Ford 7.3L Power Stroke (1999-2003) :: 2002 - Lowering Rear To Level?
Nov 18, 2015
I'm fresh out of the perverbial womb to this place and only about a toddler when it comes to my truck. However I do want to learn! I just recently invested in an 02 XLT F350 7.3L. I'm in love with the truck except the leaning forward aspect. I am debating on leveling it via lowering the rear. Any thoughts? Things I need consider that will happen if I do? How would you do it? Would you do this over raising the front? I've heard raising the front can mess with the suspension geometry and that's not a good thing to do!
View 10 Replies
Advertisement
My friend bartered for a '99 F250, 2wd/auto, 4 door, 7.3, 258k miles.
It had reportedly sat for one year, though the expired registration sticker and other things point to it sitting for two.
It ran low on oil, sputtered and died. Oil in the degas tank. Filled to oil to mid way on the hatch marks on the dip stick.
I drove it 25 miles to my house, and the oil level is not reading on the dip stick.
The sludgy fluid level in the degas tank is unchanged. Where is the fluid going?
I will refill the oil to see just how much it lost in the 25 miles if it important to someone, but I prefer to not waste the oil.
My first plan is to remove, inspect and replace the oil cooler o-rings. Even though the dealership charged him for this, I don't trust that they did it right. I think it is the easiest and mostly likely place for oil getting into the coolant.
It does have a really long crank before there is enough low pressure oil for it to start. At the moment I think this is a separate issue.
The dealership also charged him for a replacement injector. No idea if they replaced the cup or not.
View 14 Replies
...when changing the fluid and RTV'ing the rear differential cover?
Usual suspects: Brake cleaner, Simple Green, soap and water, gasoline, etc.
I've never serviced one, but figure it is like this:
1. Drain
2. Remove cover
3. Spray, clean, rinse, whatever all the innards
4. Wipe and dry
5. Inspect. For what, I have no idea
6. Black RTV cover back on, replace drain plug, remove fill plug
7. Refill with 75w-140w Mobil 1 Synthetic (not sure what it is, but I looked it up here some time ago and bought enough)
8. Fill to within a finger tip's dip in the fill hole
I've had the RTV and oil for a while, but it's supposed to hit 59F here on Saturday with no rain!!! Time to crawl on the floor and get it done.
I didn't see any problems with my cover, so going to forgo the new aluminum finned cover this time
Guess the biggest question is what should I use to clean/flush the rear end?
This is 2002 Excursion WITH LSD rear differential. 4WD.
View 14 Replies
I'm trying to figure out what axle I have on a 2002 f350 single wheel 4x4 so I can order a replacement seal. So this morning I got to work and noticed that am oily guild was dripping from the front of my rear differential where the drive shaft hooks into it. I figure it the seal, so when I went to look up the repair kit they list several different axle options because of gearing, what axle I have as there wasn't a in owners manual with the truck. Who can I find out what axle I have so I can buy the repair kit for it...
View 5 Replies
My truck (02 7.3L cc) started making a grilled ding type of vibration when I would let if the throttle. I felt the axle going into the rear differential was a bit loose, so I took the cover plate off. The pictures below show where the pinion I think is hitting, sort of like the bearing is allowing front to Rear differential scaring from movement. Rear movement.
How difficult is a rebuild, and is there anything I should be careful of?
View 14 Replies
I'm currently adding some hideaway strobes into my 02 POV and was wondering if any good place to enter wires from the rear of the vehicle? I'm not wanting to drill any holes and worst case I'll go through the firewall with my other runs and run down my door jam. All my connections are behind my rear seat.
View 6 Replies
So I know it's kind of a loaded question, but how low can the oil level get before a noticeable lack of performance occurs? Basically, how low does the oil level have to get before the truck will no longer pull itself up small hills at interstate speeds (70 mph)?
I will describe more of what occurred later on, but I want to get an idea if what I am thinking may be possible.
