Iv heard a few things about changing the valve body. I tow a trailer so was wondering on pros and cons of changing this. And also what brands are recommended.
View 5 RepliesAfter running highway speed then stopping, the EBP valve is partially closing as you accelerate back up to speed. You can hear it in the sound of the motor, and you can see it on EGT's, which are rising quickly. This happens briefly then corrects. We unplugged the EBP sensor and the problem continued. Tube is clear.
If I monitor the EBP sensor, what values should I see if it is functioning properly?
Have to get rpm's over 2k before trans will engage, then in between shifts I either have to let off throttle or let engine rev over 2k to get trans to shift...
View 3 RepliesI'm getting a sound every now and then of what sounds like i'm running over rumble strips on the side of the highway. I'm guessing it's the trans grinding. Any thoughts?
View 8 RepliesI notice my trans temp gets really hot fast. For instance just moving my trailer from front of my house to side yard makes temp go to 250. Without any load and driving a couple miles it does the same thing. It's been doing it since I installed the trans temp gauge just trying to figure out what's up.
View 14 RepliesI bought this truck with 200000 miles and its been flawless, its now 900 short of 600000.. I use it to haul everyday.. nothing heavy mostly a car or truck and every once in a while a skid steer. I got 560000 out of my trans, i take it easy. lol
at 350k I installed a Jw valve body drilled pump, tripple disc converter and solenoid pack.. at 560k it went, i pulled it and brought to a guy i trust as much as you guys trust BDS.. Ive had what Ive called a vibration since day one, could be a shudder, could be a shimmy.. what ever.. I brought it back and he says nothing would do that from a trans, so I went through drive shaft, new t case ripped apart rear end and its still there and I have just been dealing with it.. about 2 months ago it started acting up in first. when I pull down to drive I get the normal bump and start to go, it feel like the truck slows, then another bump and it climbs normally with the shudder.
took it back and he said maybe a stuck valve in small VB, so I pulled it and went down there and it was fine, I reinstalled and still does same thing. I then put a pressure gauge on it and it swings as it should sits around 70 psi and will climb, only in first it will climb and fall back to 70 like a switch was flipped, and the rest of the gears bleed off slowly or normally.. He then said it could be the big valve body, so I swapped that one out with another and no real change, maybe its a bit more noticeable.
I am at a loss. Could this be loose feed bolts? Could the shudder that I can feel at most speeds be the 1 gear slipping a tiny bit all the time? I am told that first gear is always on.. this truck has been a dream until this trans issue..
I've searched, and gone back through my computer history and can't find it. I have seen a thread here which Mark contributed too which said what the max temps were and for how long etc. I know book is 230 and optimum is around 165 but there was some degree of play in that.
View 8 RepliesSo I just put billowed up pipes and changed the broken O ring in the turbo housing. Put everything back together and checked for a boost leak with the home made tester. Boots and everything ARE OK. I can hear air escaping from what seems to be the valve cover or intake. I realize that I am charging my crank case as well but it still concerns me that air is escaping from somewhere besides the CCV. I read the following forum and this guy had the same issue and after he found out he was charging his crank case he was no longer worried. . . . .
View 12 RepliesI just had my turbo and the EBPV on the pedestal rebuilt. Now I need to put it back into the truck. What is the procedure, if any, to adjust the EBPV? I only use the truck to haul a 5th wheel RV and the performance chip closes the EBP valve when going down steep hills -( EXHAUST BRAKE)
View 6 RepliesAfter checking my fuel bowl today for contaminants, I put the lid back on and then noticed a leak from the rear at drain valve. I know, I already ordered the orings. It was doing one drip about every three seconds with the truck running. However, I turned the yellow thing a couple times and the leak stopped. Not leaking right now. Maybe it wasn't shut from previous owner.
Second question.....After stopping leak and after routing my fuel drain hose, I decided to give it a try. No luck. Nothing out or drain. Based on my first fuel filter change, it may be clogged up. So, do I run wire from the bottom up? Or do I run wire from top (bowl) down? Just so you know, sucked the bowl dry with a vacuum device before I reinstalled the filter.
doing injectors and pulled the valve cover, and noticed its not as clean as i expected. in the oil on top of injectors i noticed its got some grit in it. this cant be good and not sure how this debris got in there as i always change oil and air filter regularly( unless previous owner neglected). is there a safe way to clean this? Is this a normal find for you guys that have done injectors?
View 1 Repliesmy first diesel, and second 2002 f250. I picked up my 7.3 4x4 automatic CCSB last week. 202k on the odometer. I need to change the air filter but idk what to use. I don't think it's stock. The side of the air box says aFe. What the part number for the filter is? I don't see one on the filter anywhere.
