Ford 7.3L Power Stroke (1999-2003) :: Dipstick Tube Adapter Flange Leak
Jul 21, 2017
I had a leak at the flange several months ago. I fixed it with the diesel o rings kit. I made a trip from TX to AL with no leaking and drive it daily without leaks. But, 2 weeks ago noticed a small dribble of a leak from the same spot again - not enough to leave a mark on the pavement but any leaking drives me nuts. I applied some RTV. It worked for the 2 weeks.
Today, noticing another dribble of a leak coming through the RTV down the pan. I'm thinking the flange is bent and not keeping that o-ring sealed against the pan. I'm going to try to apply some additional RTV at the leak spot. If this doesn't work? Is that Strictly Diesel adapter really worth that kind of dough? Is pushing the OEM adapter into the pan really acceptable? Any other options?
View 14 Replies
Advertisement
The dipstick tube flange is now leaking ....
View 3 Replies
Heading back up to get the last load of antique tractors from the show and something seemed funny. 2 miles later turn into a side Road less power. Pull over. Oil everywhere. Shut it down. Nut completely unthreaded.
Get it on and tighten as best I could with a pair of channel locks one size too small. Dump in a gallon of oil. Now it is just on the stick. Start it and sounds good. Still leaking.
Called a buddy to see if he can get me. Yep sure but his wife is not happy. Something about him going to Texas at 7 am for work for a week..... Give him directions hoping he makes it since he has no sense of direction.
Obs 7.3 stops. Talk to him. He doesn't have anything better for tools on him but lives a mile down the road. Drop the trailer on the side of the road. Drive to his farm and got some better fitting pliers. Either I got too heavy handed or I cross threaded it. Stripped the nut. The flange threads look good.
Drive back to the trailer and sit intersection so my buddy doesn't miss it. Hook my trailer to his truck and get mine loaded. In the end it turned out as best as it probably could have. Pictures to follow when the sun comes up. Time to read up on the dipstick flange. Hoping a new nut and o-rings will fix it.
View 14 Replies
I have a 2001 7.3 and have found the engine oil dipstick coming out of the dipstick tube by 6 - 8 inches on three different occasions. Did not think much of it until my other 2000 7.3 did the same thing.
What causes this as afraid it will come all the way out and get into the serpentine belt.
View 6 Replies
So after a hot drive yesterday we thought to do some googling about our clutch cycling on and off so fast. Yep, the airgap was out of spec. Fixed that.
Then we added some refrigerant to the truck. The truck is "new to us" and this is our first summer with it so not sure what might've gone on previously with the AC. Didn't take long to find a rather sizable leak. :P
See that metal tube going into the "spongy" area? Yeah, that's where it seems to be coming out. That tube is the only one that's cold, the rest are ambient temp. We fix a lot on our jeeps, but the AC system is naturally a bit out of our wheel house since it's not something you normally tangle with. Is this an easy fix? Or do we need to take it in to get serviced?
View 12 Replies
I have a minor leak at the base of the trans dipstick tube. I assume that the tube is press in ? has an o-ring ? I put some silicone around the area and that worked about a week, the fluid is probably eating through that type sealant. The trans is a 4r70. Seems to me that the actual tube should be ok and having never dealt with replacing one I want a little advice before yanking it out.
View 11 Replies
Pulled my dipstick out to repair the flange seal where the tube goes into the pan. Now it sticks out about 2 inches. Ive tried putting it in both ways. Now it was sitting in my truck over the front seats with the center armrest down, so it may have gotten bent the wrong way? I read a few tricks online Ill try after lunch here. I did have some vice grips on the tube to try to get it off of the flange, but I took my fingers and felt the entirety of the tube and didnt feel and dents or irregular bends. Right now the tube is held by zipties, as I had to cut the bracket off, its a long story. . . So is that something that would make it stop short? Does this truck have a 2nd tube that sticks into the oil pan or is it just the one?
