Ford 7.3L Power Stroke (1999-2003) :: Exhaust Manifold Removal - 1 Bolt Stuck?
Jan 10, 2016
I managed to get the drivers side exhaust manifold and all of its bolts off no problem. On the passenger side I had 1 bolt head that was already broken and I have only 1 other that is still holding on for dear life. I've been soaking it in aerokroil for awhile now and no luck. I tried some PB blaster today because I am willing to try anything. I also tried heating up the bolt with a torch and some map gas but not sure if I am heating it up enough or not. Anyways, everything else has been going great, got the uppipes off and the valley, turbo and pedestal all cleaned up good. Just need to get the last whole bolt and broken bolt out so I can install the new manifolds. What I should try to remove the last 2 bolts. How hot should I get the bolt when trying to remove it? Or should I be heating the engine block?
View 12 Replies
Advertisement
So I received my International bellowed up pipes from Riffraff and I figure I will start soaking all of the bolts with some aerokroil before I get started on monday and I see the very last bolt head near the up pipe is gone. The bolt is there but the head is gone and you can definitely see soot buildup everywhere near it. I don't know if I should order a new manifold for the passenger side and new bolts, order a driver and passenger side manifold and new bolts, or just order one set of new bolts and try to get take the passenger side manifold off and replace the one broken bolt.
View 4 Replies
Well i had an exhaust leak on this F250 and so I started torquing the bolts on the manifold to the head. (45 ft.lbs) A couple were very loose so I was thinking "Great, this may fix my problem!"
My first mistake was probably the Harbor Freight Tools torque wrench.
I am on the driver side, second from the rear and then bang! I see a gaping hole where the bolt used to be. Bolt on the floor. I cant see up in the hole to the head, I think it broke flush with the head.
View 14 Replies
I have a 1999 ford f150 4.6 engine and it has an exhaust leak but wondering what is the procedure to remove a broken bolt and the rest of the bolts on the manifold
View 2 Replies
I own a e1999 Ford F350 7.3 4x4 with a Garrett GTP38R turbo. I have been having issues with very little power and pulled an CEL of P0221. I know it's for the APS and have been trying to trouble shoot it as a new APS has not fixed the problem. However, while working on that I just noticed an oil leak appear. I tracked it down and can visibly see it leaking out the top of the passenger side exhaust manifold in two places. It is seeping out the top. Is oil supposed to even be running through here like that?
I recently replaced my up pipes with the newer style bellowed ones. While I had the turbo off I replaced all the o-rings top and bottom and did the EBPV delete on the pedestal. I have been having very little power and cannot the truck over 5-10 MPH and stays at low RPM's so I originally thought it was the leaky up pipes. Those were fixed along with fuel pressure checks which came back good. I then pulled the P0221 code finally. While I had the turbo off I inspected it and it did spin freely and had no side to side play in it.
What was unusual to me was there was a small pooling of oil in the turbo when I took it off. I know the CCV goes through here so some oil is normal. Also, when I was diagnosing the up pipe leak I could see a small amount of oil spraying out the blown donut gasket along with the exhaust gases. I don't think that is normal.
Is there an internal seal in the turbo that can go bad causing oil to spill into my exhaust and possibly leak at the exhaust manifold? Or do I have an internal oil leak from somewhere else?
View 14 Replies
Just bought a 03, the seller showed me a exhaust leak. I found a bolt broken off, flush with the head. Looked at the passenger side when I got home, that side leaks too, and found one broken off bolt there too. Question, are these easy to do? As in, I have extracted broken bolts before, but they where on my V10 and I could just weld nuts to them and they came right out.
View 14 Replies
The bolt that holds the dipstick on the valve cover. i have tried for ever to get this thing off. soaked it , got a skinny wrench on the nut underneath but think it might be stripped (1/2 inch grinded out a little). going to try and get a set of skinny wrenches tomorrow , mine bent. tried vise grips on top of the bolt and put a box wrench on the nut , and gave it my all. The damn thing won't budge.
Also, any tips on the rest of the valve cover bolts. I had to remove some from inside the fender well but barely got to them. My question is not getting these out but getting them back in. And how the heck to you torque these things??? The bolt i mentioned above is creating problem, and I only have so much time
View 8 Replies
I had a fuel starvation problem because Ford painted the inside of the fuel tank and the paint was coming off and clogging the filters and because I foolishly drove it I now have white smoke spewing out of the tail pipe and an engine miss.
I also explained that I thought that the white smoke did not smell sweet like antifreeze, but rather like diesel. (Hoping that a head gasket replacement is not required.)
I am in the middle of doing the Hutch Mod with frame-mounted Racor PS120-2 jar-type screen pre-pump filter and shortening my previous Harpoon Mod and paint stripping and powerwashing the inside of my tank. Next I plan to move on toward the engine issue.
This evening I was under the van with a flashlight and I noticed that there was a black liquid of some sort at the driver's side exhaust manifold where it joins the up-pipe. At first I was afraid to touch it fearing that it would be carbon-sooted water, but it felt and tasted like carbon-sooted diesel.
And since I haven't started the engine in two weeks and it has been routinely near or over 100F in Sacramento, water would have likely evaporated days ago.
Does it make sense if the fuel starvation problem caused an injector nozzle or its cup to crack or to stick open or to otherwise spew unburnt fuel into the exhaust manifold which would cause the white smoke? Obviously, the unburnt fuel must get from the affected cylinder(s) to the tail pipe somehow, which likely means out the exhaust valve, through the exhaust manifold to the up-pipe and through the turbo to the exhaust pipe and finally to the tail pipe.
See pictures at my CP. I can't figure out how to attach them or put them inline here because it still says I can't do attachments.