View 6 RepliesSo my transmission drove perfectly fine I just wanted to put an upgraded torque converter in especially after driving a customers' truck with a low stall converter. I know their not like for racing or anything but it's a work Truck with some mods to the motor nothing crazy. So I went ahead and bought a low stall triple disk converter and I drove around the block fine and went to go on the freeway and got into fourth but lost it as I hit 75 (was not flooring by any means and had it in the stock tune) now it will not go past second gear. Once it did this the o/d off light started to flash and I decided to do a stall test.went to 1800 in a Second. Suppose to stall around 1200-1300.
2000 f250 7.3 powerstroke dp chip stage 1 camshaft and 180/100 injectors coming at some point but stock for now
Well stock trans went two weeks ago so warranty company had another stock one put it (4r100). Finally got the truck today and I noticed my overdrive was flashing. I have no issues though shifts fine speedo works Rpms are normal I checked fuse 19 under the dash that's fine so I'm lost
If I turn the key on I can use the button like normal but once I drive it just flashes. It works but flashes .
So just got a new pcm installed since i fried the last one anyway. I had a new trans installed almost two weeks ago factory 4r100 now i have a p0720 code. Id take it back to that dealer.
View 8 Replies1999 7.3/4r100 4wd with the rattling torque converter.
I bought this truck 10-11 years ago to use as a tow rig for my landscaping company. It has been a great problem free truck, I have done brakes a few times, a water pump, ball joints but no issues with motor/drivetrain.
I don't know the history of the trans before I purchased. Ford didn't have history of it being replaced and even now it still has all the labeling on the case. I would have thought it would have been washed off in a rebuild. Again I don't know. When I bought the truck it shifted nice and crisp, having owned trucks before it made me think it had been rebuilt but this was my first and only 4r100. Other trucks are ZF6 manuals.
Anyway 10 years and 100,000 miles later it still shifts very crisp and fluid, has been changed a couple times, is nice and cherry red. I added a 6.0 cooler, temp gauge and filter. Never see the temp rise and haven't seen much in the filter.
About 25,000 miles ago the TC started to rattle, a known 99 problem. I figured surely the trans would go and I would do a rebuilt from Ford. It keeps going though so being a work truck I have kept running it.
A couple weeks ago the starter just spun and wouldn't engage. I pulled the inspection cover and noticed some missing teeth on flex plate. Got it to start my turning crank bolt a bit to good teeth and the starter caught. Now we are carrying a breaker bar and socket. It has happened a few more times so I need to replace flex plate.
Question is, since I need to pull trans to replace flexplate, should I replace TC (I would like to get rid of the noise)? Some people have said I will be replacing trans in a couple months if I mess with it. They say just spend $3000 on a rebuilt now with a converter. Not trying to be cheap but hate to just dump this trans that is still working great and has served me well.
I have replaced many transmission and done clutches in many trucks so I am familiar with the steps of removal and installation, just stuck on what I should do.
2001 7.3 auto, 2wdr, 291,000, Transmission sometimes shifts hard from 1st-2nd, 2nd-3rd. Problem started after I found trans dip stick tube broken and loss of fluid. Anything I can do without going to a shop. I've replaced the Broken Tube.
View 2 RepliesThe bolt that holds the dipstick on the valve cover. i have tried for ever to get this thing off. soaked it , got a skinny wrench on the nut underneath but think it might be stripped (1/2 inch grinded out a little). going to try and get a set of skinny wrenches tomorrow , mine bent. tried vise grips on top of the bolt and put a box wrench on the nut , and gave it my all. The damn thing won't budge.
Also, any tips on the rest of the valve cover bolts. I had to remove some from inside the fender well but barely got to them. My question is not getting these out but getting them back in. And how the heck to you torque these things??? The bolt i mentioned above is creating problem, and I only have so much time
I have what might be a big problem, the main harness on top of the drivers side valve cover I can't get undone, the bolt holding it together is stripped or the nut who knows? wondering if there is any way to take it apart otherwise.
View 11 RepliesI have a late 99 7.3 that developed a knocking noise. I pulled the passenger's head and cylinder 5&7 have a spot where it looks like it came in contact with the valve. I'm not some master mechanic but am learning. What would be my next step to find why it hit the valve and to fix the problem?
View 14 RepliesI am changing the rear Diff fluid in my 1999 F250 Super Duty with limited slip differential. I have read in the manual that 8 ounces of friction modifier is required, ford dealer said it only required 4 ounces. I bought 8.
Also I asked for a inspections plate gasket and ford said use silicone... When I removed inspection plate it had a gasket. So, silicone or gasket or both? Differential capacity is 6.9 pints 75w/140w synthetic.