View 13 Replies
I am doing some maintenance and trying to replace my EBP tube and sensor. I luckily have the dual alternator package, so getting the tube in and out has been a pain to say the least. I can't for the life of me get the tube back into place. As always, a 20 minute job is taking me 2 days.
View 14 Replies
I've had a shifter-related short on my instrument panel and stereo lights for close to two years now, and it finally got so bad I had to dig in and decided to proactively replace the shift tube while I was digging in. After all, the existing one had 290K miles on it. Although the lighting issue drove me to replace the shifter tube in hopes of finding a damaged wire, but this issue has now been moved to a separate thread [URL] ...... The remainder of this thread deals with my difficulty with the new hardware.
So, I compiled all the info I could find on replacing the shifter tube and did the replacement on Saturday (Dorman shifter tube kit from O-Reilly's). The Dorman kit was fine, mechanically, and the parts fit together well. I did, however, have to smooth out some burrs and sharp machining edges where the new nylon bushings go just to prevent premature wear on them from the sub par machining cleanup a the Dorman manufacturer. I also inspected all of the wiring harnesses and connectors carefully, but could not find any evidence of a shorted wire anywhere.
Results... Shifter Movement: Overall, the shift movements are much more secure and smooth as butter, even though the shift arm itself still has slop in it where it gets pinned into the tube housing.
Now that it's all together, though, I can no longer shift down into 1st gear, and getting it into Park to release the key is tedious. I uninstalled and reinstalled the rear shifter bracket three times (the one which is typically related to not being able to get into Park and 1st). I carefully made sure that it was tight and completely flat against the rear of the shift tube each time. I just cannot tell why getting into Park is tougher than it used to be, nor can I find a physical barrier preventing it from getting it into the 1st gear position.
So here are my questions:
1. The steering column mounting flanges have some adjustment slop around the two rear mounting bolts, and the front two bolts also have minimal "adjustment" capability. Is ti possible that my entire shift positioning problem is due to not having the steering column physically mounted in the right alignment and that is restricting motion on the gear shift flex shaft?
2. If the answer to #1 above is "no", then what else do I need to be looking for to resolve this limited shifter movement?
3. There is a solenoid switch at the rear of the shift tube... is it possible that this is going out? I honestly do not suspect it because I have no trouble starting the truck when in Park, but I have not yet verified the effect of being in "R" on whether or not my backup lights come on.
View 6 Replies
Rusted dipstick tube I thought was going to be an easy enough fix. Broke off clean at the block. Tried for hours, easy out, prying, vise grips anything I could think of. Well I tried to pry the side of the tube over to make room for my needle nose vise grips, and boom. Down in the oil pan it goes.
Do you think theres any way possible I can fish it out through the drain plug. I really dont want to pull the darn motor.
View 7 Replies
I have a '99 F250 SD 7.3 & im going on a trip next weekend so I thought I'd pull the exhaust pressure sensor & clean the tube in an attempt to get better mileage. Found the sensor & unplugged it. Went to the manifold & started removing the tube when it fell off. 6" from the manifold it's broke & the rest is completely missing.
Autozone doesn't carry this tube so, how important is this sensor?
View 7 Replies
The bolt that holds the dipstick on the valve cover. i have tried for ever to get this thing off. soaked it , got a skinny wrench on the nut underneath but think it might be stripped (1/2 inch grinded out a little). going to try and get a set of skinny wrenches tomorrow , mine bent. tried vise grips on top of the bolt and put a box wrench on the nut , and gave it my all. The damn thing won't budge.
Also, any tips on the rest of the valve cover bolts. I had to remove some from inside the fender well but barely got to them. My question is not getting these out but getting them back in. And how the heck to you torque these things??? The bolt i mentioned above is creating problem, and I only have so much time
View 8 Replies
I got a 97 F250 4x4 w/ 4.6 lt. motor & auto trans. The engine is leaking oil. It looks to be coming from a set of hoses that are on the adaptor that is between the oil filter & the engine block. Also what are the oil lines called? It is leaking motor oil not transmission oil.
