Ford 7.3L Power Stroke (1999-2003) :: Dropped Bolt Into Motor
Apr 24, 2017
So I was in the process of doing a turbo swap to the borg warner sxe366 and the freeze plug that plugs the old mechanical fuel pump in the valley had to be removed well needless to say, it as well as the safety bolt I had attached to it fell into the motor, seperatly. I'm already getting the motor ready to be pulled but what are the odds that they made it to the oil pan or if they didn't any way to make them fall out?
View 10 Replies
Advertisement
2001 ford excursion 7.3l diesel.
So I tried to go to work today but the truck said no. it started out fine then out of no where it felt as if someone slammed on the back brakes engine still revved up like normal just didn't want to go. speed dropped to 20mph then i heard a clunk. after that it was fine until it hit 20 mph again. it did the same thing again.
So I got mad at it thinking the trans went out gave it the beans and it shifts into all gears but did not feel like it had power. i did pull over and check the fluid looked a little orange. when got back in the truck i did notice the od off light blinking?? drove the truck home was shifting fine but hear this awesome sounded like a hand grenade rattling around underneath. when i got home notice fluid coming from the bell housing(out of the bottom).
View 14 Replies
So I received my International bellowed up pipes from Riffraff and I figure I will start soaking all of the bolts with some aerokroil before I get started on monday and I see the very last bolt head near the up pipe is gone. The bolt is there but the head is gone and you can definitely see soot buildup everywhere near it. I don't know if I should order a new manifold for the passenger side and new bolts, order a driver and passenger side manifold and new bolts, or just order one set of new bolts and try to get take the passenger side manifold off and replace the one broken bolt.
View 4 Replies
Like the title says I dropped about a 2 inch piece of small washer fluid hose in my cylinder while evacuating the oil from it . Will it damage the valves If I ran it? Any way to remove it without removing the head?
View 14 Replies
I managed to get the drivers side exhaust manifold and all of its bolts off no problem. On the passenger side I had 1 bolt head that was already broken and I have only 1 other that is still holding on for dear life. I've been soaking it in aerokroil for awhile now and no luck. I tried some PB blaster today because I am willing to try anything. I also tried heating up the bolt with a torch and some map gas but not sure if I am heating it up enough or not. Anyways, everything else has been going great, got the uppipes off and the valley, turbo and pedestal all cleaned up good. Just need to get the last whole bolt and broken bolt out so I can install the new manifolds. What I should try to remove the last 2 bolts. How hot should I get the bolt when trying to remove it? Or should I be heating the engine block?
View 12 Replies
Well i had an exhaust leak on this F250 and so I started torquing the bolts on the manifold to the head. (45 ft.lbs) A couple were very loose so I was thinking "Great, this may fix my problem!"
My first mistake was probably the Harbor Freight Tools torque wrench.
I am on the driver side, second from the rear and then bang! I see a gaping hole where the bolt used to be. Bolt on the floor. I cant see up in the hole to the head, I think it broke flush with the head.
View 14 Replies
As part of my ongoing P1393 troubleshooting, I’ve found that I can’t get the main engine wire harness separated. The big connector by the driver’s side valve cover.
I’ve cranked and cranked in the correct direction, but the plug never separates. I tried a cordless impact wrench and it still doesn’t move. (Edit -- the bolt moves very freely, but it doesn't push out one side (e.g. like removing the PCM) I can't figure out how to separate the two sides.)
Any tips on how to get it separated? Can I cut off the bolt head to get it separated?
View 14 Replies
The bolt that holds the dipstick on the valve cover. i have tried for ever to get this thing off. soaked it , got a skinny wrench on the nut underneath but think it might be stripped (1/2 inch grinded out a little). going to try and get a set of skinny wrenches tomorrow , mine bent. tried vise grips on top of the bolt and put a box wrench on the nut , and gave it my all. The damn thing won't budge.
Also, any tips on the rest of the valve cover bolts. I had to remove some from inside the fender well but barely got to them. My question is not getting these out but getting them back in. And how the heck to you torque these things??? The bolt i mentioned above is creating problem, and I only have so much time
View 8 Replies
How common is it for the hpop to leak from the round piece behind the pump next to the drain bolt? Its on a 2000 f350 7.3.
