Ford 7.3L Power Stroke (1999-2003) :: Clicking Noise Coming Just Forward Of Chain Section Of Transfer Case
Apr 17, 2016
I bought a 2000 Ex PSD 4x4 in september. I have refreshed the suspension in the last 4 months; leafs, shocks, etc. I developed a vibration over 50mph after I installed the suspension and have been chasing it since.
I have replaced the U Joints, professionally balanced and lubed driveshaft twice, adjusted driveshaft angle to less than 1*, replaced the flanges for the TC output and the driveshaft companion flange. I have not touched the diff, but there is no decernable play in the pinion or leaks. Also, I removed the rear housing of the TC and replaced the output needle bearing and seal 2 weeks ago.
The output of the TC still has 1/4" play and a clicking noise coming just forward of the chain section of the TC. I assume the play is coming from other bearings on the main shaft in the TC.
I am about to purchase a remanufactured TC, but before I do, I need a reality check. Is it possible there is damage to the output bearing of the Transmission or something else?
I don't want to buy a TC to put in and experience a TC failure again in a short time. It doesn't make sense to me that there would still be so much play after changing the output shaft needle bearing of the TC if the TC main shaft is supported not just from the TC bearings but the output of the transmission unless there was possible play in the output of the transmission.
View 11 Replies
Advertisement
I have this 99f250 and it has a 273f, the transmission side of the case has threads stripped so I am about to remove and retap them. While its out should I consider rebuilding this thing? 197k miles, operates decently although the rear bearing on output side is my first thought to replace from mileage only.
View 1 Replies
Do we need to drain the fluid to change the transfer case motor?
View 3 Replies
I have a 03 Excursion 6.0 that just developed a transmission leak between the transmission and transfer case. It appears to be the transmission because the transfer case fluid is at the top. I started to notice transmission fluid leaking in my driveway. I have not had any driving issues with the transmission but I am not driving until I correct the problem. If this is the rear transmission seal, how had is it to change this seal? Must I remove the spacer between the transfer case and 5r110 tranny? Any special tools needed?
My temps have stayed at or below 150 if I recall. My fluid is slightly low in the transmission at about 134 operating temperature. The fluid is clean, red and has no burnt odor. My transfer case is topped off. Fluid ran out the fill plug when I removed it.
There is an aluminum square spacer than necks down. It is about 6" long between the transmission output on the excursion and the transfer case. The leak I see is where that spacer meets the transfer case. I see enough for the fluid to leak onto the cross member and to the driveway. I estimate that I have lost less than a 1/2 quart of fluid over a couple weeks.
View 7 Replies
I am completely stumped. 4.0 SOHC 145k miles.
There is a clunk that is coming from the transfer case (at least thats what it sounds like) when im driving in A4wd. When i transfer it over to 4HI, the clunking goes away. The clunk happens on acceleration AND deceleration. I have replaced wheel hubs, upper control arms, stabilizer end links....
Checked every other piece of rubber or bushing or connection or CV joint under that thing and can not figure it out.
Also, I just replaced the transfer case control motor and the clunk is still there. Its worth noting that I am able to switch between A4wd, 4HI, and 4LO with no problems at all. I am getting ready to drive this thing into the river.....
View 3 Replies
I bought a 2010 f150 from the company I work for.... It had a blown front diff, when I bought it, I just put a complete front diff assembly and front drive shaft on it. Thought I was golden, but when I accelerate fast there is a slipping/ snapping noise which sounds like it's coming from transfer case area... Accelerate slow and steady up to highway speeds it doesn't happen. This problem only happens in four wheel drive.... what this could be!???
View 4 Replies
I've got sort of a howl going on, was thinking rear end, but when i jacked up the wheels and spun the driveshaft the noise seemed to come from the transfer case area. I haven't had a chance to check the fluid yet, could it be a bearing in the t-case? Its only when i'm on the gas if i let off its gone. 2001 f150 super crew 4x4
View 4 Replies
What is the correct way to clock the transfer case so it will line up with the new transfer case shift motor. I have read that you should not clock the transfer case shift motor.
View 8 Replies
just bought the truck first time out hit some snow and it was not engaging low or high range, but I noticed that when I was backing up it was engaged again works in high and low range, i had to reverse about a mile up the road but it worked ? 99 4.2 standard with manual shift transfer case....
View 1 Replies
2001 F250, 7.3L ... After much diagnosis, I've found that the 4 positive feeds to the transfer case relay base have no power to them. The fuse that feeds them (#17 CJB) is fine and when I jump from the fuse hot side directly to the transfer case motor contacts on the relay base, it shifts fine. As far as I can tell, there is only one wire leading from that fuse so there must be a junction block somewhere that splits it into the 4 wires that feed the relay block. I've looked underneath and found nothing. How the 1 wire gets split into 4? On diagrams this junction point is labeled, but I don't know where to find that.
View 2 Replies
Truck is an 03 F350 with the 6.0. It sometimes sounds like the shift motor on the transfer case is trying to engage. It has the vacuum system which is blocked off. Warn aftermarket hubs. Switch on the dash with 2wd, 4wd and 4 low.
It's kind of an off and on thing. Try to engage for a few or more seconds then nothing for awhile then repeat. It sounds like it's at the transfer case. It could very well be coming from firewall/engine bay area as well. Is there anything between the dash switch and the motor?
