Ford 7.3L Power Stroke (1999-2003) :: Engine Died Suddenly / Turns Over But Won't Fire
Sep 12, 2015
I have a 99 F450 bucket truck. I was up in the bucket when the engine died suddenly. It turns over but won't fire. I have no dash warning lights now either but everything else seems to be working. Lights, radio, annoying beeping sound from the key left in the ignition, etc. There are roughly 5 or 6 fuses in the panel to the lower left of the steering column that don't have power to them. Are they all supposed to have power when the ignition is on? I checked the fuse panel under the hood and all of the fuses that have 12V to them are good. There are a few small ones that don't have power to them but I don't think they do all the time.
View 9 Replies
Advertisement
While driving my 99 F350 7.3 it died and I was lucky enough to coast home. No WTS light, no tach movement when cranking, no fuel pump, no CEL, Cranks great but no smoke or fire. New CPS & PCM still no lights or tach. Moved relays checked all fuses. WTF is wrong?
View 14 Replies
I am a cummins owner who just got a 2002 7.3 last week. It drove great for 200 miles then suddenly died last night going 60 mph. It sat overnight then started up and drove 10 miles then died again. I changed the cps and still no start. I changed the oil and let it sit overnight and it started this morning and idled for 5 minutes then died again. I have tried unplugging the ipc and still same no start situation. I plan to check the hpop level today to verify it is full. I also checked the nut on the ipr and it's electrical connection.
I am just a shade tree at best and would love some direction on where to look. I don't have any scan equipment to check pressures. Am I correct in thinking it is a bad ipr?
View 13 Replies
I have a 2001 f350 dually diesel, I was driving it with no problem and all of the Sudden it die when I was checking the problem I not that the fuse for the diesel pump was blown immediately I replaced it and as soon I turn the key on it blew it right away I fol the wires from the pump to the fuse box and there is no wires grounding so maybe I can get a little bit of info to find the source of the problem
View 1 Replies
I replaced my starter with a new one from car quest yesterday, it was starting to turn the engine over slow. I checked the batteries, they were fine, so went for a new starter. After installing, the new starter turned fast and fine, started the truck ok, but I noticed a fast clicking sound from under the dash. Ran it home and tried to start it up this morning, turns over fast, the clicking sound is still coming from under the dash, but the engine won't fire. Just turns over. When it's turning over the check engine (and all the other dash) lights flash.
View 3 Replies
This morning, I started my truck to go somewhere and less than a minute into my drive, the engine suddenly died. I tried cranking it again to which it started but less than a second later it quit again. That's when I noticed my FMP on my SGII was at 0v. When I got it back into a parking spot, I pulled the FICM and tested the connectors as well as the relays and they all were normal.
I decided I will be pulling the FICM again tomorrow and I will be sending it back to FICM repair.com for them to look at as I got a new one from them about 8 months ago. However if it is in case the wiring harness, where is a good place to look. I don't think it is the wiring harness as it seems to have voltage at the connectors.
Also this may be related but earlier this week, my Scangauge froze and I unplugged it and plugged it back in and it didn't connect to the PCM until I reset the SGII to factory settings. I wonder if this is related?
View 14 Replies
I have a 2000 F350 7.3 213,000 miles. Manual tranny, 2wd. It is my daily driver.
No issues until 2 weeks ago I pulled out and began shift gears when the engine died and I completely lose pedal. The engine does not shut off it goes to idle and the lights and power are fine but I quickly lose acceleration. After a couple seconds and a few pumps on the pedal it comes back. The problem is intermittant. Until yesterday it was only in the morning but then happened on the way home from work. Thinking ti was water in the fuel I used an additive to cure the water.
I changed the fuel filter just after I bought it in April of this year. I know there is a Injector Pressure Sensor that could be the culprit. EGR?
View 14 Replies
I was driving from my house the other day when the engine suddenly cut out and the dash went blank. there was no warning, it was like someone pulled the plug.
-When I turn the key to the first position (Acc) all the accessories work as normal. the lights, radio, windows, ect all work like normal.
