to my trailer, still no smoke.
I revved it against the governor a few times, hoping to clear the miss (figured may have been trash, or a sticky injector from sitting so long) It is turned up pretty good, as it came with a Superchip Super Tuner. It seems to hit on all eight above 2500 RPM or so. Brought it home, and took it out on the road, it seems to only miss under 2500 RPM or so. I took of from a dead stop, then got on it hard at about 15 to 20 MPH, it took of nice, then all of a sudden, the tach started climbing like the trans was slipping, looked in the mirror, and the tires were smoking, guess they broke loose when the boost came in!
I let it idle and warm up for a good half hour and noticed a lot of pure white smoke coming from the exhaust, went back to it and it was steam, I took the oil filler cap off, and there was a lot of steam coming out of there, pulled the dipstick, more steam, I then noticed the degas bottle was low, I topped it off, and got in the truck, and revved it a few times, then held it at 2500 RPM for about a minute, It started blowing water out from under the degas bottle cap. I called the guy I got it from, and he did NOT put new injector sleeves in when he did the injectors, I don't see any oil in the water, but there is water getting on the oil filler cap now! Does it sound like a head gasket, or an injector sleeve?
View 7 Replies
I have a '99 F250 SD 7.3 & im going on a trip next weekend so I thought I'd pull the exhaust pressure sensor & clean the tube in an attempt to get better mileage. Found the sensor & unplugged it. Went to the manifold & started removing the tube when it fell off. 6" from the manifold it's broke & the rest is completely missing.
Autozone doesn't carry this tube so, how important is this sensor?
View 7 Replies
Recently I have had many problems with my 2000 7.3l .... The one I cant get rid of is the p1316 code. I have changed out the uvc harness and gasket with new ones, then removed valve cover's to double check connections again and they are fine. I am getting white smoke and the truck misses. I do not have a advanced reader for the codes just using my edge programmer. I have also disconnected the battery and cleared the code but it comes right back.
View 14 Replies
My truck is showing code p1277. The only time I really notice anything is cold mornings like we been this week. Low 50s. When I first start it in the morning the engine light goes on and off until the truck is completely warmed up. Could it be the injector going bad?
2003 f250 7.3 with 415000 miles. Stock injectors
View 2 Replies
But it starts. '99 F250 PS. Had code P1670, cleared it. No other codes. Started truck back up and ran KOER test with AE(which I'm not very good with). The code did not come back. It is hard to start plugged in cold or warmed up. I have WTS light and it goes out(glow plugs are original). RPMs are slow to come up (almost starts before it kicks in). Doesn't matter if fuel tank is full or not. Oil level is fine. Batteries are charged and check good. Starter checks out ok. Buzz test was ok. Now when I run KOER do I need to do anything other than hitting the initiate button?
View 10 Replies
I have a 2001 f250 7.3. Recently started this problem idling at 1000 Rpms when stopped completely and when I let off the gas pedal it idles real funny like it's fixing to run out of fuel. It does not do this all the time however. At times it runs great. I had my mechanic scan it and at first it was the exhaust pressure sensor. Replaced it and it ran fine for awhile and it started doing again. Took it back in to get re scanned and it was throwing a bad ICM code. Replaced this as well and I'm still having the same problem. Had it scanned again and it's not throwing any codes now. I have no check engine light on and as long as I'm on the gas pedal it runs great. It's just when I roll up to stop or when I'm stopped completely. Again it does not do it all the time.
View 9 Replies
Alright I have a 01 F250 with the 7.3L in it. Recently had the turbo rebuilt and all the surrounding gaskets changed as well as boots. All this was done around 1,000 miles ago. Runs great and I don't see/feel any issues, no white smoke anytime, little black when I turn up the tuner and really ride the thing but normal driving none. Problem is I have a pending P1247 code that after a few days will throw a CEL... I'm not sure what the problem is and have been searching the forum and people are mostly saying they get it but the boost drops or there isn't any at all and the truck my stall or bog down. I don't have any of those problems. Turbo spools up to whatever I want and I've never had it stall or bog or even get close... So what should I check? Also new to the site and diesels.
View 14 Replies
Just bought a 2002 F-250 4x4 Off-Road Crew Cab 7.3L and the airbag light is staying on. I have found out after the fact that the truck has been previously involved in a front end collision. The damage was to the passenger side front. I turn the ignition on, the airbag light will come on solid (just like all the rest, with the exception of the 4x4 and 4x4 low) then go out. Then it flashes slowly 2x then 5x, then goes out for a bit then repeats a few times before staying on. This tells me I am getting a code of 25. I have searched with no luck to narrow this issue down. Everything mechanically works, cruise, horn, etc. The only thing I can find wrong is when I engage the 4-wheel drive (floor shifter) the indicator lights do not illuminate in the instrument cluster. Neither the 4x4 nor the 4x4 low. I am unfamiliar with this truck, so I don't know where to began searching. I cant afford to take it to a dealer and I have children in the truck quite often, so I would like to remedy this very quickly.
View 9 Replies
About a year ago, my airbag indicator light threw a code 47. It did this for about two days, then it stopped. Fast forward to this weekend, and it started again. From what I can tell, it is the passenger side seat belt pretensioner. It could be a coincidence, but my daughter pulled the seat recline lever without anyone being in the seat, causing it to fly forward as if James Bond was ejecting someone through the windshield. The next time I started my truck, it was throwing the code. I tried to check to see if the plug was knocked loose during the ejection sequence. I thought the connector was under the passenger seat, but I don't see any wiring (the passenger seat is manual). My next guess was behind the glove box, but I'm not sure what I'm looking for.
