Ford 7.3L Power Stroke (1999-2003) :: Engine Cut Off While Running And Stopped Just Like Turned The Key Off
Feb 13, 2016
While stopped, engine running, in D, the engine cut off just like I turned the key off. I sat there for about thirty minutes and on the 7th or 8th try, the engine finally started. I drove it back to camp and thinking it might be the CPS, I swapped it out. Unfortunately it must be something else because I can't get it started anymore.
ICP and IPR are fairly new, but I unplugged the ICP and tried to start it anyway. It didn't choke out (like it was a fuel issue) but I checked the fuel bowl anyway and the pressure builds fine. I got it restarted once, so it can't be a fuse but I checked them all anyway.
Oil pressure builds to 780+ when cranking. Batteries still have plenty of cranking juice and without my AE, I'm frustrated beyond belief.
View 14 Replies
Advertisement
I was driving from my house the other day when the engine suddenly cut out and the dash went blank. there was no warning, it was like someone pulled the plug.
-When I turn the key to the first position (Acc) all the accessories work as normal. the lights, radio, windows, ect all work like normal.
-When I turn the key to the second position (run) nothing changes. no gauges, no dash lights, warning lights, and no (wait to start) squiggly line. only thing I hear is the high pressure pump on the engine cycle.
In the third position (start) the truck will turn over but will not start.
View 2 Replies
2003 CC 4x4 ... I am pretty sure I know what is going on, but I wanted to start a thread for when I confirm it. I am driving to work this AM and I hear the door ajar chime and I think to myself, uh oh...gauges all look good, there are no lights illuminated on the dash. I get to work and turn the truck off and my fan stays on. I think the ignition module is going bad. Either that, or my remote start is going on the fritz. I will update when I find out more.
View 3 Replies
My 2001 f250 7.3 was running then just shut off like I had turned the key off, While trying to start back up, the truck turns over fine but no fire. I also have no gauges, I tested both fuse boxes and the one under the hood I have power on all big fuses, including the PCM but some of the small ones I don't, No power to the PCM diode, either side, the fuse box inside the cab, I have half power, No power to the PCM fuse is their a fusible link somewhere?
I really can't see much down there. The truck did get into a accident in Oct, which created a problem with the ignition and not sure if that could be a problem? That problem is, when I turn the vehicle off, it would stay running for a few seconds. I ignored the problem cause it didn't hinder the vehicle any.
View 4 Replies
While pulling onto the highway and pulling pretty hard lost engine power all boost then engine truned off. Top of engine is covered in oil..... What happened?
View 11 Replies
I bought a 2002 body with a late 99 engine with lower miles a couple years ago. I knew it had an oil leak when I bought it. My other truck had a turbo pedestal leak. This truck has a small pedestal leak but it's not that much of an issue as there is little oil in the valley and next to nothing running down the back of the engine.
The other leak is getting worse. It has been leaking somewhere up front and coats the main steering arm off the steering box, the lower rad hose and the rest of the steering linkage. Last night after driving around 100 Kms I have oil running out from under the engine across the floor.
I changed the LPOP after thinking the front leak was from there. Unfortunately i don't think it was.
I am hoping it's the oil cooler and not the HPOP. One other thing is before yesterday's trip, I installed my homemade ccv mod off my other truck. I don't think the leak is coming from that either.
View 14 Replies
My engine suddenly stops while driving. There is no warning or loss of power, it just stops randomly after running fine for a while. After some time (might be minutes or hours) the engine turns on and runs fine.
I have no clue what it might be, I believe it might be an electrical problem affecting the diesel pump. The pump has a pair of cables coming in to a white plug at the pump's back, I disconnected them but the engine still runs.
View 6 Replies
2002 F350 7.3 PSD. 192k miles.
From my understanding, a CEL is supposed to illuminate each time you turn the ignition ON as part of normal startup procedure.
I figured the previous owner must have pulled out the bulb to hide the fact that the truck had a few "issues" before selling it, so today I pulled out the gauge cluster and it looked as if the CEL bulb was a tiny LED soldered directly into the gauge cluster itself. There were a few serviceable/removable bulbs for things like turn signal indicators, high-beam etc... but the CEL did not have a serviceable/removable bulb.
I've been driving this truck and working through it's "issues" and fixing things as I go, but it keeps throwing codes without the CEL illuminating. What's going on here?
