Ford 7.3L Power Stroke (1999-2003) :: Battery Light On / Voltage Meter Only Show Barely 12 Volts At Full Throttle
Jun 14, 2017
The brief information:
1. Stuck/non moving in traffic on the freeway for roughly 1 1/2. During that time the AC was running, but once I noticed my "battery light" on the dash turn on, I turned everything off.
2. Since then while on my way home from work the voltage meter only showed barely 12 volts at full throttle.
3. I charged my battteries, and started it up today to go into work. While going to work the voltage meter showed 14 at its high point, but shortly there after it dropped back down to 12. At which time the battery light came back on.
New battery or alternator?
View 1 Replies
Advertisement
Bit of a confusing one as of late. Doesn't happen every time I drive, maybe 50% of the time. When I start the truck up, torque pro reads voltage at 13.9-14.1 consistent. After 30 minutes it usually drops to around 13.7/13.8. Sometimes, battery light comes on, voltage doesn't drop. I can drive the truck, park it, turn it off, restart, no side effects.
I notice if I stop, turn off the truck, and restart it, torq pro will begin to read a voltage of 12.8.13.0. Sometimes it won't budge for an hour, sometimes it climbs right back up to 13.8, sometimes the battery light goes off, sometimes it stays on.
Alternator was replaced a month ago, both batteries replaced a week ago, all terminals cleaned and secured at the time of replacement. Truck behaves perfectly normal, I'm almost at the point of putting a piece of tape over the light and ignoring it, but was curious before I go that route.
View 3 Replies
2002 Ford Windstar: Whenever I disconnect the battery and then reconnect it, I get this hum that sounds like the CD player preparing to play a CD. There is no CD in the player. It last for about 30 seconds and then stops. Afterwards, my check engine light comes on and stay on until I have the mechanic reset the alarm. The battery is new. My meter shows that the battery is giving out enough volts. It annoys me to have the check engine light on all of the time. I'd rather it be off so it can report if something else goes wrong with the engine.
View 1 Replies
I do run a small battery maintainer during the winter months plugged into a three way with the block heater. Alright after sitting out side for approx 9-10 hrs in 22 degree weather I did these checks. Battery voltages at 12.55V and 12.6V on batteries.
Voltage coming into for was also 12.5V. When glow plugs activated I am getting 11V on the other side of the gpr. After cycling glow plugs battery voltages drop to 9.6V during cranking and as soon as she starts back to 12.5V.
Do these numbers sounds right? In my opinion isn't the drop to 9.6V during cranking a little low or is that the normal?
View 14 Replies
So when its cold and im talking below 55 degrees, and the truck hadn't been started that day, it will turn over 3 or 4 times before the voltmeter takes a dive down to 10 volts or so and doesn't start. The voltage will keep falling if cranking continues. I took the batteries out and had them tested. They are both above the rated cca. So im thinking it could be the starter windings?
I did replace an injector recently so all the cranking to get it going again may have ruined the starter? But when I hook up the battery charger and jump the truck it starts. And after it has been started it will continue to start easily the rest of the day.
View 9 Replies
2000 Ford 7.3 E450 120,000 miles...
I have changed the CPS twice
I have checked the resistance of the injectors at the IDM connector with a volt meter and the harness reports back good.
The truck will run with ether for a few seconds
I have changed the fuel filter.
The fuel bowl fills quickly
I have unplugged the ICP.
The truck is showing low voltage on the gauge with a good battery. Around 10v
I have connected my 200amp car starter and I never see over 10v. I plan to check the grounds, but I am at a loss.
Everything is difficult because this is a van body so space is limited. I have also plugged in the block heater for an hour and that hasn't made any difference. Where can I get the best price on an AE scanner.
View 14 Replies
2003 f250 6.0.... recently did oil cooler,hpop,ipr,icp,fuel pump,egr valve, rebuilt the turbo.... when around 35mph truck seems sluggish and doesnt seem to pick up quick untill i floor it an then hauls butt.. vgt reading at idle is 62% and when floored around 30 to 35%.. fuel pressure is 63psi.. ipr is around 60 to 70% when floored and around 25% at idle. Hpop reading when floored is 3000 to 4000psi and idle is 624psi....
View 14 Replies
My Battery light came on on my dash and my scangauge 2 was reading 11.5/11.4 volts yesterday afternoon, I ran for codes on my obd-2 and P0528 came up. I picked up one new battery and put that in to see if that would bring my voltage up at all. Today it was reading 11.3/11.2 volts. From what I've gathered the P0528 is most likely the fan clutch or the harness connecting the fan clutch to the PCM.