View 12 Replies
So I tried to replace my thermostat and housing and the housing bolt snapped off. Ok so I tried to extract that bolt off and the extractor bolt snapped off inside. I am guessing it might just be easiest to replace the water pump now? I am pretty much at the end of my mechanical rope which is short anyhow.
View 6 Replies
I have an Excursion with 220k miles. I've owned the truck for 6+ years and had very few problems. I change my own oil and fuel filters, but beyond that I know next to nothing about the diesel motor. I do run a DP Tuner with the standard 80 hp program. And a 4" exhaust. Everything else is stock. I do keep it plugged it for the oil heater and the battery tender just about all the time now.
This latest issue started yesterday morning when my wife jumped in a cool truck to take the kids to the dentist (not warmed up but still 55 degrees ambient). A few miles down the road (35 mph max) the motor began stumbling and rocking and black smoke coming from the exhaust with reduced power. She pulled off and kept it running (very rough and rocking) and put it in park for a minute. When she put back in drive, it shifted heavily but the power was normal so she went on her way without any problems. The only report I got sounded like the motor was just cold and rough, so I thought nothing more of it.
Yesterday evening we drove it about 70 miles on the highway (72 mph max) with no issue at all, but when we continued on surface streets toward our destination (50 mph max) it did the same thing, but would not settle back down. I kid you not that it went through gallons of fuel the last 12 miles or so, just dumping black smoke out the exhaust. It felt to me like we were running 1/2 the motor, like the plugs weren't lit. Very rough and rocking and very little power (comparatively, at least). I had to switch to manually shifting the trans to get going and the shifts were much rougher than usual. Idle was low and rough but it never stalled. Behind me there was a huge smoke screen this entire time.
We made it to our destination and parked it. Did our thing and after 5 hours went out with finger crossed. Started right up and ran perfectly the entire 91 miles home. No motor or trans issues at all. Currently running 10/40 synthetic oil that I just changed about 2000 miles ago. Oil level is perfect. 3/4 tank of fuel with standard level of Diesel Kleen added. Fuel filter is less than 10k miles old. Temps yesterday were 65-70 on the drive down and 50-55 on the way back.
I jiggled all sorts of connectors this morning and didn't find anything loose.
View 14 Replies
I have a 2000 f250 super duty extended cab with the 7.3 diesel and auto tranny which the tranny was rebuilt by Samco about 7 years ago and I have 337,000 miles on engine I had a oil leak from I believe my oil cooler which I fixed, but I am still losing oil, about a gallon or more every other day and in that time frame I am only driving maybe 30 miles. I have no drips, and I seriously don't believe it's burning because the truck is not smoking even when you rev the motor up. the bottom of the rear of motor is coated with oil plus as is part of tranny and some front of motor bottom. What to look for?
View 14 Replies
I have a 2000 F350 with a 7.3 I have just set a brand new motor in this truck with everything in it new including the transmission injectors are 175/146 from Thoroughbred Diesel. The engine is Bored 40 over studded heads return regulator system as well as a pre pump filter and a javelin and Hutch mod on the tank. When we went to start this new motor the motor turned over and sounded like it was going to fire off pretty quick but instead I'm just getting white smoke and lots of it.
I failed to mention that the injectors are single shot vs. Split shot and then I did have the programmer Tuned to these injectors through thoroughbred there is no fuel in the oil no water in the oil no oil in the water everything seems to be good all the pressures seem to be good and at this point I am lost no one that I have found in the area, where to begin. Seems to me that this is a loading up issue and it seems to me that the only thing that could be causing this would be programming but I don't know.
View 14 Replies
I don't know if its a coincidence but it rained hard all weekend and went to work this morning to find out the blower motor only on 4(high). I checked the plug going into blower motor and it looks dry and clean. is there a common occurrence with this? What to look for?
View 14 Replies
I have. 2001 excursion with a 7.3l deisel. 167100 miles
It runs great but if it sets over night when the motor is cold it will not start.
