Ford 7.3L Power Stroke (1999-2003) :: F250 - Code P1211 - Service Engine Light Pops Up Going Steep Hill
Sep 26, 2015
I have 2003 f250 7.3 automatic 181,000 miles completely stock. Never had chip,tuner or anything on it. I am second owner and got it when it had 70,000 miles on it. Ok here we go I live on top of a mountain and soon as i start up the mountain or any steep hill, or pull or tow something my service engine light pops on. First time it came on I took it to diesel shop they hooked it up to scanner and said it was code p1211 said icp sensor was bad so they put new one on. Couple days later light started popping back on so i decided to order a auto ingenuity after doing some research.
Hooked up to truck started up mountain while scanning at wot light pops on code p1211 and think it was live data I remember seeing icp pressure at 1922 and duty cycle at 63% i was trying to drive and read it at same time and my lap top went dead. What does this reading mean 1922 pressure/ at 63% cycle done little research but dont really understand. Year and half ago replaced all orings on all injectors, new rebuilt hpop pump. New ipr valve, glow plugs, past month 2 different icp sensor new,and new ipr valve new pig tails on both and light still popping on.
View 4 Replies
Advertisement
I was on the way back from the weekend trip and got a service engine soon light. I didn't notice any lack of power, rough idle or hard starting cold or hot. So we pushed on home. I checked the codes and it is the P1211.
Doing some research it seems the ICP is not as expected so I hooked up my phone with the Torque app and the IPR and ICP seem to be close to normal at idle and running. I din't see any high IPR %.
At idle the IPR was around 15.5 cold and 10.1 after a short run to the store and back when it warmed up a bit. ICP was around 690-720 cold and 470-490 when i got back.
Does that seem like normal readings? I cleared the codes and the CEL comes back on right away after starting the truck. I do have a TS performance chip that I will take out and see if that could be causing any problems. What else should I be looking into?
View 14 Replies
Was climbing a steep hill at 35 mph just before truck down shifted to 2nd, I was hearing a pinging sound. Sounded like only I cylinder was doing so. What it could be. I am currently running a 1/4 tank of Fppf fuel injector cleaner. Is this a injector noise. No knocking just a slight pinging.
View 1 Replies
I had a p1211 code when I first got Torque Pro hooked up. I figured it was just because I'd done a couple WOT runs and the HPOP just can't quite keep up with the injectors. I was told this might happen when I ordered the injectors from Gear head. I also noticed that my ICP peaked at around 3600 during one of these runs. I don't have it logged, but I'm certain it was up that high.
The code hasn't returned, but I haven't been running it too hard either. I don't quite know what to make of the ICPs actually being that high. From looking at a bunch of Rich's graphs his doesn't really get past 2800 or 2900. Is this an incorrect reading? Do I need to worry about anything?
View 6 Replies
My wife returned home and stated that my excursion stopped running twice while she was driving it. She said both times were as she was letting off the throttle coming downhill an off ramp. Both times it fired right up and drove away fine.
I pulled the codes using torque app and it showed a p1211. Unfortunately I had just screwed up my gauge settings so I really didn't have any gauges set up so I couldn't use it. (It's for the 6.0 anyway).
After some Internet searching I am guessing it's an issue with the icp or ipr. How do I tell which one to replace? Truck does have a dp tuner normally set to 80 economy tune.
View 11 Replies
My truck gave me the p1211 code today. I'm Trying to use dash command to get more info. What should I be monitoring and how do I do it? I'm not familiar with these apps at all?
View 3 Replies
I have posted a pic of a smoke issue I am having while pulling.
I just pulled a 10,000 lb trailer up a few 7% grades at 8-10,000 ft and the best I could do was 40-45 mph at 6mpg. Every hill would set a P1211 and when the truck downshifted to 3rd the smoke would go away for the most part.
Truck is 100% stock and pulls the same as my F350 with 3.73 gears but smokes a lot more.
The smoke is kind of annoying and performance seems sluggish especially given the 4.88 gearing. Where to start?
Has new ipr, hpop, icp, fuel filter, air filter, fresh 5w40 mobil 1.
View 14 Replies
I have a 2003 F250CC 7.3 with 200,000 miles on it. I just purchased this truck about a month ago. My question is it blows black smoke. A little at idle but mostly when you give it any pedal. I have replaced all of the injector o rings and that didn't make a difference. Then I had it tested and it failed a CCT test on #2 cylinder. I have an injector to put in it, but am curious to find out if 1 bad injector would be enough to make it smoke all the time. I keep getting P1211 ICP pressure above desired. I had a friend of mine who used to work at a ford garage take a look at it with his computer and he said that everything looks good other than the CCT test.
View 14 Replies
my 2003 f-250 4x4 6.0 engine service light stays on all the time (for about 2 weeks now) it has 33,323 miles on it. it is running fine-no problems yet. no codes are showing up on a diagnostic test. What is going on?
View 10 Replies
I just bought a 2003 F250 from a used dealer. Unfortunately the service engine light keeps popping on and putting out the code P0401, I have replaced the EGR, cleaned the inside, and cleared the code. However it continues to keep popping up and then it will turn off after a couple of days. I mostly drive in the city and the code generally only pops on when I drive on the highway. I have also noticed a lack or delay of power, when I really hit it hard, I think its because the computer is keeping the egr valve open. What it could be?
