Odd question, but the a/c clutch has always engaged randomly even though the a/c is not on and even now when the heat is on. Is this normal?
View 7 RepliesI have my vacuum system back up and working and using my vacuum pump I determined my lines are all good. They hold a vacuum fine, but my ESOF isn't engaging my hubs. I guess that leaves either the selector on the dash or the seal at the hubs.
If it is the selector, I should just be able to just disconnect the vacuum line at the selector and use my pump to engage my hubs. How much it is supposed to take to activate the hubs?
I just bought a 99 F350 to replace my 01 F250 5.4 and I'm pretty stoked. There are several problem (some i knew about, some were surprises) 1 of which is the starter. The guy I bought it off said that every 100 starts or so (more like every 4-5) the starter sounds like it free-wheels but you just wait for it to stop, turn the key again (sometimes twice) and it engages and starts (although it takes a few seconds of turning over before it fires up).
I have a buddy with the same truck and he has had to replace his starter many times and I read in an old log book from the original owner that he had replaced the starter every 25,000kms (15,000miles). I am not the kind of guy who likes to fix things to have them break again.
SO my question is, WHY do the starters on these trucks keep breaking? What is the weak link? Is it possible to re-build one with better parts at home?
Is the problem partially because my batteries are only 650CCA and 750CCA and it takes more to turn this beast over? Could it be a bendix issue?
Ok, the swap is all done and I have an engine in the truck that has compression in more than (7) cylinders.
2002, 7.3, 4wd - ~120k miles on trans. Fresh fluid (Mercon V).
Put the gear selector in reverse and it goes right into gear with the normal tug and functions as it should. Put it in low gear and it also appears to work fine. But, when selecting '2' or 'drive' it feels almost like its engaging 2 gears at once?? There is limited forward motion and it feels like the brakes are on. I have not driven further than the driveway yet, but I have a long driveway...
The OD light does not come on. I am not getting any codes from AE, but I really don't know how to use it for transmission stuff (I've been using a different scan tool that I no longer have).
We have not put the bed on the truck, so no tail lights - but 3rd brake light has new bulbs and was working (didn't check this AM though... )
I have a couple other codes, CEL, 'check gauges' and no tach. Gonna start another thread for those issues, I'll put a link here in case its related.
So I just bought a E99 f350 lariat. I wrecked the truck on the test drive and felt like the right this to do was to buy it. Finally have everything fixed and replaced on the truck and have run into other issues now.
While flushing the coolant system I started noticing that the starter was engaging randomly. After doing some research I found out it could be the GEM under the dash. Looked under the dash and I could here a sizzling sound and seen "smoke" /water vapor something coming off the GEM. And there is water coming through from the window/cab lights.
So. All the post I seen where from like 6 - 10 years ago. Where is the best place to buy a GEM? Will having the window replaced take care of the leaking issues on the window? What's the best after market cab lights? Cause I think they are leaking too.
What EOT temp should the fan clutch kick on at? I've never heard it kick on until a recent trip. It seems to go on about 228 degrees EOT and keeps the EOT below about 232 degrees.
At slow speeds I've found that the trans will heat up to this temp too. I assume because the radiator cooler is at that temp an there's not enough air flow for the air cooler to cool it down much?
Is this the sign of a bad fan clutch? I can spin it by hand,and it goes round and round.Can I drive it like this until I replace it? I am only driving 30 miles round trip at night, not towing and outside temperature is usually about 100 degrees.
View 6 RepliesIts freaking hot! Only getting about 65 degrees out of the vents at best. If I start up and let idle the a/c clutch goes on and off but not after i rev up the engine or drive a little ways . plenty of freon, and the air gap is tight with .020 and .021 feeler gauge. Should I still pull one of the shims? or is it something else? Last summer the truck was like a meat locker. I did have to add some freon about 6 weeks ago but seems to be holding ok...