View 2 Replies
My '91 Ranger 4X4 has developed an odd rattle that sounds like it's coming from the transfer case. It seems to be pretty much the same whether the truck is stopped or moving, or in Park or Reverse, or in 2wd or 4wd or Low Range. I hear it when the engine is just idling, with the transmission in Park and the parking brake on. It seems to be getting louder. I have the 4L V-6 with auto transmission.
View 2 Replies
So my '01 E350 has been fine but tonight when I went to start it I didn't get a WTS light and the SES light was on and there was a weird number on my PHP Hydra that looked like r5 ? This happened a few times back to back so I tried starting it and it just cranked and cranked. Wtf? So I started pushing the button on the chip and all of the sudden I got the WTS light and the hydra flashed, now the chip was on tune 10 instead of 5 where it was when I parked it. I should also note that during these episodes there was a fairly loud clicking/clunking sound coming from the drivers front under the hood when I toggle the key on.. Sounds like maybe a relay? Louder than I recall ever hearing.
View 5 Replies
I have a 7.3 Excursion, 234K Miles, 4R100 Transmission. Today I was in a rush to take one of our dogs to the vet, when I hit overdrive going up a hill, it almost sounded like a clicking noise and I was steadily losing power. I came to a stop sign and put it in park and it started to develop a constant lope that was rough. Whenever I would step on the gas it would put out white smoke which it has never done before. I was able to take it a couple miles before it did the same thing except this time it shut itself off.
Recently I have been having transmission issues as it feels im losing first gear. A while back I noticed it would idle slightly in park every now and then. A couple days before this happened, I came to a stop and my truck started loping slightly and first gear IN DRIVE felt very very weak. I have recently replaced the cam position sensor as well as the ICP sensor. I'm at a loss, I plan to do a ZF6 transmission swap very soon and this is only making me panic even more.
I never dog the truck, take it mudding, etc. Oil is changed every 3-4,000 miles. I did however get it scanned a while back and I believe two codes came up for two pistons, also did an injector buzz test and they all sounded strong.
View 10 Replies
2003 ex 6.0 limited....300000 miles ...Automatic.Merry Christmas to all.My Transfer case will not shift into 4wd . Dash light for 4wd high and low works .I get no power to transfer case 2pin connector when key turned on.Also fuses 19,27,31,33,34,45,111 are all good when checked with meter.I also swapped 2 relays in engine compartment and no change.4 WD Switch on dash has power on Green/red wire I think it is for dash light and not for operation.
View 13 Replies
I bought a new to me 03 explorer 4.6 tow package XLT 136000mi. Rebuilt aamco trans with 10k on it. Been checking it over before i put it on the road.. No 4x4 but the button lites work and i got into low range once. (Had a hell of a time getting back to high but eventually it did). Question is if there is 12v at the brown wire on the TC the case should be fully locked? I figure when i check it if there is not 12v at the brown wire in 4x4 high i could apply 12v directly with a jumper wire to see if the case locks to 4x4. Am I correct?
View 2 Replies
I just did an engine swap and have an odd noise that I was curious on where to start. It sounds like a buzz test on an injector at 2,250 rpm and gets louder as rpms increase but starts out very faint and get louder. Makes noise converter unlocked and locked in gear under load and free rev no load.
-2002 F550
-Fuel pressure is 60+ psi all the time
-Regulated return fuel system
-New injectors all AD
-Stock tune
-38R turbo
-New flexplate
-injector hold down tight
-new degas res
-new water pump.....
View 2 Replies
I own a 2003 E450 (transit bus conversion) with a 7.3L w/ California emissions. I recently noticed I have a considerable amount of oil in my air intake going back all the way to my turbo starting where the crankcase breather tube attached to the air tube. The breather seems to have some sort of filter housing that is attached to the top of the valve cover. I removed it and it appears to be fairly heavy as in if it's a filter, perhaps it's full. If I'm getting oil into my air intake from where the breather tube comes off that housing and joins in my air tube back to the turbo, could that filter or housing have gone bad? It appears to be a dealer stock item only for 225. I've saw on the web people posting "reroute kits" for the 6.0L but nothing for the 7.3. Does this part simply need replaced or could I be facing a separate issue as to why I'm getting oil in my air tube?
View 14 Replies
Took it in for the 10K service and squeak that started coming from under the treg. The said it needs a new transfer case.
View 12 Replies
I have a 99 f150 with a 4.2 manual with four wheel drive I need to replace the speed sensor in the transfer case it looks a lot like the one in the rear end I've called the auto parts stores and they show nothing. What sensor I can use ? I did find one on rock auto that said it was for the transfer case but after looking into there part I found it was for a automatic ...
View 1 Replies
My 97 4.6 ran fine but the 4x4 light came on even when the transfer case lever was in 2wd. Then one day it would not start. It cranked over fine but would not fire. I added fuel but it didn't work. I pulled a spark plug lead and attached a spark plug while I jumped the solenoid and cranked over the engine to visually check for a spark as I have done on older trucks. Well it cranked a couple of times and then it died and won't even crank now, I must've fried something, the batterys fine. If there is a fuse or something? What could have happened when I jumped the solenoid?
View 4 Replies