View 14 Replies
2002 F250 diesel ... I found these two plastic pieces yesterday on the floor near the 4X4 shifter. I noticed the other day when i step on the brake the rear view camera in the head unit comes on, so i am thinking they are either a part of the brake switch on the pedal assembly, or something to do with the shift tube.
View 2 Replies
I've been having a very erratic fuel gauge issue as of about 2 months ago. My fuel level would register full, when in fact I knew it only had 1/2 a tank or so. Then 5 minutes later it would be pegged on full. Under a 1/2 tank the gauge would read any where from 1/2 to empty from 1 minute to the next. So last week I decided to drop my tank and take a look. I was thinking maybe my fuel sender was broken, maybe a loose wire in the tank, or even that my float had dropped off in to the tank.
After dropping the tank, I removed the PK-Up and sending unit and everything was intact. I placed my ohm meter on the sending unit and it checked out fine. So I took the Pk-up and rolled back up underneath the truck and plugged it back in. I had my son turn the key on and off while I moved the float to different levels in order that it would register. It registered empty, 1/4/, 1/2, 3/4 and full just fine as I moved the float to those levels. If you leave the key in the run position and move the float, it won't register or better said, the in cab gauge will not adjust with the movement.
You have to turn the key off move the float and hold it there, then have your assistant turn the key on and the gauge will show the position that you've moved and held it at. I simply removed the plastic cover from the sending unit, and sprayed it down real good with electrical contact cleaner. I didn't scrub the copper contact area at all.
I was concerned that scrubbing might remove more than I wanted to, and really mess things up. I attached an Ohm meter and checked resistance thru out the float travel. All checked out good and I reinstalled it. So now my fuel gauge is working as it should be. I did make a video while I ohmed the Sender Unit thru it's travel, but for some reason it won't load.
[URL] ....
View 5 Replies
I have a 2002 7.3L Screw 4x4. Will a 03/04 6.0L instrument cluster work in this truck? The 2 clusters appear identical. I put the 6.0 cluster in and the trans temp, and coolant temp gauge will not work. All the gauges sweep when it is powered on, but the coolant and trans temp lay flat, and the check gauge light is on. All other gauges and functions work. When I put my other cluster in, all gauges work fine. Is there a difference in the VSM, PCM, or the SCP communication?
View 6 Replies
I just finished a cab swap and I'm having a little trouble. Here's a link to what I've done : [URL] ....
KOEO the WTS light, battery light, SES light all stay on and no power to fuel pump. No communication with PCM (using AE). All fuses are good, but no power to PCM fuse (#22). When I apply 12v to #22, the truck will start and idle - but poorly because I still don't think fuel pump comes on. The idiot lights all stay the same.
I did get to pull codes while it was running and got stuff like IAT circuit high (its not plugged in), fuel pump relay short to batttery, and a few other short to battery things (park assist stuff IIRC). I thought that might have something to do with the redneck idea to boost the fuse with an external power source?
Just thinking while typing, I don't have 3rd brake light hooked up yet (just thought of that, I'll hook it up first) and bed/bumper are not installed, so no tail lights or park assist stuff is hooked up. I'm also not using overhead computer, so it's not plugged in.
My next step is to go back through all of the connectors and make sure something isn't 1/2 way plugged in or possibly plugged into the wrong place(s).
Looking thru the wiring diagrams is not a strong subject for me, but I was trying to figure out how power gets to the fuse and how PCM relay works (does it complete circuit to ground to energize the coil?).
View 14 Replies
My issue I'm having - 2002 F350 7.3L has an 8 inch bds lift with 37/13.50 tires. I realize these tires are big but... while driving 100kms/hr or 60 miles per hour and I hit the gas the truck barely wants to move (without pulling a load). Thought maybe a turbo but I have no mechanical skills so here I am!
