Ford 7.3L Power Stroke (1999-2003) :: Check Engine Light On / Cylinder 5 Misfire
Sep 4, 2015
So when I bought the car, it had a check engine light. I had it checked it said cylinder 5 misfire. I assumed it was the glow plug so I bought it and replaced the glow plugs myself. Check engine light went away for about a day then came back on. Got it checked again and still said cylinder 5 misfire. This is my first diesel and I'm clueless as to what's wrong. Any way to check what's wrong myself?
Also just to double check, the cylinder number is 1, 3, 5, 7 for the passenger side front to back right? And 2, 4, 6, 8 for drivers side? And front to back means when looking at the front of the car? 2001 7.3 Excursion Limited with 232k miles...
View 6 Replies
Advertisement
I have a 2008 FX2 5.4L F150. Recently it began to lose power on a friend driving it out of town. He got a check engine light then it just progressively became unable to produce power. It ran but he got down to 10 mph before he could get to a firestone. I got it to a local Ford dealer and they say i need a new engine. They gave me codes for cam sensor and timing and #5 and #6 misfire. (344, 345)
No oil in radiator, no water in oil. The crazy thing is it runs like the day i bought it in Park. But once in gear it begins to cough and then eventually shudders and dies. I haven't changed plugs ever. I know... At about 75 miles it began to idle rough at times and in reverse. But once I revved up it went away.
I replaced both cam sensors but no luck. Today i put it on a tow truck to get a second opinion from a local engine shop. I actually backed it down my driveway, and pulled up to the tow truck with no issues. weird...
View 2 Replies
I have a 2003 ranger and have had ongoing problems with misfire cylinder six and have had three different mechanics diagnose the problem as a bad ground. I have replaced all plugs, wires, coil pack, injectors and am constantly pulling the plug on cylinder six, cleaning and often replacing, I also disconnect the battery so it resets the check engine light and it runs fine for about 100 miles and starts running rough again and on goes the check engine light. I have 134000 miles and have maintained it since new.....
View 4 Replies
I have a 2003 Chrysler Town & Country and the check engine light is on. I brought the van to my mechanic and he told me there was a code that told him there was a misfire on cylinder #1. He started out with replacing the wire to cylinder #1, no change. He replaced the spark plug, no change. He installed a new fuel injector, no change. The van runs a little ruff at idle and when at a stop light.
View 9 Replies
I have a 1999 Toyota Corolla. 4 cylinders.
I was on the road about 2 hours from home when my check engine light came on flashing. It stopped flashing so I kept driving. Three more hours of driving at highway speeds and it only came back on once. I then took it into autozone and the code reader told me I had a Cylinder 3 Misfire. The guy told me to change my spark plugs and I would be fine. It was time for a spark plug change anyhow so I drove home and did it. After I changed the spark plugs the car did not start at all. It would cough and sputter and try to start but not actually start. Changed the spark plug wires and then the car stopped even coughing and sputtering. It just didn't start.
I then noticed that my fuel line that feeds directly into the engine was rotten right next to the engine and if I pushed it in I could get the car to try to start. (Try and fail, but at least try.) The fuel line is a molded piece of rubber that flares at each end. It was one of the flares that was rotten and didn't seem to be sealing anymore. The hose is 7 mm inner diameter in the middle and about half an inch on the ends. I took some 3/8 in fuel line and used it to cover over one of the flares. The car tries to start now but wont. 3 of the four cylinders crank. I don't understand how I could break my car on such a simple repair job.
View 4 Replies
New to diesel trucks and wondered if this recurring code is a serious problem. I clear DTC and truck will run fine. Might stay off for 2 days or 2 months and same code comes back. Truck seems to run just fine even with service light on.
View 5 Replies
I put a 150 w converter into one of my 12-watt power female and all of a sudden when i turned the engine on my check engine light came on with 4 glow plugs bad and now won't pass smog. any way i can turn off the check engine light so it won't comes up on the smog test?
View 3 Replies
I bought my 2000 7.3L Ex as salvage back in 2005. It had been through a driver side rollover and the seller had restored it. We lived in North Idaho then. But I remember I always had an issue with the check engine light being on. I don't remember what the codes said, but many mechanics read them and determined that nothing was wrong. Many surmised that someone had put a high performance chip in the computer and that was what was causing the check engine light to come on. All of them reset the computer and every time it would come back on. Should I replace the computer?
View 14 Replies
1999 f250 7.3 101k California truck ... Scanned it said #1 glow plug did not clear the code. But now the check engine light is off again...
Questions : Harness issue ? Glow plug bad at 100k ? Glow plug controller ?
Start at glow plug work way back to GP CM or in reverse ?
