Took a 2 hour trip got of the interstate came to a stop light and the OD light starting blinking cut the truck off at the light fired it back up shifted in every gear like normal drove a little ways stopped at a light and OD started blinking again cut truck off back on light. Went away shifted great threw all the gears.
View 6 RepliesI have a 2001 3/4 pickup. Sometimes the over drive light flashes. When it flashes it shifts really hard and sometimes it won't shift into 4th until I mash the overdrive button. Sometimes the light doesn't flash at all and it doesn't have any trouble shifting at all. Is it a solenoid? Or wiring issues?
View 6 RepliesSo here's the deal: My 2000 F250 has began to have the overdrive light blink when I am traveling at low speeds <40mph and it is accompanied by strange shifting (lower gear for a longer period of time). As soon as I get up to highway speeds the blinking stops and goes back to normal operation. But as soon as I go back to low speeds it happens again. When I put the truck in to park when it has the light blinking it revs it self to about 1200rpms then goes back to normal idle. This truck has 228k miles and is on the original transmission.
View 5 RepliesI have a 2000 f250 with the 7.3 and 181,000 miles on it, recently got stuck in the snow (in 2wd because i forgot to lock the hubs) and the rear wheels did alot of spinning. Now i randomly have the OD light start to blink, sometimes its a half a blink, sometimes it'll stay on for a few seconds, itll do it randomly while crusing down the road at a constant speed, also noticed my rpms fluctuate a tad at idle.
View 4 RepliesI have a 4r100 on in a 99 7.3 4x4. The shifting problem I have appears to be intermittant. it seems loose after warm up especially at the 4th shift overdrive and passing gear. possibly due to low presures ? sometimes (lately more often than not) hunts back and forth between 4th and o.d when passing or hill climbing. Under normal driving it shifts somewhat firm with 4th being an exeption.I have changed my crank position sensor filters and fluids which had turned dark and improved slightly. When I pulled the pan and replaced the filter the pan was spotless. No residue or signs of plates or debris. There is about 100,000 miles on the tranny and 350,000 on the truck. Questions: Is there a tcm for this transmission and if so could it cause these problems? I'm considering a purchase of an unlocked 1705 superchip to change the shifting but unsure if this will work for my issues...
View 14 RepliesTruck : 2000 F250 XLT A/T 6.8L v10 4x4
Issue : O/D off light is flashing on the shift lever. In a drive gear (R, OD, D2, D1) there is very low power when giving it gas, more so from a stop. In P and N, I can rev the motor with no obvious issues. In O/D, I can't even get forward momentum going from a stop when on a slight incline. When on flat ground and in O/D, flooring the gas only gets me going a few MPH and RPMs don't go above 1500ish. When selecting 1st or 2nd, the truck still struggles a bit from a stop but does get up and going.
What happened leading up to the issue : I was on the freeway driving about 80MPH without cruise control se,t and with O/D on as usual, when the blinking O/D off light caught my attention. Not knowing at the time that this was a transmission problem light, I started pushing and holding on the O/D on/off button to try and get it to stop. Probably about a minute later, I realized I was losing speed even when giving more throttle so pulled over to the shoulder. I shut the truck off and restarted it, noted the Service Engine Soon light was now on, then I put it in O/D and gave it gas but only got going a couple MPH which it sounds like the engine was choking/struggling. I then tried D1 and D2 and, while still struggling a bit from stop, was able to accelerate up to 35+ MPH.
OBDII Codes:
P0743
Torque Converter
Clutch Solenoid
Circuit Electrical
P0750
Shift Solenoid A
P0755
Shift Solenoid B
P1747
Pressure Control
Solenoid A Short Circuit
P0443
EvaPorative Emission
System Purge Control
Valve Circuit
P0135
O2 Heater Circuit
(Bank 1. Sensor 1)
P0155
O2 Heater Circuit
(Bank 2. Sensor 1)
Troubleshooting : Transmission fluid check looks good (full and red)
Checked fuse 23 of the Central Junction Box
Held a ground wire to bottom of Transmission pan and to the frame while I started the truck, O/D light still flashing
Wiring looks good coming to the plug on the driver side of the transmission
More info:
- No "Service Engine Soon" or blinking O/D off light prior to all this happening.
- I don't believe I'm getting 1st gear. I don't recall if I got my speed up to 30+ MPH while in D1, but while in D2 I never noticed a shift from stop to ~35MPH. At 35MPH, my RPMs were around 2500 I believe.
- While cruising at 35MPH in D2, shifting to O/D results in lost power. I had to stay in D2 all the way home.
To do (I believe):
1. Check shift solenoids (looking for DIY info)
2. Check shift solenoid pack (looking for DIY info)
3. Check TCC solenoid (looking for for DIY info)
It sounds like there are a couple shift solenoids to check as well as a solenoid pack (how best to check these out, I'm still looking for)?
