2002 - 7.3 lariat, my a/c stays on max because of the recirculating effect. When I get in the next morning during summer of course, my dash vents take a few seconds to begin, default defrost till that time passes. Sure I know about leaks and redone all that to make my vacuum hubs work correctly. It didn't begin till later not right after that overhaul.
View 11 RepliesAs the title implies, that is my problem. Can't get the AC to come out of anywhere other than the windshield defrost vents. Y'all ever encountered this before?
View 4 RepliesAll vacuum lines are good, pump works, Canister isn't leaking, 4x4 activates and I can feel it, so Can't be vacuum leak. Replaced esof solenoid 6 months ago last time this happened, but this issue seems to be different. Watch this vid I made showing the issue.. after viewing video, do yall' agree I isolated the issue? If that one tug makes the air go through the front vents, that means everything else in the A/C mode selection works..
YouTube.....
The floor and defrost vents work. It just stays on defrost when you try to use the dash vents. The actuator seems to be working fine. I can watch the arm move through all the motions. and I cant find ANY vacuum leaks. Yes I looked at the hubs and under the hood. May be moving to alaska and kind of need my heater to work properly. . . .
View 5 RepliesI had the engine out of my truck (7.3 with e4od) to do manifolds. Anyway, I got it back in and started it up. Since there was air in th fuel lines it had to crank a couple seconds but started up. I looked and now fluid coming out, then it sat for a few minutes running and I took it for a drive. While sitting in the driveway it wa smoking a bit. But I thought it's from the oil I got in the exhaust while drilling two of the manifold bolts and soaking the bolts with ATF/acetone. After about half a mile I thought that maybe it's more oil then that would cause... So I went back. I looked and the inside of the exhaust is covered with oil, and the rear of the engine is also.
When it was out I capped all of the open ports so I could pressure wash the grease off. Also, I flipped the CCV so I could do the delete. During instal, I missed the cap on the CCV and it was not able to breath. I think that maybe it built up pressure and blew the valve cover gasket? It looks like it's coming from the right cover on the backside; I had not taken this cover off while the engine was out. How much pressure does it build? Is it possible that it could have blown the gasket out? I have done the oil cap trick to test blowby and it always passed the test. What it could be? For the leak on the engine and why it's in the exhaust?
4.0 v6 A/c works great at first. Then after a while stops blowing out the center dash vents. What to check? Still blows cold out the vents by each front door...
View 2 RepliesThis applies to a 2001 F-350 with 73,000 miles on the engine. Engine oil level is good, batteries charged, HPOP reservoir is full and passes Cody test with flying colors. Fuel pump runs for 20 seconds at key on. Start takes about 6 seconds. If I shut the key off and restart immediately it starts in under 2 seconds but if I wait about 30 seconds it's a 6 second start. Here is an AE that I ran on it, it has me stumped. FWIW it seems to start quicker when AE is hooked up. ?? An odd whir type of noise comes out from somewhere under the hood when I first turn the key on and when I clear the codes with AE.
View 14 RepliesMy heater vents have been acting up. I have read that there may be a vacuum leak that causes the blend doors to default to defrost...
Where the vacuum line fails? I have ESOF 4x4 and that is still working. I think there may be a correlation between engine vacuum and my vents: at cruising or idle the vents work ok (not perfect) and under acceleration (less vacuum) the dash vents stop blowing.
I thought that the blend doors had their own vacuum pump, so I do not know why things change at different amount of throttle?
After some diag I got the A/C to blow out the front vents. There are million threads on this issue half of them are never figured out. This is the second time I have come across this problem so will make this really informative for those who have this problem. If you A/C blows to defrost, yes most of the time its going to be a vacuum leak issue.
Step 1) turnkey on engine off, stand by passenger fender and listen.. can you hear the pump running? If it is your pump isn’t dead.
Step 2) does the pump run for 30 seconds then shut off? You may not have a vacuum leak. If keep’s running for ever you have a leak. Inspect all lines, especially those going down to the hubs for cracks. Also inspect vacuum lines under passenger glovebox.
Step 3) can’t find a leak? Disconnect the line going to the ESOF solenoid and plug it, if you pump stops running then your ESOF solenoid has an internal leak. That was my problem 6 months ago, replaced ESOF, A/C blows normally.
Try This Second! So my AC isn't blowing through my front vents again.... (more diag)
AC not blowing through vents and can’t find a vacuum leak? Take off glove box door, turn AC control switch to floor/defrost/front vents, watch the metal arm connected to the side of the big black box move up and down into various positions. I noticed on mine the arm will go down in positions (floor or defrost) But it will not move up! Which needs to happen to switch to front vents. If I push the rod up by hand manually, the ac will blow through front vents, and stay blowing through front vents even after I let go. PIC of metal arm thing connected to diaphragm, which changes air flow by moving flap inside the big black box
I am guessing the Diaphragm is the issue? The truck will continue to blow from the front vents even when the truck is shut off and restarted, it will stop when I switch the ac to a different position, it will not return back to front vents.
I just replaced the blend door actuator. But now when I am driving its blowing cold air thru the dash vents one minute then super hot air the next. Also I had a problem installing the actuator over the keyed shaft on the housing...
View 1 RepliesI have an 03 F250 7.3litre. I have noticed the last few times driving while hauling that my vents start pushing hot air when under a load (example: driving up a long, steep pull) even if I have the AC on. It's starting make me a lot hot under the collar (pun intended) .....
View 14 RepliesI noticed a couple weeks ago after starting the truck and turning on the a/c that nothing was coming out of the vents. I found it odd when after driving a few miles the a/c kicked in and started blowing cold air. Today I needed to put on the defrost and same thing, nothing came out of the vents. I drove around for a while hoping it would kick in just like the a/c did but nothing. I did check the fuses and relay. When you turn the control either to heat or a/c you can hear a clicking sound under the hood. It's trying to engage but nothing is coming out of the vents.