-When I turn the key to the second position (run) nothing changes. no gauges, no dash lights, warning lights, and no (wait to start) squiggly line. only thing I hear is the high pressure pump on the engine cycle.
In the third position (start) the truck will turn over but will not start.
View 2 Replies
Yesterday my truck began to give me some problems starting. The engine turns over just a couple of times then it sounds like the starter disengages and winds up. it took multiple attempts but it finally fired up. Does this sound like the starter or could it possibly be the starter relay?
2002 F350 CCLB Lariat 7.3
View 7 Replies
So I've had my 2003 F-250 power stroke 6.0 for over a year now and replaced the oil with AMS oil which is good for 50,000 miles to a year as well as the oil filter which is guaranteed the same thing. I've only put 5,000 miles on it since I've owned it and made sure to let the engine heat up before going anywhere as well. Recently my engine bogged down and then had problems starting I was able to limp the last 2 miles to work but haven't been able to get it running since.
I replaced the camshaft position sensor and it fired up but once it was running it the rpm gauge dropped below 1000 RPMs it would stall out. Before it didn't have any smoke coming from the engine compartment however now when it starts it does. Is this because there's oil the possibly leaked onto something or fuel? What do I or should I look at to get it fixed?
View 6 Replies
Got up yesterday and the truck would start. Turns over just fine, but won't fire. Checked codes and got p0403, p0404, and p0405; all egr related issues.
I'm going to pull the egr and clean it, but my question is, would these codes cause a no start? I haven't had any issues with performance that I read are normally happening when people get these codes. Just wondering if I may have another issue along with the egr problems.
View 11 Replies
Friend's 2000 7.3 wont start, just crank and crank tried to fire but nothing in the cold leave it plugged in and it starts leave it in a shop over night and it starts with a shot of either, he is a truck driver and the truck will sometimes sits for 6 weeks at a time this time 2 weeks before I touched it. He wanted me to install a fuel pump so I did and started the following:
Cracked fuel lines to see if I had fuel psi at both heads
I tested glowplugs they all read at 0.3 on all 8
I have power to harness as the same at both sides of the relay
RPM tach jumps
Oil psi gauge rises
Using my phone I can read hpop and 2000 at cranking (how accurate that is im not 100% sure)
All fuses good
View 7 Replies
E99 zf6 180k. Ts 6 position and 6637. Just found d out the oil was 25000 miles old and changed it. 400 mile trip followed by a few days in town with no problems. Shut it off warm and it won't refire. Takes 3 loooong cranks. Few minutes later it restarts hard but not as hard. Head out for a few hundred mile trip and it's running fine except all of a sudden "bucks" a few times within a couple hour window. I took data during the trip and never saw anything strange. Today a cold start, around town driving, and warm restart were all normal.
My thoughts are to
1. Verify steady fuel pressure (I only have a temporary gauge setup)
2. Check the fuel filter for oil.
3. Pull the valve covers to look for injector oil leaks.
#3, though, I dunno if it's worth it. Perdels look fine and icp seems to be about the same as it always has.
View 6 Replies
My dad has a 99 F250 with a no start issue. Everything was starting and running fine one day. The next he gets a no start. Cranks fast and fine but wont fire up and start. He has a scangaugeII hooked up to it and his oil pressures and volts look fine. His tach moves when he is trying to start it. He checked the icp sensor and it had oil through it so he replaced it with a Ford part. Unplugged it and the scangauge pressure goes up but no start. He also replaced the ipr with a new Ford one just in case. He checked and is getting low pressure and high pressure oil. I am having him check the fuel heater fuse #22 to make sure it is not blown. He had the block heater plugged in all night along with a battery charger to make sure they are topped off as well. We have gone through a couple of the checklists on this site for a no start condition but nothing has solved it yet. If you need any info off the scangauge let me know and I will post the exact readings. I think he is sitting at about 200k on the motor. No major issues or problems until now. He is currently also pulling the ICM to check it out as well. No codes are being thrown.