I've seen the water pump replacement write up that shows how to pull the fan assembly. My questions are - can the fan clutch be replaced without draining/pull the radiator? or is it better off to just do the coolant flush and pull the radiator. And would the fan clutch/harness issue drop the voltage or would that just be two bad batteries?
View 7 Replies
After installing new glow plugs, glow plug relay, and valve cover gaskets my 2000 7.3 is throwing the 1395 code. Glow plug monitor Bank 1. Any input as to cause? Checked all connections to relay. All tight. Read something about fusible link. Where that is located? One side of relay reads 0 volts.
View 4 Replies
Another thread on here about Time for Batteries got me to thinking about mine and whether I should change them based upon time.
They have been in the truck 4 years and 6 months or so. I was reading some older threads recommending changing around the 3 year mark to prevent damage to the FICM.
I don't drive the truck everyday and sometimes it sits for 3 weeks or so. I noticed 2 days ago when I took it to work, I got one of the slowest cranks I've ever gotten. But after it's started and the glow plugs turn off, I get ~ 14.1 - 13.4 or so volts.
FICM voltage never drops below 47 and usually runs between 47.5 and 48.5 volts.
I'm not sure what size alternator is on there. Plus it's a single. I also have the upgraded cables that Mr. Jack recommended for extra battery life. I guess it's time for batteries though?
View 14 Replies
I have a '01 7.3 Excursion 2WD. 220,000 miles. It has a 4" exhaust, K&N filter and Edge Reprogrammer set on emission illegal. It gets the best fuel economy and moves out very well for 8000 lbs. Recently, I started to feel a surge while making light throttle acceleration. For example, round a corner at 35 and try to gently resume the 45 Speed limit. It begins to accelerate and then cuts out or surges, sometimes several times. If I lay into it, it responds fine. I have serviced the air filter, the fuel filter, use synthetic Amsoil. I did notice a slight improvement after the service. Less frequent cutting out or surging. I also was in an area where Bio diesel is readily available. I added almost a full tank of B10 Bio and it seemed to work. Changed the fuel filter just after.
It has been cold for NC. This morning it was +14 when I started the truck. It seemed to finally catch on maybe 2 cylinders with lots o' white/ blue smoke. It cleared out in a few minutes and seemed to be hitting on all 8, or at least 7. Once it warmed up, it's fine. But I had the codes p0672, p0674, p0676, p0678. My question is: Is there a common thread in the fact that it appears that I lost 4 glow plugs on the same bank?
One arm chair quarter back's response to the surging, is that the under valve cover injector wiring harness may be breaking down, especially since the truck has 220,000 and the valve covers have never been off. I have a fresh turbo with the good wheel sitting ready. I have just been too lazy to swap it out. Would a fresh set of injectors be a wise choice, when I swap over?
View 14 Replies
Background: '01 Excursion 7.3 4WD, 264,xxx miles, batteries less than three years old, new alternator [URL] .... , using an Edge Insight for digital readings.
Problem: I replaced the alternator about three weeks ago, first week all normal. Second week alt/battery idiot light comes on, then to add more frustration it is consistently inconsistent in its reading.
The volts (upon starting) jump around 11.6 - 12.1 when first starting. The light comes on while accelerating and goes off during no throttle while cold.
After warm-up the light will come on intermittently even though the reading is 13.0>, but never during off throttle.
It seems to do this more when cold but it does not completely stop when it's warm. Yes, I don't think that should be a factor but it is a reality .
I'm thinking it's a bad voltage regulator.
View 4 Replies
This is a 1999 with 200k on it. It has a really bad hpop so valley is full of oil. Haven't removed the HPOP to inspect the non serviceable plug or the hpop gasket. doing that this week. This truck I just bought and it has aftermarket injectors so dont know the miles in injectors. once the oil leak is resolved I can then give the injectors the once over to make sure theyre okay. Question is how much of a stream of oil should I expect to see as the engine runs?
View 11 Replies
My 2001 7.3 is smoking only when barely on the gas. New fuel filter. Don't know if its possible injector going bad or what? Smoke is white not black.
View 1 Replies
Batteries are a year old. Drove to work. Now won't turn over even with a diesel truck jumping. Voltage above 12 and slowly drops when cranking.
View 14 Replies
I have a 2002 F250 4x4 Powerstroke with Automatic. I have been having off and on issues for months with the throttle going dead. This only happens when I start it, if it works when started it will continue working until a different start session.