I thought the check-engine-light was supposed to illuminate each time the ignition was turned on, and that it would come on each and every time the vehicle registered a fault code in the ECU/PCM.
View 14 Replies
So I decided to start the year with fresh oil. Like the hundreds of oil changes before, i changed the filter and added new oil. Only this time, oil started to drip off the bottom of the Oil filter at an alarming rate, only when the engine was running.
I figured the filter didn't seal well, so I repeated the oil change process. nothing changed, still leaking.
It was really cold (-10 C) when I did the oil change, I mention this in case it is a contributing consideration.
My truck is a 2000.
View 14 Replies
Well, get the engine running sound, then the drivetrain takes a crap on me. . . On my way home, about 60mph. Hear a noise from front drivers side. Gets to the point where I think I am losing a tire. Got out and checked the lugs, all clear. Got back in and the truck wouldn't move. Shifted thru all the gears, nothing.
Revved up to 1500rpm and it just sits there and shakes, like it wants to go but can't. No grinding or anything. Got a tow truck and as we were loading it, noticed that the front axle was rolling fine, but the rear was dragging. Tried it in N and D and it still wasn't rolling. Also observed drips on the flatbed and the drain plug on the transfer case was wet.
Praying that it is transmission, cuz I can just have them come get it and have it repaired under warranty. Heck its only got about 3500 miles on it. If its the hat to check? Ill be spending the rest of my evening on YT/Google. . . (Figured this was the right area to post this, cuz its a 99 7.3, I didn't see a dedicated drivetrain area so. . . )
View 14 Replies
Engine felt like it was running out fuel, injectors were clacking. I got home put on AE and it has a low high open on the code reading. took valve cover off and plug came out. I did the quarter modification.
Anyway took the truck out a few days later truck drove ok when cold then after about an hour it lost power again and started clacking until it died out. I had to stop and let it cool off about 10 times before i made it home. I changed ICP sensor. took it out for ride and about ten minutes later same thing. I have to let oil temp get down to 165 before i can drive it again.
When i first drive it Icp pressure is about 500 at idle and 2650 at full throttle, that is until it starts clacking again and losing power then the engine wont take any throttle..and ICP duty cycle is at 26%... Would bad IPR do this??
View 14 Replies
OK here's the deal. Cruising down the road at 55 mph, I felt a pop and then the engine just stopped running.
When I tried to start it up, no oil pressure. It appears that the IPR valve may have failed, but I'm curious if the pop was a catastrophic IPR failure or an indication of something else?
View 7 Replies
Here are some signs of the problem.
*Key fob does not work - battery is good.
*Interior overhead light works only on manual.
*Driver's auto door lock (with driver door open) will lock all four doors but the driver's door will automatically open back. To secure the truck I manually lock the driver's door.
*I replaced the driver's door 'ajar switch' with no results. The old switch was good after testing - normally closed until the ball is depressed then it goes to open.
*No codes.
*I just checked all the mini-fuses with a VOM and they are good.
*Could one of the relays be part of the problem?
I am curious if there is a scanner that can identify the bad door ajar switch if any?
From what I have read so far it appears the VSM (Vehicle Security Module) may be bad as a many of these 2002's complain of this problem and the VSM generally solves the issues. Are there folks other than the dealerships that can program the module if I purchase a new one and remove the old OEM one? Other than the inconvenience the truck runs fine other wise.
View 11 Replies
I am currently cab swapping my 2001 F250 with a 2005 350, I have everything installed but when I turn the key theres nothing... Dead in the water pretty much. I have power running to inside fuse panel but when I turn key there is nothing? no dash lights or anything, what I am missing or where I should be looking?
View 9 Replies
I have a 1999 7.3 super duty that won't crank when the key is turned. All lights work, power windows and mirrors work but after the WTS light goes out... Nothing...now I do have a slight leak in the roof and a little water does get in the cab. I opened my door the other day and it smelled like an electrical fire had occurred. I checked under the hood and the same smell, if not a little stronger. I pulled my fuse box and GEM tonight. Once I got away from the truck, I expected them to smell like the electrical fire smell, but they didn't. Now I did try cranking the engine over by jumping the starter relay before tearing the fuse panel out, and I got it to crank, but not strong at all. The batteries are good.