My truck is a 2001 F250 4x4 Lariat.
View 2 Replies
Okay, I am having issues with a 1999 F250 XLT 7.3 with diablo programmer. I have searched and searched and have tried everything we could think of and it is a no go. The truck will crank, hesitate to start, start and die, other times it will only crank and not run at all. We can make it stay running by hitting the accelerator. The only code we were getting was the cps code, but that is suspected to be because of the excessive cranking and no start times. Previous to this issue getting this serious it would stall randomly, at idle, going down the road at constant speed, slowing down, or accelerating. We now have code P0231.
Through this we have tried:
IDM
(loaner) ECM
removing Diablo
3 CPS
shaving down CPS
Shimming CPS
IPR
Fuel pump
relay
fuel pump fuse
View 3 Replies
I have a 2006 F250 King Ranch 6.0. At approx 45-50 mph when holding accelerator steady, there is a slight jerking like the engine is missing like the old gassers used to do. What could cause this? Have a ScangaugeII and doesn't show anything out of the ordinary!
View 3 Replies
When I let off on the throttle the truck jerk forward a little. It does it some times when hitting the throttle too. I have changed u joints in the drive shaft. I noticed the carrier bearing has a little play (going to change it this weekend). But I wouldn't think that would cause this.
View 14 Replies
I bought this truck with a stock automatic transmission and 260k miles back in October expecting the transmission to be the first thing to go. Recently I had a transmission code, OD OFF light flashing, for the bad speed sensor which i got replaced. Then the OD OFF light started flashing after some hard driving when I would put into neutral or park so I took it back to the mechanic, Hanahan Truck and Auto in Sc. They looked into it and there wasn't any different code in the system but they noticed when you lay into it driving it slips some between 2nd and 3rd gears so that could cause the computer to put in a code.
They said usually a rebuild runs from $2k-2.5k and they also recommended a Jasper reman for roughly $2.8k which comes with a 100k mile 3yr warranty. So I figure replacing the transmission is probably the way to go. Any recommendations for a replacement. I've heard ATS and Sun Coast are decent options that I could build one. I'm looking to stay close to $3k. My truck is a 2000 F250 lariat 4x4 with 268k miles. I'm installing an S&B intake, 4" MBRP exhaust, and DP-Tuner's F6 chip when I get the transmission work done.
View 11 Replies
I have 2003 f250 7.3 automatic 181,000 miles completely stock. Never had chip,tuner or anything on it. I am second owner and got it when it had 70,000 miles on it. Ok here we go I live on top of a mountain and soon as i start up the mountain or any steep hill, or pull or tow something my service engine light pops on. First time it came on I took it to diesel shop they hooked it up to scanner and said it was code p1211 said icp sensor was bad so they put new one on. Couple days later light started popping back on so i decided to order a auto ingenuity after doing some research.
Hooked up to truck started up mountain while scanning at wot light pops on code p1211 and think it was live data I remember seeing icp pressure at 1922 and duty cycle at 63% i was trying to drive and read it at same time and my lap top went dead. What does this reading mean 1922 pressure/ at 63% cycle done little research but dont really understand. Year and half ago replaced all orings on all injectors, new rebuilt hpop pump. New ipr valve, glow plugs, past month 2 different icp sensor new,and new ipr valve new pig tails on both and light still popping on.
View 4 Replies
I have had a problem where truck would start jerking and sputtering in a certain town at low speeds. Today it happened in a new place. Barely got it to start back up. Was running rough after the puff of black smoke. Its stranded at a gas station. Recently replaced my sending unit. Was running good. Clean gas tank. Fuel lines tight. Where should I begin? I have an ICP sensor in the glove box. Truck wouldn't start.
View 8 Replies
2000 F250, 7.3, 170K, running rough, knocking loudly, missing, shaking, no power to get up driveway, intermittent, no codes spit out at all. No smoke visible, no leaks visible, New fuel filter, air filter, update cam sensor, new fuel rail lift pump, new uvc harness, new glow plug relay.
View 14 Replies
My 02 excursion is missing at idle and jars the whole truck around going approx 50mph feels like good amount of power loss but still pushing 30psi boost, just got autoenginuity all injectors buzz fine on the test, contribution test show balance fault in cylinders 1&8, should I look for o-rings to be bad, uvch, cups cracked or what ----- turbo fine, hpop great condition, new IPR, new fuel pump and hutch mod, about. 250k miles on truck nothing else major showed up on ae.
View 5 Replies
I have a 2002 7.3l with 229k miles. So I am having a big problem now missing oil! My reservoir is empty and my dip stick is reading low, and i just put 16 quarts in yesterday with the new filter! im having a long start issue obviously because i don't have any oil supply! just drove the truck today, ran great been having this issue for the past week. here are the details. i came up from Texas after installing joeys t500 pump, when i arrived to California there was oil everywhere! my pump that joey rebuilt had an issue so he sent me another and bam! runs great no probs, now after about to weeks and about 15 degree temp drop i get hard starting. first time instead of a 2 second start up it took 9 seconds, now it takes anywhere from 9-20 seconds to start! so after my drive today i let it sit for about 3 hours seeing if maybe i had air in the lines from the res not being full, well now i cant get a start at all my res is empty and my dipstick shows little oil, i just replaced the icp. ipr, and eot when i put the first pump in, could this be the lpop?
View 14 Replies