I have replaced the pedal several times before learning how to check its output with a meter and am quite sure that is not my issue at this time. However, when the pedal is depressed the check engine light lites up and nothing happens.
I am thinking it must be the computer itself, but was told there is another sensor or module under the hood that could cause the issue also which is several hundred dollars to replace as would be the computer.
Is there a way to test the computer, and what is this other module/sensor if it exists that could be the issue? Unhooking and rehooking the battery to reset the computer is no longer working to buy me a few more weeks, is there a simple way to reset the computer to try?
I love this truck when the throttle works but I am getting tired of paying on a truck while having to borrow a vehicle to drive to work.
View 5 Replies
2003 F-350 - 7.3. With the key in the on position there is zero voltage to the fuel pump. Fuel pump fuse is good. I traced the red with black tracer wire from the pump up through the firewall and to the safety inertia switch. The switch has continuity so it's OK. Then from the safety switch I traced the green with yellow tracer wire to a fuse block plug connector. Then I checked continuity from that connector out to the #40 fuel pump fuse and it's open.
So I then i checked from the fuel pump fuse to all the back connections on the back of the fuse block and there was no continuity to any of them. So I removed the back cover off the fuse block to expose any issues. I found two board mounted relays. Now, from the fuse I get continuity to one of the relay connections. So did Ford hide the fuel pump relay and make it non replaceable? Also if this is the pump relay then what circuit energizes it? I need to make sure before I replace the fuse block.
View 14 Replies
My right front window would barely move when I was opening it. Binding real bad on the way down. So I pulled the door panel, ( a two minute affair ) lubed all the tracks with silicone grease. Now the window goes down very easily.
I had all four doors done in an hour. To remove the door panels, remove the red reflector from the door, remove the screw underneath of it. Gently pry up on the window switch bezel at the front for the front door, and the side for the rear doors if so equipped. There will be another screw underneath. Unplug the switch, remove the screw. Remove the trip piece from above the hinge area. Push up on the panel and it comes off.
I used that real thick silicone grease that you can get a plumbers supply for lubing faucet o-rings. It looks like double thick vaseline. Windows work like a dream now.
View 14 Replies
So I have had this occasional hiccup that has gotten more frequent. I figured since our weather has been extra cold (lows about 15 F, around 22 F in the morning), that the temperature had been contributing to the issue. My truck would hiccup and burp out some white smoke. At first it didn't throw a check engine or any codes. As of recently I would get a check engine light, but torque pro could not get any codes, they would be cleared when I cycled the key. Anyways, I finally got some codes yesterday because it happened again. The codes where P0603 and P0344.
So I ordered 2 new CPS from Riffraff yesterday (hoping that they will be here today so I can install one). Fast forward to this morning and i get the hiccup again except worse. Now my truck would barely reach 20mph and it constantly bucked. I limped my way to work (only 4 miles) and of course I got a check engine light but there were no codes that I could retrieve with Torque Pro again. I had read on another thread that the guy had an issue with a wire in the harness near the 42pin connector for the IDM. He replaced his CPS taped up the wire and it went away.
I'm at work and now I'm paranoid that I wont be able to make it home. Is there anything temporary I can do for the CPS, like maybe disconnect it and spray it with some contact cleaner, until I can replace it? I'm going to trace the wire harness to make sure there aren't any bare wires. I forgot to mention that the local stealership replaced the CPS for free due to recall less than 3000 miles ago...
View 5 Replies
My Volt gauge on the dash has started reading around 10V with the key on waiting on the GP's. Batteries read +/- 12.6V with a DVM in a static state, no key.
But, quickly as best as I could see the reading on the DS battery drop to around 10V with the key on, GP's cycling. Cranking drops down around 8Vish.
After starting the reading on the DS battery is back up to 10V. This lasts anywhere from 30 seconds to a few min. Then it jumps up to the expected 14.6V reading.
I cleaned up the battery terminals and clamps while doing my turbo,and all the connections are tight.
View 14 Replies
2001 Ford Excursion 7.3 will run barely for about 20 sec. shudders, then dies. Bought new, driven 334K miles. Performed the usual fixes common to 7.3 issues over the years. All original injectors except for #7 which I replaced about 5 yrs ago. (I know should have replaced in sets but not in the budget at the time). Anyway had my wife turn the engine over after I had removed valve covers for inspection and observed a lot of smoke coming out of what appears to be at or around number 7 rocker arm valley? All rocker arm/pushrods look to be moving as they should beyond that I'm in over my head. Am I screwed or could it possibly just be a bad injector/injectors?
View 12 Replies