View 6 Replies
I am having trouble getting my 2000 7.3 (200k) to start on the colder mornings. It will crank over fast, but won't start without a lot of tries. Today it took 6 pre-heats and cranks, but on others (and colder days) it has started easier. It does seem to be getting worse though.
I have replaced the glow plug relay recently so it *shouldn't* be that unless the replacement is fried. Starts fine the rest of the day and drives fine, but not in the cooler am (it was about 34 this morning). I also tested the batteries yesterday and while they aren't new, they tested okay.
Also, I read (briefly) about the CPS, but forgot to watch the tach this morning, but did notice it is pushing smoke out when turning over.
View 12 Replies
2002 7.3 PS TD.
Lately sometimes when I get in and start the truck all is well. Then the next time it will spin like a top, but not fire. New batteries. Then it will fire right up. It may go a few weeks, or days, then it happens again. Temperature does not seem to be a factor. It also doesn't matter if the engine is hot or cold. Once when rounding a corner at low speed, it just died, then started right up.
I recently changed the fuel and air filters. I think the glow plugs are getting old. In cool weather I turn the key on for about 1 min. before cranking. I have 110,000 on the engine with all original parts.
View 7 Replies
2002 7.3 Power Stroke... I bought the truck about 4 months ago and I absolutely love it but over the last few weeks is has been acting funny at times, it doesn't do it all the time but it has been getting progressively worse, ill drive the truck all day and no problems when I shut it off and go to start it again it just cranks but won't fire.
* Batteries are charged and in good condition, oil is a little dirty but full, I have no codes or check engine light on, and my wait to start light seems to be working fine!
* If I supply a fuel source(starting fluid) the truck will fire but not stay running
* And let it sit for 15 to 45 minutes fires right up like there was never an issue.
* There are no blown fuses
View 6 Replies
I just replaced my up pipes, turbo pedestal O-ring, ICP, IPR, New O-rings in all my injectors and torqued to spec, new glow plugs, glow plug relay, oil loom wiring harness, new O-rings on oil cooler, oil filter, oil, and antifreeze. I have tried and tried on upwards of 75 or so time to get it to turn over. A little white smoke came out and it sounded like it wanted to fire up, but only a few times.
I have good batteries and a charger on it, 3-4 tries in 5-10 second bursts or longer if it doesn't lose power every 30 -hr. oil is in HPOP too. just found out my block heater is dead, but I shouldn't need it now. Tach moves a little when I crank it but only when my oil pressure gauge hits half way and that about the time it wants to start and starts white smoking.
2001 F-350 7.3 auto 2wd 4dr longbed 329,611 ml
View 14 Replies
Owning a 2001 F250 Extended cab with a 7.3 I have not had a lot of questions to ask fortunately.
My truck has spent a lot more time sitting than running lately and when I went to start it the other day it cranked fine but would not fire. Quick read on this forum and the first thing I found was how if the fuel solenoid had less than 10.8 volts when cranking it would not start.
I went down and checked the battery voltage and it was at 12.1 volts no load. I put the battery charger on for about 10 hours (time to kill) and when I pulled the charger and cranked it over, started with no problem.
View 3 Replies
After 2yrs and 1mo, my DC power 270XP amp died. I put the almost 10 yr old factory alt back on and everything is good again, except for the glaring fact that I have a dead alternator. It is a month beyond warranty (of course).
Truck has been running great. Oil cooler, EGR bulletproof cooler, STC done in Dec at Ford due to high deltas. I have a small stereo - one 12" sub woofer, otherwise nothing that really stresses the electrical system. I did the "big three" with 1/0 copper - cost a fortune, saw no difference - but that could have been an issue for the alt.
I left a message today with etch support but did not get a call back. I hope they make good on this - I waited almost 4 mo's to get this thing and it was supposed to outlast my truck.
View 14 Replies
I just replaced the glow plugs, gpr, valve cover gasket and harness. When cooled down, cranks but won't fire. Smoke DOES come out the tailpipe. If I plug it in for awhile it fires right up. What else can I do or check?
View 5 Replies