I have an early 1999 Ford F350 4x4 7.3. I purchased it used about a year ago. The trans was replaced with an ATS 4R100 and a billet torque converter. I have the paperwork for it to confirm it along with the mileage when it was installed. It currently has about 35k on the new trans.
Several months ago the trans heated up to about 200 degrees on my trans temp gauge that was already installed when I purchased it. Not a huge deal and after pulled over and high idling it off I went and no problems.
About a month ago I was towing my fifth wheel when I noticed the temp rising on a level grade. I also noticed the OD light flashing. I made it home and when I went to drive it the next day light was not flashing and it shifted and drove like normal without the trailer.
I towed the trailer again and same thing, OD light flashing and started heating up. I changed all the fluid and flushed it based on the trans flush procedure I got in this forum and replaced with an OEM trans filter. Towed the next day and everything was good. Temp was good and no OD light flashing but I lost 4th gear. All other gears shifted fine, no slipping, just won't go into 4th.
On my way back home the OD light started flashing again and instantly the heat started rising on the trans again. I was finally able to get it into 4th if I let off a little, but as soon as the OD light started flashing I lost it again.
I have a friend of a friend who works for Ford who offered to come over to hook his scanner up. When he hooked it up there was no stored codes from the OD light which we both thought was odd. Took it for a test drive and the OD light started flashing so we could get some readings. He said it showed an error shifting from 1 to 2 and another error when shifting from 3 to 4. I unfortunately forgot to ask him for the specific codes. He tried to read the torque converter info but said my truck was to old and the PID was not supported to read that info.
He said it appeared it was mechanical but without some type of break out box where he can physically shift the gears he couldn't say for sure if it was mechanical or electrical. He did not seem to interested in doing that test for me as he rebuilds trans on the side and said he could rebuild it for me.
It seems my overheating takes place when the OD light starts flashing. It still drives fine and shifts smooth with no issues with or without the OD light flashing. 4th gear usually doesn't work but on a rare occasion it will go into 4th fine which makes me believe it may be electrical.
I am new to diesels but have learned a lot about my 7.3 lately. I recently installed injectors, up pipes, hutch mod, and several other little things so I can get things done myself but am just a DIY'er who can follow good directions. I know very little to nothing about transmissions though.
While working on another issue I did notice there is a large wiring harness that connects up on the driver side of the trans. I unplugged it and was checking the wires and after removing the dirt and crud on it you could see the outside wire sheathing had deteriorated exposing the copper. I bought some liquid electrical tape and sealed everything up. I did look for a replacement wire harness at the time and the one I ordered was very similar but the plug was different so that is why I used the liquid tape at the time. I did not seem to have a problem at the time after fixing it but wanted to mention it here in case that may be an issue.
I also thought swapping out the solenoid pack may fix it. I did not want to drop the trans and send it for a rebuild if I did not need to. I know there are some other sensors associated with the trans like the TSS I think but don't know if they are even related to my issue.
I tried getting the codes from the guy but he does not have them and I can't get him back out. I have an OBDlink device connected to Torque on my phone but I couldn't get it to read trans codes. Could be user error.
The overdrive light is flashing but not all the time. What does this mean?
View 3 RepliesMy F350, 7.3 L. is flashing the overdrive light. Had a pro do a scan that said no Turbine speed sensor signal.
I would like to know where the TSS is located and then see if it has corrosion other reason not to connect.
Auto trans. The Overdrive light flashes on the Selector lever. Never stops.I put tape over it because it is annoying. Especially at night. It goes into overdrive no problem.
A Couple of times it did not flash and was stuck in first till I manually shifted. Then the light started flashing again and works normal. What now......RPM Sensor?
Auto trans. The Overdrive light flashes on the Selector lever. Never stops. I put tape over it because it is annoying. Especially at night. It goes into overdrive no problem.
A Couple of times it did not flash and was stuck in first till I manually shifted. Then the light started flashing again and works normal. What now......RPM Sensor?
Here is my issue. I have a 2000 e350 7.3 the overdrive light is flashing, the speedometer and the odometer isnt working it also shifts hard, i changed the vss, the vss plug, range sensor, and alternator. still acting up. also all the fuses are good.
View 8 RepliesSo my OD light started blinking on the way to work today. The fact that my truck dropped out of cruise control and then started downshifting out of OD on the freeway and back into OD started this ordeal. A quick scan of the dash made it easy to notice the OD light strobe, especially in the dark.
