Ford 7.3L Power Stroke (1999-2003) :: Can't Drive - Sway After Leveling Kit?
Apr 28, 2017
So I went from a 3 inch to a 2 inch leveling kit. After tightening everything up the sway bar was a hair off. I pulled it out of the garage and got it lined up. Fast foreward the next day and went on a 200 mile trip hauling an empty goosneck and noticed it one time. The day following the the truck has went into this horrible sway through the tires back and forth that makes it undrivable. Looking at tie rod ends the one at the pitman arm is shot. I order the whole front steering kit from xrf and I'm going to replace. I know I also have some play in the box but I have for awhile. So what else would there be to look at? I need to get this fixed. I will update after the steering is put back together.
View 9 Replies
Advertisement
So putting the new extended links on my truck, not sure if they are supposed to be seated flush on both the frame and sway bar itself before tightening them down. This is how they are sitting now --
You can see a little gap between the rubber fitting where the bushing sits and the frame mount. Just wanted to make sure before I torque it down. Its the same on the other side as well. They are sitting flush on the sway bar.
View 1 Replies
I have been having that nice thumping noise that generally accompanies worn out sway bar bushings. I did bushings last spring but a noise came back shortly thereafter. Finally got bothered enough/ found enough time to take a look at it and tracked it down to the sway bar again. My right front axle mount has taken damage before and is now all bent up, not allowing the bushing clamp to hold tight to the bushing. Pictures of the issue are below.
Front view of the entire mount.
Rear view showing the sway bar mount plate.
I am unsure what to do about this mount. As you can see it has been pretty messed up by the PO. What could be done to fix the issue?
View 4 Replies
My tranny is acting odd. I put in drive and seems to slip a lot in 1st, barely even move at some times. If I put it in 1st with the shifter it goes in and grabs then I can shift up to 2nd or drive and there aren't problems. It drives normally when not from dead stop.
Transmission has 50k miles on it since replacement. Fluid level is normal. I don't tow and drive it particularly hard. I will have to go back and look at miles since last fluid change. I should be right around 30k miles since last change.
View 11 Replies
What is the difference in drive/ fan belts with Cold Weather package and W/O cold weather package? As I have been trying to figure this out at the Irish part part it says for a single alt ....
Cold weather package the Outside Circumference (In): 121.900 and
Non cold weather Outside Circumference (In): 122.735 Inch
View 14 Replies
Tranny rebuilt, truck in sig, and beefed up 2 1/2 years and 30K miles ago. Recently started going into D after 10 to 20 seconds after putting it in gear, cold or hot. Very frustrating, especially when trying to maneuver a trailer.
Transmission builder has been running his shop for 20+ years, all makes and models, not Ford specific. I choose him because he runs a local business, has a good reputation, and happens to live less then 1/4 mile from me.
I have searched the forums, and read where Mark says this is loose valve body bolts, or forward drum going out. Builder can't grasp where it would be drum seal if it doesn't do it all the time, which it doesn't. He said it sounds more like something electrical, but there are no codes stored on pcm.
Builder also said he would pull tranny to check drum. Does this sound like I'm moving in the right direction? Or can it be something else?
View 6 Replies
I guess it would be classified as very intermittent but in the past year I have had 3 separate times when my truck has after a short drive suddenly had zero boost..
Pull over and turn it off for 30 sec or so and all is fine. Cycle the ignition faster than that and issue persisted. It has only happened in colder temps. In all the reading I have done on FTE I've not come across anything similar.
View 14 Replies
Driving along today my trans started doing some weird stuff. It lost all gears. Forward and reverse. If I turned the truck off and let it sit a while it would go again for awhile then loose drive again. When I got home I checked fluid level and did KOEO o/d off and back on. I drove it around the block and it seemed ok, so I went on my way. After about 20 min I noticed the OD light flashing. I checked codes and It had P1754-ccs.
View 14 Replies
I bought a 99 7.3 been in the trees for a few years pulled it home and now trying to get it running. Did a service new filters and oil fuel too. I can get it to start and will run but runs very rough and if you put it in drive cant pull its own self. I don't have a check eng light on. And found out my scanner is a pos lol. it will hooked up and then try to pull codes and loses it connection. But that's the scanner will not work on my other 7.3 as well.
I am making high pressure oil checked off the rail with gauge and it will build up to 2000 psi when I rev it. but missing like crazy. I swaped the pcm and idm out of my running 7.3 and it didn't change a thing. I have checked the pass though and they are fine. pulled drivers side valve cover off and no oil leaks when running and rockers are fine. new ipr valve as well too. I know I need to get a scanner to talk to this thing better.
View 3 Replies
I got a 2000 f350 7.3. Cranks up fine runs fine put in reverse and can back up fine put it in drive and it bogs down and dies. What is causing that.
View 2 Replies
I have a 2000 Excursion diesel 7.3. I drove it for an hour yesterday and it drove great. When I arrived home I left the truck running and put it in park. Checked the mailbox and jumped back in the truck and put it in drive and it would not move. Tried FWD and reverse. Moved a little in reverse.
I turned the truck off then cranked it back up put it in drive and it drove fine..... Took it for a test drive and seems fine.
Did the same thing today. Went to drop my kids off and I put it in park and left the engine running. Put it back into drive and it would not move.
Turned the vehicle off and back on. Put it in drive and it drove off fine.
Fluid is full, red and no burnt smell. Wondering if this is converter or electrical and how long I can drive it like this.
View 1 Replies
I have 1996 Ford F-250 that I just put a axle in that came out of a 2003 Ford F-350 this week. I test drove it today and my locking hub fell out of the driver side. I looked for it but couldn't find it. I drove home and the ring fell off of the passenger side from driving it back but the hub hadn't fallen out yet. what can I do to keep the hubs from falling out
View 6 Replies
What Spicer Part #s for the rear u-joints would be? I'm not nailing down the right one. I keep finding numerous ones, 1410, 1350, 5-160....