View 14 RepliesThe fan clutch will come in and out rapidly when NOT in OD and pulling hills with the fifth-wheel attached. Replaced with a new aftermarket fan, then a new OE one. Then had the radiator pulled and all the bugs, etc. blown out. The condition has not changed at all. The original fan clutch was pretty sloppy. There are no codes, the trans fluid is nicely red, the engine does not overheat or even change temp when pulling hills. No check engine light ever. The truck is a 2001 F250 4 X 4 automatic extra cab with 7.3 engine without any modifications and runs perfect except for this. There are about 95k miles on odo. When we use overdrive on the flats, there is no issue.
View 12 RepliesIn my 99 with a zf6 it seems like when I push the clutch to the floor it's not disengaging all the way. It has a newer valair clutch in it maybe 15000 miles on it. It's really hard to get the truck in reverse or first from a stop. If the truck is stopped and it's in reverse or first with the clutch to the floor it will move in that gear. Is there a adjustment on the clutch? I'm thinking no since its hydraulic....
View 14 RepliesWell, I think my clutch is falling apart. I am hearing an intermittent nasty noise coming from somewhere in the bell housing/oil pan area. It comes and goes, but seems to be more frequent lately. It sounds like a dryer that somebody threw a pair of sneakers and some rocks in; with a metallic clunking noise of something being "churned" around. As I said, sounds almost exactly like the dryer thing.
The clutch does not seem to be slipping, but I do occasionally have difficulty getting it into gear at a stop. I'm guessing that the clutch disc has thrown a hub spring, and its rattling around in the bell housing. Assuming I need a clutch; which I think I do, I need selecting one. I have no history on the clutch or flywheel, so I will assume that I need a new flywheel to match whatever clutch I get.
I can't get a stock replacement, due to the injectors/chip/etc.... I would estimate I am making about 350hp/700ft-lbs. I don't tow currently, but I may pull a car trailer in the future. I DO haul heavy loads in the bed (4,000lbs) on a regular basis. I also drive/shift aggressively, as well as shifting quickly. While I spend a decent amount of time on the highway, I also do a lot of stop and go stuck in traffic driving; so smooth engagement is important. So, no ceramic/ceramic in/out type clutches.
I do NOT want a South Bend. I don't want a super soft pedal. Also, the whole pedal-sticking-to-the-floor thing they mention is unacceptable. Personally, I think they should be ashamed of themselves for putting out a product with such an obvious unsafe design/engineering flaw, and then try to explain it away as "normal". Nope. They need to go back to the drawing board and fix that. As I said, it constitutes a serious safety hazard.
I'm getting ready to swap my clutch and got to looking at the slave cylinder. I read somewhere that you have to rotate and twist it to get it out? Or something else? Also after reinstalling how do you get the slave plastic piece cut that holds the rod in? Or do you just push the clutch?
View 4 RepliesWhat is failing. I have a 2000 F350 PSD with 116k miles. When I bought the truck last year, I noticed that the clutch pedal would squeak while it was coming off the floor. It doesn't happen when the engine is cold. I need to drive it about 30 min before it starts to happen. On longer trips, several hours, the squeaking is louder and the pedal gets very stiff. When I stop for fuel, I've come close to stalling when coming out of 1st gear. I can push the pedal to the floor, but on the way up, the pedal squeaks, and then once I reach a certain point, say 3-4 inches off the floor, the pedal looses all freeplay. The best way for me to describe it is the pedal travels up faster than it normally does when it's cold, and if I don't compensate with more throttle at that point, it will stall.
I've learned a lot by reading this forum for the past year, but I don't know the first thing about how to diagnose problems like this. I've taken it to 2 mechanics for test rides -- one thinks the clutch is fine and thinks the problem is the slave cylinder or a broken bushing in the pedal.
The other shop is also a small independent shop, but they specialize exclusively in Ford trucks, so I thought they would be more knowledgeable. But now I'm wondering if they could sense my ignorance and are taking advantage of the situation. They also took it for a drive, but they think the slave cylinder is fine and that the clutch needs to be replaced. I questioned him about the slave, and he pulled it to look at it, and asked me to push the pedal slowly while he was under the truck. I still had a little resistance and a faint squeak even in this situation. But he said the hydraulics are so simple that he felt we could rule that out. I can't remember exactly what he said, but I think he believes one of the springs in the clutch plate has failed. I just know they are suggesting a new clutch and they want to machine the flywheel to original specs.