I've read some posts in the past in the event it happened to me since my truck is far from new. I had it in the back of my mind that I would attack the VSS sensor with some contact cleaner then replace if that didn't fix the problem. Doing a search revealed a far greater spectrum of culprits. In addition to the VSS potential I have read about transmission handles, chafed wiring in the steering column, and even the transmission itself. Instead of re-inventing the wheel I'm looking for those that have more knowledge on this issue than I do. Here are my symptoms:
1. Drove 5 miles from my house to the freeway with no issues.
2. Shortly after getting on the freeway I set my cruise control at 65mph.
3. Shortly after that my cruise control 'dropped out' and the truck started to slow down (obviously).
4. When I got back up to speed the cruise would not work which is when the out of OD and right back into OD started. It did that all the way to work (it would go out of OD and back in every couple of minutes or so).
5. Transmission hunted on surface streets too (25mph).
6. Turned the truck off, waited a couple of minutes, then started it back up. OD light is off and truck drives fine.
A couple of things to note. This is the first time anything like this has ever happened with the truck. Also, I have Torque Pro and my instantaneous MPG meter was at 0.0 the entire time this was happening. When I turned the truck off and back on, the MPG was displaying again normally. This is what made me thing something with the VSS connector.
I decided to search the issue and confirm my suspicions then found out that this could be a lot more difficult to pinpoint. Since it cleared up when I cycled the key I am ruling out a transmission issue (for now).
I plan on cleaning the VSS connector (that's the plug on top of the rear axle right?) and then pulling the cover off the steering column to see if I can see any chafed wires. Is there anything else to check out while I'm rooting around? I will add that my transmission handle has always been loose (I think the original owner used to drive with his right hand resting on the handle).
I drove the truck to work. It was fine. I start it up at quitting time and let it idle for a minute. When I pulled out of the parking lot and the od light started blinking. After about 8 miles I stopped at a red light. When the light turn green and I drove off the speedometer is working again. The od light flashed for another mile or 2 then stopped.
View 3 RepliesFunny shifts and OD light blinking. Have p0741 and p0743 codes. Checked wiring and no visible damage. Checked continuity on the purple-yellow TC wire from connector under hood and at Trans and their is none.?? Also will I hurt the Trans driving this way if the temp stays in check?
View 14 RepliesSpeedometer not working and O/D light blinks, I have a 450 and a 250, 99 and 2000. On 450 this is an intermiting problem. Stop truck turn ignition off, restart and it all works now. Just started on my 250 and stopping and turning ignition off cures the problems for a few seconds, after i get moving the speedometer doesnt work and then light starts blinking again O/D light. Where do I need to start?
View 7 RepliesInstalled rebuilt transmission 1 month ago. Have noticed reverse has started to go away. Feels like it is slipping or tires are losing traction with a lot of vibration in the steering wheel.(tires are not slipping that's just the way it feels).. Does it worse when trans is up to temp. I suspect feed bolts but want opinions.(Mark K.) All forward gears seem fine with no issues. I have never been under the pan deep enough to access the feed bolts.
View 3 RepliesWell stock trans went two weeks ago so warranty company had another stock one put it (4r100). Finally got the truck today and I noticed my overdrive was flashing. I have no issues though shifts fine speedo works Rpms are normal I checked fuse 19 under the dash that's fine so I'm lost
If I turn the key on I can use the button like normal but once I drive it just flashes. It works but flashes .
I have a 2000 Ford Excursion 4x4 7.3 with 230K miles, around 15,000 miles ago I replaced the transmission with a rebuilt 4R100, lately I have noticed a leak towards the back end where the transmission and the transfer case connects. Some of the bolts on the bottom of the pan have ATF on them, some others however do not. I have had to add a quart of ATF in the past couple of days in order for it to engage into drive when going from Park to Drive. I have to rev it before it actually kicks in. I'm hoping the leak is just being caused by a gasket either in the pan or connecting the trans to the transfer case..
View 7 RepliesDriving along today my trans started doing some weird stuff. It lost all gears. Forward and reverse. If I turned the truck off and let it sit a while it would go again for awhile then loose drive again. When I got home I checked fluid level and did KOEO o/d off and back on. I drove it around the block and it seemed ok, so I went on my way. After about 20 min I noticed the OD light flashing. I checked codes and It had P1754-ccs.
View 14 RepliesOK, truck is 2000 F350. I am heading on a 2000 mile roadtrip to Yellowstone for my wife's 40th birthday in two days. What was our rock of a vehicle is now causing me severe anxiety.
Over the last few days the truck has been difficult to start - almost stops turning over as if the batteries were low. So I ignored it because if I plug it in, it starts fine and if I drive it and it gets hot - it starts fine.
Tonight while driving - I noticed a high idle and then it went to normal - I thought it was weird and a few miles later at a stop sign it struggled at idle, sort of loping but not romping very high and the over drive light started blinking. When I got home when I went from drive to neutral it goes to high idle and then the overdrive light blinks. The first time it blinked it went off when I pressed the OD button - but now it continues to blink.
Would low batteries be the root cause of this? I will continue my search for blinking OD light but I thought I would get this in the queue in case this is bigger than I can handle. I have 48 hours to resolve this issue - leaving Wednesday early morning.