View 8 Replies
Ok, the swap is all done and I have an engine in the truck that has compression in more than (7) cylinders.
2002, 7.3, 4wd - ~120k miles on trans. Fresh fluid (Mercon V).
Put the gear selector in reverse and it goes right into gear with the normal tug and functions as it should. Put it in low gear and it also appears to work fine. But, when selecting '2' or 'drive' it feels almost like its engaging 2 gears at once?? There is limited forward motion and it feels like the brakes are on. I have not driven further than the driveway yet, but I have a long driveway...
The OD light does not come on. I am not getting any codes from AE, but I really don't know how to use it for transmission stuff (I've been using a different scan tool that I no longer have).
We have not put the bed on the truck, so no tail lights - but 3rd brake light has new bulbs and was working (didn't check this AM though... )
I have a couple other codes, CEL, 'check gauges' and no tach. Gonna start another thread for those issues, I'll put a link here in case its related.
View 14 Replies
I have a 2002 f350 7.3. It was running fine 2 days ago. After I put some diesel in it my water in fuel light came on. I drained the water out and took all the fuel out and put fresh diesel in it. It starts up fine and idles okay but when I try to drive it it looses all power and acts like it's starving for fuel and almost dies. It was smoking white smoke for a little bit even after I took all the water out but now it's black. What it could be.
View 9 Replies
I have 2002 F250 7.3 Auto, I recently tried to put my truck in to 4 wheel drive and it is not working. It has WARN manual locking hubs, which I locked. Dash indicator came on and I can hear it click on the transfer case. Yet it isn't driving the front tires. It shouldn't be a vacuum issue considering it had been converted to manual hubs should it?
View 5 Replies
My rearmost drive shaft u-joint is bad and has slop. I've been having vibration for about 7-8 months, but just started hearing a noise within the past week, especially when taking off with a load on the drive line (uphill or heavy acceleration). The vibration has not gotten worse, just that the noise has just begun to show itself.
I have one u-joint which is OE and has 275K miles on it, and it seems to be OK at the moment. The other two (including the rearmost unit) both have about 100K miles, as does the center support bearing.
Just because I don't want to worry about anything, I'm going to replace all three u-joints with Moog Super Strength units, and will also replace the Center Bearing with a new Spicer unit... just because I can and don't want to be pecked to death with multiple failures in the same drive line. I ordered the Moog joints because the only Spicer joints I could find were for the 4wd configuration.
That's the context... here's my question... The parts are on order and won't get here for several days. I've been driving the truck like it is at about 1500 miles monthly. Do I continue to drive the truck for another week before getting the joints and bearing installed? I know it's a guess... just looking for more perspective.
View 14 Replies
My spine was damaged in an IED blast in Iraq a few years ago and my truck is getting harder and harder to drive. It sends every little bump up me. It looks like I have the original shocks on there.
What is recommended for shocks or possibly seat upgrades or any other possible solutions. I love my truck and don't want have to get something else.
The most I haul is my jeep on a trailer and occasionally two jeeps (8000lbs)...
View 9 Replies
This is wife typing in middle of trip. Today we drove almost 300 miles down the road before it stuttered. We lost the tach but nothing else. No check engine lights. It has done it a few times since. Watching with Torque and don't see anything there. Have 100 miles to go and it's happening more frequently. Replaced CPS 4 weeks ago with a Ford grey. Running down road it's 95 day. Oil was checked to be good at 211, transmission 182, EGT 790, pulling enclosed 6x12 cargo trailer. What can I check?
View 14 Replies
Just happened today right after I bought diesel. thought it may be water in fuel but after researching wondering if it is injector, etc. It starts every time knocks real bad sometimes for a minute, but clears up to idle ok. During idle no smoke, slightest acceleration however produces white smoke harder I accelerate more it plumes and it smells like diesel in the air.
Cannot get past 15 or so mph till switching into 2nd gear then 25mph max. Had to drive 4 miles like this I can say it cleared up and drove 1/2 mile until I had to stop at a traffic light then going from idle to acceleration again ran bad rest of way home another 2 miles.
A few years ago I did have a rough idle and accel. similar and it ended up being the broke pick-up/sending unit in tank (but of course that was when you get to around 1/4 tank of fuel and didn't run bad above that much fuel in tank), plus there was almost or more than a gallon of water in tank. I have done the mod for the fuel pickup with hoses, filter canister, etc. but wondered at first today if I had gotten bad gas or water in the tank again. Not sure how that much water got in the tank to begin with but that was bout 5 or 6 years ago.
Truck has over 200k miles and Ive had it for 11 years. In the morning will check the ICP sensor by unplugging look at fuel filter bowl, etc. A question I have is: Is water heavier than diesel, would it run thru my line first? thinking diesel is heavier than gas because of oil content....
View 2 Replies
I have a 2002 7.3 e350 quigley 4x4 Sportsmobile with 312k miles. 2nd owner. Bought it with 295k miles 2 years ago. From what I gathered the tranny is original.
After reversing at a downhill angle, stopping, and shifting the lever to Drive, the tranny doesn't seem to put Drive in gear and depending on the angle of the slope, the van will roll back or barely creeps forward even with throttle. Put it in 1st gear, and the tranny engages that in gear and drives forward no issues, then I can shift to 2nd, then Drive and the tranny shifts fine after that.
No weird tranny noises or clunking. Noticed this issue about a month ago or about a couple thousand miles ago. Did tranny service (drain, filter, fill) at the ford dealership at 305k months ago.
I can only replicate this issue when Reversing on a down slope. On a flat surface van Reverses and engages Drive like normal.
View 7 Replies