View 12 RepliesMy 01 ac has worked just fine up until today. I got in this morning to leave the house and the air was only coming out of the defrost vents. I tried playing with the controls to get it to switch but couldn't. I assume its a vacuum leak, but where do I need to start looking?
View 14 RepliesI have a e99 f350 7.3 all stock. I have no power. The truck will crank for about 15-20sec before it'll turn over. I just purchased the*AE*but am fairly new to understanding it all. In idle its a little rough and when I drive I can only stay in the neighborhood because of fear of getting rearended due to very slow acceleration. Whats weird is that when i have no power while i am driving ill keep the pedal down throw it in nuetral and my rpms and*icp*pressure jump up right away. Things I've replaced:
Icp*sensor
Fuel pump
Pcm
Tps
Cps
Ipr
Dropped tanked and cleaned screens
When cranking my*icp*pressure climbs slowly to right under 500. I dont know what else to do ive been working on this truck dor two months some days 13hs straight, I am feeling defeated. Codes p1249 1211 1209....
I have a 2002 F250 7.3 with 130,000 miles. The truck was bought new by my father and is completely stock and never run hard. I was driving on the interstate at 70 mph and the cel came on for 30 seconds and went off. Not long after it went off the truck shut off and has not started back. That was around 12-20-16. I have put a new cps, icp, and ipr on it with no luck. All ford parts. I drained the fuel water separator to check the fuel pump and it filled back up. The truck is turning over good but has no white smoke witch leads me to think maybe the IDM. I'm a novice to all of this and until this happened new nothing about any of these parts but I'm learning. I do have the torque app if I should check some things.
View 14 RepliesI have a 2001 F-450 SD with 7.3. What the problems would for the blowing of fuse #3. The DLC fuse. I mean I know it goes to the cigarette lighter as well. but when not in use it still blows.
View 1 RepliesI am a mechanic and tow operator running a late 99 f350 7.3 6 speed cab and chassis wrecker. This truck has had a hard life and has been neglected for quite some time, and now has become my baby/headache. Truck starts great, idles nice, and will run great for about 5 minutes until it starts billowing white smoke that smells like fuel and loses all power. If you continue to drive it it will die. Sounds like it's dropping cylinders and will barely idle. If you stop for 5 minutes or so and let it idle it will smooth back out and will run great again for another minute or two, then right back to stumbling.
Using torque app, hpop pressure looks good when it's running well. Peaks at 3k, IPR maintaining 30-40% max. As soon as it stumbles you can see the hpop drop to 5-600 and the IPR will climb to 65%. Let it idea bit and they go back to normal, and stay good until it stumbles again.
Ive changed the fuel pump, ICP,rebuilt FPR, change fuel filter, pulled and cleaned the fuel tank (metal tank, no delamination, looks perfect inside). Pickup screen looked good. Cleaned the IPR, cleaned the hpop reservoir, there was no screen inside. Checked voltage at fuel pump, 11.78 across the pump with it running. Pulled valve covers, no noticeable leaks around injectors. Injectors have less than 5k miles. Remans with 100% larger tips.
To me it seems like the lpop is not keeping up with the hpop under load, starving it until you idle and let it catch up. Could it still be bad injector orings? Bad lpop? Something I'm not thinking of?
2000 f350 CCLB SRW 176,000. I have a touchy accelerator. About two weeks ago the CEL came on and it wouldn't do anything but idle for about 20-30 sec then fine. Then it got a little worse. I disconnected the two harnesses on the accelerator pedal and sprayed them with electrical cleaner. Put it back together and it seemed to be ok. Today the pedal is real sensitive. Sometimes bogging down other times accelerating real high even tho my foot is pretty consistent and gradually accelerating. No CEL tho. Do you think I am in for a new pedal assembly? Could it be something else? UVCH?
View 13 RepliesI am a longtime 7.3 IDI guy with an 88 F350 crew so i know about diesels. But this is my first electronic diesel. I picked up a 2001 F450 2wd auto 260k miles. it used to be my work's truck but was stitting for a year and now i got it in "non running condition"
I towed it home and got it started by replacing the batteries and using the block heater.
As expected it took a few tries of long cranking to run the first time. runs pretty good and no smoke. what surprised me is it still takes about 5 sec of cranking to restart each time when warm too. any direction you would look with those symptoms? HPOP, IPR?
i am pretty sure the glow plugs all work because mechanics had replaced all that stuff. but i know back when the truck was last used it would still never start cold unless plugged in (even in summer).
My buddy's '05 will not blow out of the dash vents, you can make the a/c blow out the defrost or the floor but no dash. Vacuum pump is working great, rarely ever kicks on and doesn't seem to be leaking anywhere in the system that I can tell yet. Pulling a vacuum on the red line will make it start blowing out the vents so the door is functioning.
I thought maybe I had narrowed it down to the ATC solenoid and manifold (Ford part #5c3z-19d611-aa) not working properly but found that the F-150 guys having problems with the o-rings on the back of the control head. Seems they replace the 4 o-rings and all is well, cheap easy fix. Are the units on the diesel set up that way too?
A quick search for EATC problems on the diesels didn't bring up much, seems they don't tend to fail. He's wanting to sell it and asked if I could try and fix the problem. It's been about a year since I last looked at it, so my recollection might be a bit foggy.
I recently installed an egr delete and ever since, my vents have been stuck to the upper dash no matter which setting I put on. The vent will push the air conditioning, regular air and heat all the same. I have checked the fuses and they are all good.
View 5 Replies