You have to plug the block heater in for about an hour or more for it to start.
To me it seems like glow plugs are not working? It had new glow plugs out in from the po.
View 14 Replies
For the past few months my bower motor will stop working. It could stop while I'm driving. Or not work when i start the truck, then start working while I'm driving down the road. When it was working it worked fine. It had the different fan speeds like it was supposed to. It would just not work at all, or work fine. Now it doesn't work at all. I checked all fuses, and swapped the relay for the windshield wiper relay that i know works and still nothing.
I unplugged the blower motor and put 12v to it and it didn't work so i thought i found the problem. Took out the blower motor put power to it again and it spun just fine. Plugged it back into the harness and it worked other than no low speed. Flipped the switch back and forth, then low speed worked, up to high, but no difference between speed 2-3. Put it all back together and it seemed like all the speeds were working fine. Day later, won't work at all again.
View 2 Replies
Do we need to drain the fluid to change the transfer case motor?
View 3 Replies
My feed truck (2001 ext cab 4x4 7.3 198k) had a cold starting issue I fixed with new gp relay. Now I noticed when it gets down below 30 degrees it has a cylinder miss until motor warms up. I don't doubt injectors are in my future. I was wondering though if that is common for worn injectors or if maybe something else has gone haywire and how long can I run it like that before something else tears up? after about 7-10 min the miss goes away and I don't notice it. I would like to get through the winter before messing with it or having injectors put in it...
View 14 Replies
I just replaced my Wiper motor last week and noticed something strange. For the last year or so when I turn on the key to start the truck, once in a while my radio, gauges, and other electricals such as windows wouldn't work for a bit, anywhere from a couple seconds to maybe as much as a couple minutes. Since my wiper motor was on the fritz, I pulled the fuse and the radio,gauges,ect. wouldn't work until the WTS light went out, then everything worked just fine, even after I started the truck and the glow plugs come back on.Since I replaced the motor everything works as soon as i turn the key. Coincidence? Or could one of the internal relays on the motor being stuck cause that?
View 5 Replies
The night temperture was only about 37 degrees. But every morning my 2000 F-350 7.3 crew cab 188,000 on it would not start. The first try there would be a split second where the motor would fire, but that would be it. I had to plug the engine block heater into my generator for at least an hour before it would start. I don't see how all the glow plugs could be bad at once??
View 14 Replies
I am fairly new to powerstrokes, but have a general understanding how the 7.3l operates, and how the fuel system works.
The problem i am experiencing is a crank, no start. The truck has been great for the year and a half that i have owned it. Always cranked great and never any starting or running issues. One day upon cranking, i started the motor; it started normal running good for a minute until the motor suddenly started shuttering and then the motor shut off, happened rather quickly. The truck started up immediately after that and died....repeating the shutter until dead. Now the truck will not start.
Specs on truck:
2002 7.3l
230,000 miles
Manual transmission
Here's what i have replaced so far:
New parts include:
IPR (motorcraft)
ICP (motorcraft)
EBPV (napa)
CPS (napa)
IDM (reman)
Here are some of the diagnostic values i have collected during cranking: (FYI: i am a little confused on what the values mean and what they should be in order for the motor to start):
ICP: 2218 psi
ICP duty cycle: 41%
EBP: 265 kpa
battery voltage: 12.0
Rpm: 355
Things i have checked so far:
Oil is new and level is good.
WTS light cycles as normal.
Fuel bowl is full and over flows with cap off while cranking.
Fuel tank is above half.
Glow plug relay is good.
I was throwing a code for the PCM, but i removed the bully dog tuner and the code has since cleared.
HPOP oil is an inch below full.
I made a gauge set and dead headed HPOP yielding 1500psi.
Upon cranking i am seeing some smoke, i guess, but its kind of hard to tell from the drivers seat.
This is where i am at so far. I don't have a way to buzz test the injectors or tell if they are leaking past the orings. I have the valve covers removed, but i have been putting off pulling the injectors to replace the orings.
View 14 Replies