View 3 Replies
So i replaced the faulty injector and the truck starts up great and runs great. The only issue is that now when i accelerate, the SES light comes on until i let it up a little. If i am at cruising speed or just a steady speed the light goes off. I havent checked for codes yet because the light didnt stay on. I have AE and know how to use most of it. Is there something i should be looking at? Could it have something to do with the Blue/Gray CPS i installed or maybe there could still be an air bubble in the oil rail from when i drained the rail ? I have a DP tuner and stage-1 injectors. Regardless it sure is nice to have my truck back out on the road. It was a horrible 3 weeks without it.
View 14 Replies
Light came on a few days ago. 2000 exc with 7.3 diesel the mileage report said 155000. Took it to Autozone a hour ago and these are the codes: P0683, P0676 and P1670.
View 14 Replies
Truck started losing power then service engine light came on, drove about another mile then it just stalled ( almost home lees than a 1/4 mile). Got out open hood oil everywhere on top of motor. Looked under truck and oil all over the road. Looked back where I was driving a line of oil as far an I could see. Checked oil barely any on stick. Where should I start hpop or plug?
View 7 Replies
The SES light in my 2001 7.3 came on about a month ago while I was towing a light trailer in the SoCal mountains. When I got home I spent about 2 weeks replacing the injector o-rings and glow plugs. I discovered while I was in there that the head bolts on the driver's side where loose. I retorqued them to spec.
Both batteries were disconnected for the 2 weeks. When I started the truck the SES light was still on.
My Torque Pro app isn't showing any error codes, and is reading live data correctly. (I didn't have the app when the light first came on; I only purchased it after I finished the repairs). Am I missing something? Is the SES light not necessarily connected to fault codes? If so, wouldn't it reset after 2 weeks with the batteries disconnected?
View 5 Replies
I have a 2001 F350 and my service engine soon light came on. For a while it went on and off and every time it came on the engine ran rough and I lost some power. I pulled the valve covers and checked the UCVH and everything was fine that I can tell I even made the shims out of quarters and put them in. After putting it all back together its still doing the same thing.
View 1 Replies
I was coasting down a steep hill yesterday when the CEL came on. I pulled the code this morning and got code P0174, system too lean bank 2.
I cleared the code. Should I just wait to see if it happens again? The truck is running great. There is no sign of a problem. BTW, it's 99 F150 5.4.
View 14 Replies
On my 7.3 super cab, I changed the fuel filter last Friday and now on cold start the service engine soon light comes on for a couple minutes (approximately) on a cold start. No other issues. Tried scanning with my scan gauge 2 and no codes. (of coarse I think that thing is a joke for scanning). Not sure if this means anything, but last week before I changed the filter I thought I smelled diesel fuel on a couple different occasions. If I actually did it may not even be related.
View 2 Replies
So about 3-4 times per day, my truck will accelerate very quickly with the slightest touch of the gas pedal, then followed by the service engine soon light...I checked for any codes to see what I may need to fix, but no codes are found.
What this could be? I am also having issues to where I a few times per day I have to put my truck in neutral to get it to start instead of in park...could the two be related?
View 8 Replies
Just bought a 2002 F-250 4x4 Off-Road Crew Cab 7.3L and the airbag light is staying on. I have found out after the fact that the truck has been previously involved in a front end collision. The damage was to the passenger side front. I turn the ignition on, the airbag light will come on solid (just like all the rest, with the exception of the 4x4 and 4x4 low) then go out. Then it flashes slowly 2x then 5x, then goes out for a bit then repeats a few times before staying on. This tells me I am getting a code of 25. I have searched with no luck to narrow this issue down. Everything mechanically works, cruise, horn, etc. The only thing I can find wrong is when I engage the 4-wheel drive (floor shifter) the indicator lights do not illuminate in the instrument cluster. Neither the 4x4 nor the 4x4 low. I am unfamiliar with this truck, so I don't know where to began searching. I cant afford to take it to a dealer and I have children in the truck quite often, so I would like to remedy this very quickly.
View 9 Replies
About a year ago, my airbag indicator light threw a code 47. It did this for about two days, then it stopped. Fast forward to this weekend, and it started again. From what I can tell, it is the passenger side seat belt pretensioner. It could be a coincidence, but my daughter pulled the seat recline lever without anyone being in the seat, causing it to fly forward as if James Bond was ejecting someone through the windshield. The next time I started my truck, it was throwing the code. I tried to check to see if the plug was knocked loose during the ejection sequence. I thought the connector was under the passenger seat, but I don't see any wiring (the passenger seat is manual). My next guess was behind the glove box, but I'm not sure what I'm looking for.
My truck is a 2001 F250 4x4 Lariat.
View 2 Replies
I bought this truck with a stock automatic transmission and 260k miles back in October expecting the transmission to be the first thing to go. Recently I had a transmission code, OD OFF light flashing, for the bad speed sensor which i got replaced. Then the OD OFF light started flashing after some hard driving when I would put into neutral or park so I took it back to the mechanic, Hanahan Truck and Auto in Sc. They looked into it and there wasn't any different code in the system but they noticed when you lay into it driving it slips some between 2nd and 3rd gears so that could cause the computer to put in a code.
They said usually a rebuild runs from $2k-2.5k and they also recommended a Jasper reman for roughly $2.8k which comes with a 100k mile 3yr warranty. So I figure replacing the transmission is probably the way to go. Any recommendations for a replacement. I've heard ATS and Sun Coast are decent options that I could build one. I'm looking to stay close to $3k. My truck is a 2000 F250 lariat 4x4 with 268k miles. I'm installing an S&B intake, 4" MBRP exhaust, and DP-Tuner's F6 chip when I get the transmission work done.
View 11 Replies