2nd issue, there's a bullydog chip in that truck when I bought it. he said he always ran it on extreme. I found it puffs way to much black when on extreme and on performance it seems a lot better so that's where I have it?.
3rd issue, the transmission gauge on the dash goes into red when climbing up hills ( I live in the rocky mountains so a lot!) but the bullydog chip says the tranny is only at its hottest 140C? I don't believe that's to hot but I do believe my truck is derating a little while the tranny gauge on the dash is in the red? is there any quick fixes out there for these issues.
View 6 Replies
I have a 02 f350 7.3 with 296,000k its been running ruff lately with a serious loss in power. The truck sounds good at idle starts up fine but when im on the throttle under load it almost crackles and sometimes bucks. I thought its was injectors replaced them all with stock ford remains but didn't fix the problem. I have AE and it passes a buzz test but i did a KOER test today and it started what seemed like a misfire during the test my ICP went to 2400-2500 and my IPR was at 38%. I have already put a new hpop in a couple month back along with new hpop lines do to a burst, ICP sensor, and i rebuilt the IPR valve. Not sure if this is a problem with fuel or the hpop I have also cleaned the screens in the tank and replaced the fuel pump which were pretty bad....
View 9 Replies
There was no power getting to the fuel pump on my 2002 Ford F250 73 diesel traced it back to the inertia switch no power in or out but I'm getting power at the fuel pump relay put the code scanner to the PCM and no communication....
View 9 Replies
I have a 2002 F-250 7.3, 159k on it. I bought it in March, ran AWESOME up till now. I was driving to work last week, check engine light came on, truck lost power and started idling rough. I have a buddy who works for a Ford dealer as a diesel mechanic, he came over with his scanner and laptop. #2,#4,#8 cylinders kept coming up saying possible problems are injectors, harness, rings.. He also did an electrical check, that all checked out. He told me to get injectors, so I got 4 injectors (yes I got the correct #8 injector), valve cover gasket, injector harness and 4 glow plugs.
The parts came last Friday, we did the job and it ran great. Drove it Friday night, Saturday, Sunday morning, no issues. Sunday afternoon we were on our way to a birthday party, truck started doing the exact same thing... Check engine light, rough idle, loss of power. After I got home from the party, my buddy came back over, put it on the scanner again, getting the same codes again. Deleted the codes, ran the tests again, same codes, deleted the codes, rant the tests again, same codes.
He said he is going to come by tomorrow with the box to check each individual cylinder.
View 14 Replies
I now have a 2002, 7.3, 250, 4x4 and love it. Everything but the milege. All in all it's a great ride. I have one little problem that's driven me nuts.
The power windows and the radio go out occasionally. Both at the same time. They come back on...... sometimes. Sometimes it takes a day or two. I've checked the fuses and then saw that there is a breaker in the 601 location in the fuse box that's probably causing the problem.
But I thought that it was supposed to shut off to protect that circuit when there is a short somewhere. I don't know where to go or how to locate the short if in fact this is my problem.
View 14 Replies
Last year I did some major work on my 02. Painted it, new injectors, 38R, and once it was back together, the transmission went south in a month. Got a Ford reman HD4R100. Shortly after the install, when in reverse, the torque convertor would lock up when you stepped on the throttle. As soon as you let off the throttle, it would disengage. Thinking it was a tranny issue, got another one from Ford. This one has been in the truck for about 9 months. And it seemed fine until about a month ago. It started doing the torque convertor lockup thing in reverse like the last one, but not as often.
Then last weekend it did it every time I put it in reverse. Then yesterday, while pulling away from a traffic light, there was a loud bang, and lost power in the transmission. Once stopped, I found out it has manual 1st and 2nd, but nothing else. No drive, overdrive, or reverse. I personally believe something electrical led to these issues, and ultimately, the transmission failure. I know the truck is not stock, but I do not run it hard very much. When it went bang yesterday, I was not being hard on it. Where to look at what is causing this?