Replacement Do all 8 or just the bank of 4 ?
Thoughts on replacement brands
Accurate diesel glow plug replacement kits any good, will they last ?
Or go factory glow plugs
What about Felpro gaskets
I heard about another brand of GP CM
View 14 Replies
2001 F350 290,000 no mods other than 6637, 2WD
Towed our new to us RV home last, only 15 miles from the dealer and yes its a big 5th for my truck at 12,000lbs. Anyhow, about 2 mins from home as I'm pulling off the freeway I got a SES light come up, then it disappeared. I checked codes this morning using forscan and nothing shows to indicate what it may be.
I was wondering if the transmission is getting hot if it throws an SES? It was only a short trip, but I have no real idea of the condition of the trans as the truck is new to us too - fluid looks and smells good.
Only new code is an ABS one c1229, c1233, C1234. I had 2 of them before - think the 1229 is the new one.
View 14 Replies
So when I bought the car, it had a check engine light. I had it checked it said cylinder 5 misfire. I assumed it was the glow plug so I bought it and replaced the glow plugs myself. Check engine light went away for about a day then came back on. Got it checked again and still said cylinder 5 misfire. This is my first diesel and I'm clueless as to what's wrong.
2001 7.3 Limited with 232k miles Bergen County NJ.
View 2 Replies
Now that I have been driving for a while I kept seeing this light come on/off and I did a video below - I don't generally flash my lights so don't think I am aggressive - but I wanted to make sure to capture the video and the light coming on.
I was thinking valve cover connection the 50 cent mod - and maybe it's all coincidental - but I did have to pressure wash the troph where the oil collects and maybe something else got knocked loose.
[URL] .....
View 13 Replies
I have a 2002 F250 4x4 Powerstroke with Automatic. I have been having off and on issues for months with the throttle going dead. This only happens when I start it, if it works when started it will continue working until a different start session.
I have replaced the pedal several times before learning how to check its output with a meter and am quite sure that is not my issue at this time. However, when the pedal is depressed the check engine light lites up and nothing happens.
I am thinking it must be the computer itself, but was told there is another sensor or module under the hood that could cause the issue also which is several hundred dollars to replace as would be the computer.
Is there a way to test the computer, and what is this other module/sensor if it exists that could be the issue? Unhooking and rehooking the battery to reset the computer is no longer working to buy me a few more weeks, is there a simple way to reset the computer to try?
I love this truck when the throttle works but I am getting tired of paying on a truck while having to borrow a vehicle to drive to work.
View 5 Replies
I have a 2000 f350 7.3 got a check engine light that turns off when rpms go up and a slow start. My mechanic said that there were no codes being blown, what is going on?
View 11 Replies
I have a 1999 f250 7.3 I was driving down the road today and I lost throttle along with my check engine light coming on. I pulled over and turned my truck off and now it will not fire back up.
View 6 Replies
I have a 2001 F350 with the 7.3 standard trans. The previous owner put a toggle switch to control the EBPV as an engine brake, I've never used it. It blows white/blue smoke when cold but has for the last 4 years and doesn't seem any worse now.
Last fall I ran the truck the lowest on fuel that I ever have, the light was on for a long time and I thought I would run out. I made it to the gas station and filled it up then drove home. The next time I drove it I went about 25 miles and it started to buck while going up hill. This got worse and eventually the check engine light came on and it stalled.
It wouldn't start again so I had it towed home. I got it started a couple hours later but it would run really rough and only for a minute or so then stall. It will usually start again once or twice and stall, then it wont start again until it has sat for an hour or so.
I didn't have a code reader at the time so I started reading threads. Here's what I've done to date.
Changed the oil and filter, it was way over do. New fuel filter.
The oil level in the HPOP stays about an inch from the top, I've checked it a few times after its stalled.
Dropped the tank and cleaned the screens in the pick up, no change.
The ICP had oil on it so I replaced it and a new connector, no change.
Changed the CSP with a grey one, no change.
Changed the IPR valve with one from a buddy that was on an engine that was running. The truck ran rough for a min then settled down and ran smooth. I let it idle for 20-25 minutes with no problem so I thought the problem was solved. After sitting for a month or so I fired it up and its back to running rough then stalling.
I bought a Vgate ELM327 connector and downloaded FORScan on my laptop. (I'm still not sure what I'm doing). These are the stored codes P1281, P0475, P1316, P0478, P0470, P1211. I cleared all the codes. I did a buzz test cold and the Injectors all sounded the same.