Also just pulled my oil dip stick & the whole thing (dip stick & the tube) came off the truck. Seems the tube has rotted away at the oil pan. Is this also a job I can do?
View 6 Replies
I am doing the usual upgrades on a 2005 F250. What started as a small leak at the rubber coupling between egr tube and oil cooler turned into doing everything else while motor is down this far.
I am curious what the difference in the upgraded oil cooler is? Well besides not prone to failing as early.
View 4 Replies
The dipstick tube on my 5.4 snap and ive ordered a new one. it looks like it may not be to hard to replace.
View 4 Replies
Ford F-150, 1999, 4WD. My dipstick tube has rusted off right at the point where it attaches to the engine block. I purchased a new one but I'm not sure if that's a job I can do on my own. What installing a new tube will entail?
View 5 Replies
OK, so I have a 01 f350sd and i went to check my oil and the dipstick tube itself is so rusted it snapped in half so I took it to the dealer which I knew was going to be over priced labor but still checked the tube itself is 20 dollars but labor is upwards of 300-500... My engine is the 5.4 triton.
View 2 Replies
I just finished putting a 7.3 back in one of our f450 plow trucks today, so then i moved onto our 2001 F250 5.4 plow truck. The dipstick tube was rusted in half so i pulled on the remaining half to get it out and put in the new dipstick. However, it broke off at the block. So now i cannot see how to get the rest out with out doing a lot more work. I haven't removed the splash guard yet but will i have to remove the manifold , the oil filter base, or both?
View 14 Replies
I have a 03 F-350, 7.3L. There is a slow oil leak that only leaks after I've run the truck. In other words, it doesn't just sit and leak overnight. I'll park it after running, and the next morning I'll notice a small pool of oil, approximately 2" in diameter. The leak appears to be coming from the oil pan area. I degreased the entire oil pan area to get a better visual of where the leak is coming from. I can see oil trailing down the front of the oil pan and the rear of the oil pan. Does this sound like the gasket? Or, what else could it be? I'm praying its not as bad as I think and need to replace the gasket.
View 3 Replies
This was briefly discussed as part of another thread. It appears that I have a boost leak when I hit roughly 24.5 psi. The leak seems to stay for a few minutes after showing itself, but then I'm able to produce boosts up to 24.5 again. For example, on my 20-mile/30-minute drive to work, I can make this leak "appear" four or five times, maybe more if I try. Does this self-healing leak ring a bell? I haven't done a boost leak test yet, but I'm leaning towards the RTV sealant at the OEM plenums due to the self-healing attribute.
To add a little info to this thread, I recently installed an S&B intake, 4" exhaust, bellowed up-pipes, RR billet wheel, RR CAC intercooler boot kit with new clamps, RDP reinforcing plenum inserts, AIH delete plug, and I removed the wastegate solenoid along with the red and green tubes. I don't have any gauges, but I recently began monitoring the boost using FORScan. Before all of this, I don't think I was producing enough boost to cause this leak, and I had no way to monitor for this leak.
View 14 Replies
Brothers of fte. I reach out. Tonight it appears I had a fuel bomb under the hood.
I've been chasing a fuel leak. Replaced fuel drain orings but one screw seemed to not snug up. Also the plastic was so brittle I couldn't replace the inner oring. Installed new valve worked great. A week later noticed new slow drips. Replaced fuel filter. Again good for two weeks.
Tonight pulled into the driveway hopped out immediately smelled diesel. Steaming from under hood. Popped the hood and everything was wet. Moved her to the street and it clattered like I was running out of fuel. Still half a tank though. Hosed of the drive. Popped hood again fired it up easily. Started fine. No noticeable leak. But everything is wet from fuel. Insulation on hood was saturated. When I open the hood fuel ran out of the insulation into the air intake. Batteries were wet!
Alright what gives? Do I have to be under load to see this leak?
View 6 Replies