I thought the leading symptom of a failing clutch was slippage under a load. So under strain, I would expect my engine to race occasionally, like I'm in neutral. But I've NEVER experienced anything remotely like this, even when driving hard in the hills pulling my travel trailer.
I know something is wrong, but based on my limited knowledge, I'm not sure what. It's getting a little harder for me to move the shifter into 1st and reverse, but once it's there it's fine. I've never experienced any racing or slippage in any gear. The one definite symptom I have is that squeaky pedal that when driven for a couple of hours, gets so stiff that it can cause near stall outs. With those symptoms, what do you think is going wrong?
On 2500 mile trip, no A/C last 400 miles and we're cooking
Compressor clicking on/off about every 5 secs, clutch smell. Seems to be turning okay.
I brought some tools, including a full socket set.
Can I pull the clutch and remove shims in the campground? Looking for a condensed version of how?
Worst case, how do I replace the clutch- of I can find a dealer with one?
Pulley and clutch fixed, but cycling on and off...adding freon?
So I have the luk full ceramic clutch now, this is my second one (about every year it needs replaced) and it's getting close to needing a new clutch again. Right now my 7.3 is sitting at 442hp and 864 TQ. Im Building a forged rod motor with the idea of getting 5-550 HP to the wheels out of it and hitting the 1000 TQ mark. What clutch will hold that and not chatter and try to knock my teeth out like my current clutch. The closer to a stock clutch engagement feel the better, I hate backing up or starting out with a load more than 10k (I have to start in low, or 4wd low to backup). Truck is a 01 crew cab, on 35's stock gears may be going to a 6" and 37's in the future but that's it.
View 5 RepliesI am looking for a how to vid or resource on doing the job right. I purchased the complete replacement master cylinder from Napa. 2002 7.3 Powerstroke
View 3 RepliesI've tried everything I can think of to get my cruise control working again to no avail. I have a late 99 with a 6 speed. So far I have checked all the fuses with a multimeter, I've checked continuity from the harness under the dash through the clockspring to the switches, truck does not start without the clutch pushed in so the neutral safety switch works, has the upgraded switch and harness off the master cylinder. the previous owner said the cruise was intermittent about a year after they did the harness and switch recall on it. is there a way to test the harness and switch? I got a 1800 mile round trip coming up in about a week and I am gonna have a sore foot if I cant figure this out.
View 11 RepliesI just bought a 99 f250 super duty with 6 speed and it has clutch problem the clutch pedal goes about 1/3 of way down then drops to the floor and stays. I pulled slave cylinder and it has just as much resistance as a new one. my other thought was a spring internally in transmission. any other thoughts or do I just need to replace the clutch?
View 2 Repliessoo a friends 03 f-150 w/ the 4.6 has noticed the a/c compressor clutch engaging while heater is on. clutch engages for about 3 seconds or so and kicks back out consistently but only w/ the heater on. a/c dose function property when using a/c functions... Is this normal or does something need serviced???
View 3 RepliesSo that's what if feels like, in park at idle it sounds great, starts great no codes. IF you floor it it will not go over 3000 rpms in park, it feels like it has hit a rev limiter. I have 60psi fuel pressure at idle and at 3000 rpm.
When driving down the road I won't go over 55 mph and drives normal if you keep it under 3000 rpm, if you give it more gas it falls on its face?
AC is not working (clutch not engaging)I don't know if that's related or not.
We did just swap the motor the truck is a 2003 2wd drive. motor came out of an 2002 4wd. we are running the 2wd harness, computer egr delete etc.
Got in my truck this morning and everything worked fine, no problems. Arrived at my destination and parked. Come out about two hours later start the truck and my A/C wont blow air, My truck is an 05 lariat so it has the climate control A/C. Everything was working fine it just wont blow air, When i turned the A/C on and off i could hear/feel the small thump of the clutch engaging on the compressor. I am thinking the blower fan just went south? or maybe something stupid that controls the blower fan? Summer is in full swing here in central florida, temps are 95+ not including the humidity...
View 14 Replies