I monitored the truck while running (rough) the IPR is staying around19.92%, ICP is 701.4psi. After 5 seconds the ICP starts to climb and so does the IPR, at 12 seconds the IPR is 37.11 and ICP is 1835.1 psi the it stalls. The fuel pw,ms is around 2.50-3.0 until before it stalls, then its 1.66. The only codes that come up are P0475, P0470, B1473.
View 14 Replies
OK, got a check engine light today when I fired up the Ranger. Like I posted previously it is running kind of rough so guess I know why now.
Took it down and got the codes read it have a miss fire on cylinder 5. Picked up some plugs and wires, got to get those E3's out of there, but kind of think that's really not going to fix the problem. So that probably leaves the coil pack or injectors.
So what's the consensus on the best coils to use? Also, being an 18 wheeler for more years than I care to remember, I've learned swapping just 1 injector is never the way to go. So whats the best type of injectors to get and where the best place to get them should it come to that?
Oh, it's a 2000 3.0L Flex fuel 5 speed.
View 6 Replies
I have a 2005 f150 with 96,000 miles. Long story short, last August I was headed to the mountains going up a steep long hill and the engine light come on. once i was over the pass the light went off. During my 4 wheelin' trip it never came back on until I was headed home and going over another pass and then it stayed on for a couple of days. I had it checked and it was a cylinder 5 misfire. I did some research and found that replacing the coil cover might fix the problem and if not the spark plugs would need to be changed.
I changed the coil cover, problems solved... until I headed to the mountains. light came on and then eventually went off later that day. I didnt think much of it. then a few months later i was headed to the mountains again and the light came on in the same place on the steep incline hill. I. took it back to the shop, same reading. I decided it was time to replace the spark plugs anyways so I would invest. I have new plugs and everything is good however, I had no plans to go to the mountains in the near future. Now, a few months later I headed to the mountains and crossed my fingers it would not come on but it did.
I've done the research again and it seemed like the coil cover and spark plugs are usually the cause of the problem...however I have changed mine. The light is now off again. I don't understand what is triggering the problem and what is really happening and if it is safe to keep taking to the mountains with this happening. I did notice that everything was fine at 60MPH but once i hit the hill and steeped on the gas to go 65 and hit 4-5RMP that is when the check engine light came on...
View 12 Replies
1997 Ford F150 - 133K Miles - 6cyl - 4.2L. This is a truck that gets less than 2K/year put on it. Has had "issues" with worn bearings and holding oil pressure for a few years now. Yesterday, the check engine light started flashing (as opposed to solidly lit) and the code came back as a cylinder #4 misfire (only the one code). The truck was clearly not firing on all cylinders and at idle, ran terribly (couldn't be driven). I just did a compression test on all the cylinders and all measured around 140-145psi except the #4 which read almost 170psi. I rechecked this a few times as well as a couple of the others and am now sure of the results. What could cause this one cylinder to have a higher compression ? Is whatever is causing this increase in the compression, also be the cause of them misfire ?? I'm stumped here and quite frankly, expected the compression on the #4 cylinder to be really low as opposed to the others.
View 13 Replies
2002 F350 7.3 PSD. 192k miles.
From my understanding, a CEL is supposed to illuminate each time you turn the ignition ON as part of normal startup procedure.
I figured the previous owner must have pulled out the bulb to hide the fact that the truck had a few "issues" before selling it, so today I pulled out the gauge cluster and it looked as if the CEL bulb was a tiny LED soldered directly into the gauge cluster itself. There were a few serviceable/removable bulbs for things like turn signal indicators, high-beam etc... but the CEL did not have a serviceable/removable bulb.
I've been driving this truck and working through it's "issues" and fixing things as I go, but it keeps throwing codes without the CEL illuminating. What's going on here?
I thought the check-engine-light was supposed to illuminate each time the ignition was turned on, and that it would come on each and every time the vehicle registered a fault code in the ECU/PCM.
View 14 Replies
I'll try to break this down as best I can. I went to my mechanic this am with a check engine light. My suspicion is 02 sensors. This was confirmed as a problem area, but separate they said I had a spuratic misfire in cylinder 4. With that info, i pulled the plug to inspect (I had just installed new ngks in it and they have 18,000K on em.
I put beldon wires on about 8k ago.) plug looked to be normal, but there was definitely a puddle of oil from the valve cover leaking. Oil went into the cylinder head but I didn't really think that was an issue. Nothing abnormal jumped out at me so I reinstalled plug and checked all wire connections at both ends and called it a day.
Then I drove it. Check engine light flashing. Major performance stutters, etc. I drove it for about 20 miles and hoped it was just the oil raising hell in there and it would burn off eventually. It hasn't gone away yet. Maybe coil pack. Can the single portions of that pack be replaced, all i see them sell is the full three as a unit.
View 7 Replies