What is my next move? Remove the driver's side valve cover? If so, what should I look for, etc.?
2002 E350 extended body van 7.3 diesel auto trans converted to 4x4 (bought new)
View 14 Replies
I just finished installing a new turbo (shaft play and lots of oil in the compressor side), RR up-pipes, and T500 (250k and once had a very long crank to get the ICP up to start).
Anyway, except for another exhaust leak at the pass side up-pipe to manifold, it seemed to run okay but with lots of white smoke. I only have about 50 miles after the install, when it suddenly starting surging and made a lot of loud knocking noises. This then went away and came back again rather quickly. I was close to home, so I made back under power. I also received the two codes listed. My IPR is original, but two summers ago I installed the IPR re-seal kit. Everything on the IPR looked good when it came off for the T500.
After reading around, I saw that low fuel pressure / air in fuel can cause problems. I connected a pressure gauge to the pre-filter port on the filter housing, and got 40psi at idle. I then took a diesel shower and blew out the fuel line into the tank. After re-connecting it, the fuel pressure stayed the same but the engines idles much better, but still has blue smoke. It's the original fuel pump (to me anyway) and original fuel line connections.
I have about 3/4 tank, and no place to put it, so I'd need to run it out for the Hutch mod, or least to get in there and inspect. Would eliminating the Ford connections at the pump be worthwhile for now, and is 40psi at idle adequate? Wondering if it's time for a fuel pump?
View 14 Replies
I got a 08 ford f450 sd in the shop with a cracked abd broken bolt in the driver's side exhaust manifold, any tips tricks on getting it out,I have everything loose but I can't for the life of me get the egr cooler out of the way to access the top bolts to the manifold so I can replace the manifold, or a link to a service manual would be great.
View 3 Replies
This is for a Pontiac Vibe. I broke one of the bolts that connects the exhaust pipe to the exhaust manifold. Need to get some type of nut/bolt/spring that I could use to fix it. The bolt is sticking out of the flange about 3/4" if I had a long nut to screw onto that?...........
View 6 Replies
Ive got a 89 Ford F250 four wheel drive with a 460. Ive had an exhaust leak coming from the driver side, i already installed new manifold gaskets but just the driver side i could still hear a leak but on one of the exhaust ports towards the front there's a stripped bolt, is there any kind of tool of some sort were i can extract that. i barely have room with the power steering hose and steering shaft in the way.
View 3 Replies
So I was in the process of doing a turbo swap to the borg warner sxe366 and the freeze plug that plugs the old mechanical fuel pump in the valley had to be removed well needless to say, it as well as the safety bolt I had attached to it fell into the motor, seperatly. I'm already getting the motor ready to be pulled but what are the odds that they made it to the oil pan or if they didn't any way to make them fall out?
View 10 Replies
I can't get my exhaust manifold bolts off. They are in bad shape. The 10mm is too loose and 3/8 just rounds. I have had the torches on them too! Can the bolts be cut off with a torch?? Haven't broken any. Can't get the bolt heads to move. It's an 04, original manifolds. I am working the driver's side. I can't figure this one out. How to get this manifold off?
View 4 Replies
How difficult is it to change the passenger exhaust manifold? I have just finished replacing the left exhaust manifold. The biggest issue was rusted fasteners and inexperience. Have torches. Any you tube videos show the left manifold being changed but not the right. I do not have a hoist and work in my driveway. Is the right side more difficult and should I leave it to someone with a hoist?
View 4 Replies
As part of my ongoing P1393 troubleshooting, I’ve found that I can’t get the main engine wire harness separated. The big connector by the driver’s side valve cover.
I’ve cranked and cranked in the correct direction, but the plug never separates. I tried a cordless impact wrench and it still doesn’t move. (Edit -- the bolt moves very freely, but it doesn't push out one side (e.g. like removing the PCM) I can't figure out how to separate the two sides.)
Any tips on how to get it separated? Can I cut off the bolt head to get it separated?
View 14 Replies
So I had recently developed a leak in the up pipes behind the collector. Big surprise, right?
Well, a 6-point socket was spinning on the collector bolts (probably from rust) so I decided to cut the manifold to up pipe bolts. Got the up pipes off/out. Well after and <acronym title="Manifold Absolute Pressure">MAP</acronym> gas torch, I can't punch ANY of the bolts out.
There is little to no room to get to the bolts. (I have the down pipe removed.) At this point I'll try a few more doses of hot wrench and PB Blaster, but if I have to do the manifolds I'll just pull the engine, since chances are there will be at least one stuck bolt there, too. I really don't want to go that, but eventually I'll need to install my new oil pan anyway.
View 14 Replies
So ford is replacing 8 injectors for me and they found this. They are trying to tell me bad oil cooler but I do not believe it. What do you all think is the cause. I should also say that I had coolant in my drivers side exhaust manifold.
View 14 Replies
How common is it for the hpop to leak from the round piece behind the pump next to the drain bolt? Its on a 2000 f350 7.3.
View 12 Replies
So I tried to replace my thermostat and housing and the housing bolt snapped off. Ok so I tried to extract that bolt off and the extractor bolt snapped off inside. I am guessing it might just be easiest to replace the water pump now? I am pretty much at the end of my mechanical rope which is short anyhow.
View 6 Replies
I am replacing the turbo on my 2005 f350 6.0. I have the passenger side mounting bolt and the rear mounting bolt out, but cannot get the driver side bolt to budge. I have sprayed it with WD40 and PB Blaster and tried a breaker bar. No luck breaking it loose. I am afraid I might round off the head even though I am using a 6 point socket.
View 12 Replies