View 14 Replies
I have a 2002 f250 CC 4wd 7.3 and I have no power to my reverse light sockets. I am stumped, all my fuses are good, I don't think there's a relay so i haven't checked that. My neutral safety switch is good, I'm getting power to both the blue/pink and black/pink wire. What it could be, at first it was constantly blowing fuse 27 every time I put it in reverse but then it stopped blowing it obviously because they won't come on.
View 8 Replies
Comming back from hunting today my truck suddenly lost power and stepping on the accelearator had no effect at all. We were on the highway thru the mountains but on a fairly level stretch for a few miles. Managed to pull the truck and toy hauler over and the engine was running fine but stepping on the accelerator had no effect. The check engine light came on every time I stepped on the throttle and went out when I released it. It started fine but no throttle response. Switched around a bunch of relays and checked the fuses and still nothing.
Not liking my parking spot i tried to see if it would move down the road at an idle but it would not. Then I thought to try it in 4 wheel low and as the shoulders were soft it wouldn't move forward so tried reverse and went back a foot, forward again and moved a foot and a half. did this several times and all of a sudden the throttle responded, took it out of 4 wheel and it ran fine all the way home. What would have caused this? I was ready to call a tow truck which would have been several hundred dollar bills for where we were and with the trailer
View 14 Replies
So after hitting a pothole, it would seem like half the engine lost power, after some searching around, i found that i would most likely be the harness inside the valve cover that has lost connection.
Its the right side, so i would need to take of the turbo pipe, and probably something else to get to it.
Since i'm doing this job, what to check out along the way? I want my 7.3 to be as reliable as possible.
I will probably ask some questions along the way, it can be a challenge sometimes to own a car that not many mechanics are familiar with, but as i have read online, this should be a very straight forward fix.
Can the harness be upgraded so it doesn't happen again? Its an 02
View 14 Replies
2002 F250 7.3L suddenly idling and running very rough, and doesn't have any power. Truck has been running perfect, it's my daily driver, and just put a couple hundred miles on it yesterday with no problems. I had been having some transmission issues when I tow heavy so I bought a new transmission yesterday. This morning I pulled the truck into my garage to change the transmission. Again truck ran fine, no signs of any issues before the trans swap. I changed out the transmission, which included unhooking the trans wiring harness from all the various sensors, and unbolting the starter.
I didn't mess with anything in the engine bay except for unhooking the batteries. I had also repaired the overdrive button wires, as they had been pinched in the steering column and the button wasn't working. When I got everything hooked back up I cranked it up to get the trans fluid flowing through the transmission, it started right up and idled good. I had it running for a few minutes and it was beginning to make a little more noise than usual. When I started to back out of the garage it was getting pretty rough, almost like it was running out of diesel. I put it in neutral and gave it some throttle and noticed I was getting white smoke out of the exhaust and could smell diesel pretty strong.
I checked my injector resistance at the valve covers and got around 4 ohms +/- on all of the injectors. I rechecked all of the clips and harness that I had messed with. I took a look at the ICP sensor and it has oil in the connector which I know can cause a rough running condition in some cases. It looks like it has had oil on it for a while. I unhooked the batteries again for about 20 minutes to try and reset anything that may have messed up. I checked a bunch of connections under the hood to see if anything was unhooked or loose.
I also cleaned up the connector on the ICP sensor. I started the truck back up and it idled perfect so I pulled it back out of the garage and headed down the driveway. It almost immediately started running rough again and barely had the power to go up a small hill. I pulled back in and tried unplugging the ICP while it was running, which made a slight difference in the idle but still very rough. I plugged it back in and the idle progressively got worse until it was chugging really bad. I shut it off after that and haven't messed with it again.
What might have happened? Could it be a bad sensor or transmission position sensor in the new trans? Is it just coincidence that this happened with a transmission swap? I am going to get a new ICP, but if there is anything else I can try/check before I can pick up the ICP on Monday let me know.
View 1 Replies