View 11 Replies
A few weeks ago I replaced my CPS on the 99 7.3. Today was the first day I drove my truck in the rain. When I turned my wipers on, I noticed that I lost power and my truck started hiccuping. I read on these forums that an aftermarket CPS is most likely the problem, so I am planning on getting a ford CPS this afternoon. My biggest concern is that before I replaced my CPS, my wipers only had 2 speeds. Also, if I pressed the end of the blinker switch to squirt the cleaner the wipers would not turn off until I turned the truck off. I am not sure why this would be happening and I wanted to ask if there is more than just the CPS involved with this.
View 7 Replies
I have a 2003 F350 SD FWD Dually With 4.10 Axle Ratio. I'm looking for some front rotors and pads and I'm looking for recommendations. I tow a 44' Goose neck racing trailer on a regular basis so I dont want autozone crap rotors that are going to warp in a few thousand miles. I was on rockauto.com, they have Wagner, Bendix, Motocraft, Powerstop, etc etc. I thought maybe those Powerstop drilled and slotted looked interesting, but I dont know much about them.
View 14 Replies
Recently my power windows stopped working...sort of. Here's what I mean: If the drivers door is closed none of the windows will go down. However, if I open the drivers door halfway or all the way I can roll up/down all the windows. If the windows are down and the drivers door is closed I can, almost always, roll up the drivers window, however the other windows in the truck will usually not roll up. Open the door halfway and up they go.
A couple of other things I have noticed. When I press the down button for the drivers door window, with the door closed, I can hear the relay, under the dash, kick on and the window will move about a millimeter down then stop. Additionally, the courtesy light on the drivers door comes on while the door is closed. I haven't checked if the other courtesy lights come on at the same time.
Hopefully my explanation is understandable. I would love to solve this issue. Getting tired of opening the door to roll down the windows. Plus when there's a fly in the truck and I'm driving I can't get it out.
View 7 Replies
Early 99 7.3 manual 6 speed. 224,000 miles. Truck starts great and runs great at idle. Starts out in gear just fine and seems to have plenty of power. It will act just like the key is turned off about a mile down the road. Will restart after extended cranking or letting it sit for 15 minutes or so. P1249, P0340, and P1280 codes pop up. Had a professional shop work on it and they changed out the CPS and IPC with factory parts. When i picked it up it had an SES light on but was running fairly well. When I looked under the hood the IPC had been cracked on the plastic part. Replaced it with another new one and it ran fine for 3 days, even pulling loaded hay trailer. Now when driving it, it cuts out for a second or two. It does that every couple miles until it stalls out completely. Restarts after 15 minutes and runs fine. Same codes are showing up.
View 3 Replies
I have a 2000 F350 with a 7.3 I have just set a brand new motor in this truck with everything in it new including the transmission injectors are 175/146 from Thoroughbred Diesel. The engine is Bored 40 over studded heads return regulator system as well as a pre pump filter and a javelin and Hutch mod on the tank. When we went to start this new motor the motor turned over and sounded like it was going to fire off pretty quick but instead I'm just getting white smoke and lots of it.
I failed to mention that the injectors are single shot vs. Split shot and then I did have the programmer Tuned to these injectors through thoroughbred there is no fuel in the oil no water in the oil no oil in the water everything seems to be good all the pressures seem to be good and at this point I am lost no one that I have found in the area, where to begin. Seems to me that this is a loading up issue and it seems to me that the only thing that could be causing this would be programming but I don't know.
View 14 Replies
I have a 2000 F-250 7.3 L Diesel w/200,000+ miles on it.
I use the truck for snowplowing and last snowfall one of my employees broke the overdrive switch on the PRNDL shift lever. I just replaced it and as I went to start the truck I had just turned the key to run in order to let the glow plugs warm up and the truck attempted to start itself.
As it was running I could hear the starter continue to run although I never fully turned the key. I have since then replaced the ignition switch and the key lock cylinder. That didn't fix the issue, I then pulled the fuse box that is inside the cab of the truck to inspect the GEM module. Other than lots of dust there was no corrosion or any see-able issues with the module. I cleaned all connections thoroughly and even applied a little dielectric grease to the connections.
Still has the same issue, I ran a voltmeter to the trigger wire on the starter relay and it reads 10V when the key is turned to run. I believe it should not read any voltage until the key is turned to start. If I have the trigger wire on the starter relay disconnected the truck won't start, obviously. I don't believe the starter relay is bad because it does start only when the key is in the run position and it has never attempted to start without the key.
View 9 Replies
